Spirit Inspire ZE30 User manual

PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OP
ERATING YOUR NEW ELLIPTICAL!
Z100 / Z300 Z500 Z700
OWNER’S MANUAL

ZE30
1
Product Registration………………………………………………………….. 2
Important Safety Instructions………………………………………………… 3
Important Electrical Information…………………..……………………………4
Important Operation Instructions…………..…………………………………..4
Assembly Instructions………………………………..…………………………5
Transport…………………………………………………………………………8
Operation of Your New Elliptical…………………..…………………………...9
Manufacturer’s Limited Warranty…………………………………..………….16
ATTENTION- THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL USE
ONLY AND IS WARRANTED FOR THAT APPLICATION. ANY OTHER
APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY.
Table of Contents

ZE30
2
Thank you for your purchase of this quality elliptical from Spirit Manufacturing, Inc.
Your new elliptical was manufactured by one of the leading fitness manufacturers
in the world and is backed by one of the most comprehensive warranties
available. Through your dealer, Spirit will do all we can to make your ownership
experience as pleasant as possible for many years to come. The local dealership
where you purchased this elliptical is your administrator for all Spirit warranty and
service needs. Their responsibility is to provide you with the technical knowledge
and service personnel to make your experience more informed and any
difficulties easier to remedy.
Please take a moment at this time to record the name of the dealer, their
telephone number, and the date of purchase below to make any future, needed
contact easy. We appreciate your support and we will always remember that you
are the reason that we are in business. Please complete and mail your
registration card today and enjoy your new elliptical.
Yours in Health,
Spirit Manufacturing, Inc.
Name of Dealer______________________________________
Telephone Number of Dealer___________________________
Purchase Date_______________________________________
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this fitness product in the space provided below.
Serial Number_______________________________________
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to
Spirit Manufacturing, Inc or visit www.spiritfitness.com to register online.
CONGRATULATIONS ON YOUR
NEW ELLIPTICAL AND WELCOME
TO THE SPIRIT FAMILY!
Product Registration
ZE25-E07 0509/S1

ZE30
3
WARNING - Read all instructions before using this appliance.
■Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both
carpet and elliptical may result.
■Keep children away from the elliptical . There are obvious pinch points and other
caution areas that can cause harm.
■ Keep hands away from all moving parts.
■ Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not
working properly, call your dealer.
■ Keep the cord away from heated surfaces.
■Do not operate where aerosol spray products are being used or where oxygen is
being administered. Sparks from the motor may ignite a highly gaseous
environment.
■ Never drop or insert any object into any openings.
■ Do not use outdoors.
■To disconnect, turn all controls to the off position, then remove the plug from the
outlet.
■Do not attempt to use your elliptical for any purpose other than for the purpose it is
intended.
■The pulse sensors are not medical devices. Various factors, including the user’s
movement, may affect the accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate trends in general.
■Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable
for use on your elliptical . Quality athletic shoes are recommended to avoid leg
fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
Important Safety Instructions

ZE30
4
WARNING!
● NEVER remove any cover without first disconnecting AC power supply.
● If voltage varies by ten percent (10%) or more, the performance of your elliptical may
be affected. Such conditions are not covered under your warranty. If you suspect
the voltage is low, contact your local power company or a licensed electrician for proper
testing.
● NEVER expose this elliptical to rain or moisture. This product is NOT designed for
use outdoors, near a pool or spa, or in any other high humidity environment.
● NEVER operate this elliptical without reading and completely understanding the
results of any operational change you request from the computer.
● Understand that changes in resistance do not occur immediately. Set your desired
level on the computer console and release the adjustment key. The computer will
obey the command gradually.
● NEVER use your elliptical during an electrical storm. Surges may occur in your
household power supply that could damage elliptical components.
● Use caution while participating in other activities while using your ZE30; such as
watching television, reading, etc. These distractions may cause you to lose balance;
which may result in serious injury.
● Always hold on to a handrail or hand bar while making control changes.
Do not use excessive pressure on console control keys. They are precision set to
function properly with little finger pressure. Pushing harder is not going to make the unit
go faster or slower. If you feel the buttons are not functioning properly with normal
pressure, contact your Spirit dealer.
Important Electrical Information
Important Operation Instructions

ZE30
5
ASSEMBLY PACK CHECK LIST
■
■■
■ M8x20mm Button Head Socket Screw (4pcs)
■
■■
■ M8x15mm Hex Head Screw (6pcs)
■
■■
■ M8x50mm Button Head Socket Screw (2pcs)
■
■■
■ M8x45mm Button Head Socket Screw (4pcs)
■
■■
■ M4x30mm Self Tapping Screw (4pcs)
■
■■
■ 5/16” x 19 x 1.5T Curve Washer (6pcs)
■
■■
■ 5/16”x23x1.5T Flat Washer (8pcs)
■
■■
■ M8 Nylon Nut (2pcs)
■
■■
■ 13/14mm N Wrench (1pc)
■
■■
■ M5 Allen Wrench (1pc)
■
■■
■ Screwdriver(1pc)
Assembly
■
■■
■STEP 1
Install the Front and rear stabilizer into the Frame Base Support with 4pcs of M8x45m/m
Hex Head Screws and 4pcs of 5/16”x23x1.5T Flat Washers. Then tightly fasten 4pcs of
M5x38m/m Self Tapping Screws of the Front and rear Stabilizer Cover by using the
13/14mm N Allen Wrench and Screw Driver.
(As shown in Fig.1~7)
■
■■
■STEP 2
Connect the Computer Cable (Upper) with Computer Cable (Lower).
(As shown in Fig. 8)
■
■■
■STEP 3
Install the Front Post into the Main Frame with 6pcs of M8x15m/m Hex Head Screws
and 6pcs ofψ5/16”xψ19 x2T Curve Washers by using the 13/14mm N Allen Wrench .
(As shown in Fig. 9)
■
■■
■STEP 4
Connect the Computer Cable (Upper) with the Hand Pulse Cable. Install the Console
with 4pcs of M5x15m/m Button Head Socket Screws by using the Screw Driver.
(As shown in Fig. 10~11)
Assembly Instructions

ZE30
6
■
■■
■STEP 5
1. Install the Handle Bar Cover Front onto the Front Post with 1pc of M5x15m/m Button
Head Socket Screws.
(As shown in Fig. 12)
2. Take the Fix Handle Bar through the Hand Bar Cover Front and install it onto plate with
2pcs of M8x20m/m Button Head Socket Screws.
(As shown in Fig. 13)
3. Install the Handle Bar Cover Back onto the Front Post with 1pc of M5x15m/m Button
Head Socket Screws.
(As shown in Fig. 14)
■
■■
■STEP 6
Install the Lower Swing Bar into the Left and Right Swing Bar Upper and fix it by using
the Tension Adjuster.
(As shown in Fig. 15)
■
■■
■STEP 7
Install the Plastic Insert For Swing Bar (Lower End) into the Front Post and install Left
and Right Swing Bar Upper with 2pcs of M8x20m/m Button Head Socket Screws and
2pcs of 5/16”x23x1.5T Flat Washers by using the M5 Allen Wrench.
(As shown in Fig. 16~18)
■
■■
■STEP 8
Install the Left and Right Pedal Bar into the U Shape Plate For Pedal with 2pcs of
M8x50m/m Button Head Socket Screws, 2pcs of 5/16”x23x1.5T Flat Washers and
2pcs of M8 Nylon Nuts by using the N Wrench and the M5 Allen Wrench.
(As shown in Fig. 19)
■
■■
■STEP 9
Install the Swing Bar Upper Cover Front and the Swing Bar Upper Cover Back into the
Front Post with 4pcs of M4x30m/m Self Tapping Screws. And plug the two Hand Pulse
Cables into the Socket at back of Console.
(As shown in Fig. 20~21)
■
■■
■STEP 10
Install the Drink Bottle Holder onto the Front Post with 2pcs of M5x15m/m Socket Head
Cap Screws.
(As shown in Fig. 22)

ZE30
7
■
■■
■PLEASE LOCK DOWN ALL HARDWARE AFTER THE
ACCESSSORIES HAVE BEEN ASSEMBLED.
Assembly Photos

ZE30
8

ZE30
9
The elliptical is equipped with two transport wheels which are engaged when rear of
ZE30 is lifted.
Transport