Spirit XBR25 User manual

XBR25 Fitness Bike
OWNER’S MANUAL
Please carefully read this entire manual before operating your new tness bike

TABLE OF CONTENTS
1
2
3
3
4
9
10
13
16
18
19
ATTENTION
This tness bike is intended for residential use only and is warranted for this
application. Any other application voids this warranty in its entirety.
Product Registration
Important Safety Instructions
Important Electrical Instructions
Important Operation Instructions
XBR25 Assembly Instructions
Features
Console Operation
Programmable Features
Heart Rate Information
General Maintenance
Manufacturer’s Limited Warranty

XBR25 Fitness Bike
1
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this tness product
in the space provided below.
Serial Number
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to
Spirit Manufacturing, Inc. You can also go to www.spirittness.com/warranty.asp under
the support tab to register online.
Thank you for your purchase of this quality tness bike trainer from Spirit Manufacturing, Inc.
Your new tness bike was manufactured by one of the leading tness manufacturers in the
world and is backed by one of the most comprehensive warranties available. Through your
dealer, Spirit will do all we can to make your ownership experience as pleasant as possible
for many years to come. If not purchased direct from Spirit, the local dealership where you
purchased this tness bike is your administrator for all Spirit warranty and service needs.
Their responsibility is to provide you with the technical knowledge and service personnel to
make your experience more informed and any difculties easier to remedy.
Please take a moment at this time to record the name of the dealer, their telephone number,
and the date of purchase below to make any future, needed contact easy. We appreciate
your support and we will always remember that you are the reason that we are in business.
Please complete and mail your registration card today and enjoy your new tness bike
trainer.
Yours in Health,
Spirit Manufacturing, Inc.
Congratulations on your new tness bike and welcome to the Spirit family!
Name of Dealer
Dealer Phone #
Purchase Date
PRODUCT REGISTRATION
XBR25_20101129

XBR25 Fitness Bike 2
IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this appliance.
DANGER - To reduce the risk of electric shock disconnect your Spirit tness bike from
the electrical outlet prior to cleaning and/or service work.
WARNING - To reduce the risk of burns, re, electric shock, or injury to persons, install
the tness bike on a at level surface with access to a 110-volt, 15-amp grounded outlet
with only the tness bike plugged into the circuit.
DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH
ONLY ONE OUTLET ON THE END:
Do not operate tness bike on deeply padded, plush or shag carpet. Damage to both
carpet and tness bike may result.
Keep children away from the tness bike. There are obvious pinch points and other
caution areas that can cause harm.
Keep hands away from all moving parts.
Never operate the tness bike if it has a damaged cord or plug. If the tness bike is
not working properly, call your dealer.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is
being administered. Sparks from the motor may ignite a highly gaseous environment.
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the off position, then remove the plug from
the outlet.
Do not attempt to use your tness bike for any purpose other than for the purpose it
is intended.
The hand pulse sensors are not medical devices. Their purpose is to provide you
with an approximate measurement in relation to your target heart rate. Use of a chest
transmitter strap (sold separately) is a much more accurate method of heart rate
analysis . Various factors, including the user’s movement, may affect the accuracy of
heart rate readings. The pulse sensors are intended only as exercise aids in
determining heart rate trends in general.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for
use on your tness bike. Quality athletic shoes are recommended to avoid leg fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY!

XBR25 Fitness Bike
3
WARNING!
NEVER remove any cover without rst disconnecting AC power. If voltage varies by ten
percent (10%) or more, the performance of your tness bike may be affected. Such
conditions are not covered under your warranty. If you suspect the voltage is low, contact
your local power company or a licensed electrician for proper testing.
NEVER expose this tness bike to rain or moisture. This product is NOT designed for
use outdoors, near a pool or spa, or in any other high humidity environment. The
operating temperature specication is 40 to 120 degrees Fahrenheit, and humidity is
95% non-condensing (no water drops forming on surfaces).
IMPORTANT ELECTRICAL INSTRUCTIONS
NEVER operate this tness bike without reading and completely understanding the
results of any operational change you request from the computer.
Understand that changes in resistance do not occur immediately. Set your
desired resistance level on the computer console and release the adjustment key. The
computer will obey the command gradually.
NEVER use your tness bike during an electrical storm. Surges may occur in your
household power supply that could damage tness bike components. Unplug the
tness bike during an electrical storm as a precaution.
Use caution while participating in other activities while pedaling on your tness bike;
such as watching television, reading, etc. These distractions may cause you to lose
balance which may result in serious injury.
Do not use excessive pressure on console control keys. They are precision set to
function properly with little nger pressure.
IMPORTANT OPERATION INSTRUCTIONS

XBR25 Fitness Bike 4
ASSEMBLY TOOLS
1. Using a razor knife (Box Cutter), cut the banding straps that wrap
around the carton. Reach under the bottom edge of the carton and pull
it away from the cardboard underneath, separating the staples that join
the two together. Lift the box over the unit and unpack..
2. Carefully remove all parts from carton and inspect for any damage or
missing parts. If damaged parts are found, or parts are missing, contact
your dealer immediately.
3. Locate the hardware package. The hardware is separated into four
steps. Remove the tools rst. Remove the hardware for each step as
needed to avoid confusion. The numbers in the instructions that are
in parenthesis (#) are the item number from the assembly drawing for
reference.
PRE-ASSEMBLY
XBR25 ASSEMBLY INSTRUCTIONS
#114. Phillips Head
Screwdriver
#115. L Allen
Wrench
#112. 12/14mm
Wrench
#132. 14/15mm
Wrench
15
14

XBR25 Fitness Bike
5
1. Attach the Rear Stabilizer (7) to the Main Frame (1) with the four Hex Head Bolts (65) and four
Flat Washers (84). Tighten completely with the wrench (112).
2. Attach the Seat Back (5) to the Seat Carriage (4) of the main frame. Slide a Hex Head Bolt (67)
and a Hex Head Bolt (142) through each side, then attach a Flat Washer (77) and a Nyloc Nut
(89) to each bolt. Tighten the bolts just enough so there is no side to side play, but freedom of
movement front to back. Use the wrenches provided (112 & 132).
REAR STABILIZER & SEAT BACK ASSEMBLY
1
#77. 3/8” x 19 x 1.5T
Flat Washer
(4 pcs)
#84. 3/8” x 25 x 2T
Flat Washer
(4 pcs)
HARDWARE
#89. 3/8” x 7T
Nyloc Nut
(4 pcs)
#65. 3/8” x 2-1/4”
Hex Head Bolt
(4 pcs)
#67. 3/8” x 4”
Hex Head Bolt
(2 pcs)
#142. 3/8” x 4-1/4”
Hex Head Bolt
(2 pcs)

XBR25 Fitness Bike 6
1. Slide the Computer Cable (44) and Hand pulse Wire (133) through the bottom of the Console
Mast Cover (31) and then the bottom of the Console Mast (2). Make sure the Console Mast
Cover is correctly oriented (see illustration).
2. Install the Console Mast (2) into the receiving tube (make sure not to pinch cables (44) and (133);
damage to the electronics could occur) of the Main Frame (1). Insert two Hex Head Bolts (68)
and two Flat Washers (76) on each side. Insert two Hex Head Bolts and two Curved Washers
(83) on the front. Tighten all six bolts rmly with the wrench (112).
3. Remove the white Styrofoam pad (factory installed to prevent bolts from being accidentally
dropped into the console mast tube).
4. Attach the Handle Bar Assembly (3) onto the Console Mast (2) bracket with the two Hex Head
Bolts (68), two Split Washers (82), and two Flat Washers (76). Completely tighten with the
wrench (112).
CONSOLE MAST ASSEMBLY
2
#82. 8 x 1.5T
Split Washer
(2 pcs)
#83. 5/16” x 19 x 1.5T
Curved Washer
(2 pcs)
#68. 5/16” x 15mm
Hex Head Bolt (8 pcs)
HARDWARE
#76. 5/16” x 18 x 1.5T
Flat Washer
(6 pcs)

XBR25 Fitness Bike
7
1. Install the Seat (61) on the Seat Carriage (4) with four Phillips Head Screws (98). Tighten with the
Phillips Head Screw Driver (114).
2. Attach the Seat Handle Bar (6) to the Seat Carriage (4) with the four Hex Head Bolts (71), four
Flat Washers (77), and four Nyloc Nuts (89). Tighten with the wrenches provided (112 & 132).
3. Plug the Hand Pulse Sensor Cables (27) into the left side of the rear plastic cover.
SEAT & HANDLE BAR ASSEMBLY
3
#98. M6 x 15mm
Phillips Head Screw
(4 pcs)
#77. 3/8” x 19 x 1.5T
Flat Washer
(4 pcs)
HARDWARE
#89. 3/8” x 7T
Nyloc Nut
( 4 Pcs)
#71. 3/8” x 1-3/4”
Hex Head Bolt
( 4 Pcs)

XBR25 Fitness Bike 8
1. Remove the M6 Button Head Socket Screws holding the clamps of the left Release Lever (40)
by using the M5 Allen Wrench (115). Install the Release Lever (40) onto the Handle Bar Seat (6)
just behind the Hand pulse sensors on the left side (when facing the front of the bike). Install it at
an angle that allows easy access for use, then reinsert and tighten the socket screws removed
earlier. Don’t over tighten these screws.
2. Secure the Steel Cable (59) to the Seat Handle Bar (6) with the Velcro Tape. Wrap the tape
around the handlebars in places that will be under the beverage holders so they are out of sight.
3. Attach the Pedals (L, R)(116,117) to the Crank Arms (51L, 51R). Tighten with the wrench (132).
Remember that the left pedal has a reverse thread and will be threaded onto the Crank arm in
a counterclockwise motion. There is an “L” stamped in the end of the threaded post of the left
pedal and an “R” in the right. Make sure to tighten the pedals as rmly as you can. It may be
necessary to re-tighten the pedals if you feel a thumping while pedaling the bike. A thumping or
clicking noise is usually caused by loose pedals.
4. Insert the Computer Cable (44) and Hand Pulse Cable (133) into their respective connectors in
the back of the Console Assembly (19). Attach the console onto the mounting plate with four
Phillips Head Screws (99). Tighten with the Phillips Head Screw Driver (114).
5. Attach the Front Stabilizer Cover (32) and the Rear Stabilizer Cover (37) to the Main Frame with
four Phillips Head Screws (99). Tighten with the Phillips Head Screw Driver (114).
6. Attach the Drink Bottle Holders (L39 & R38) to the sides of the Seat Handle Bar (6) with four
Sheet Metal Screws (105). Tighten with the Phillips Head Screw Driver (114).
PLASTIC PARTS ASSEMBLY
4
#105. 4 x 16mm
Sheet Metal Screw
(4 pcs)
#99. M5 x12mm
Phillips Head Screw
(8 pcs)
HARDWARE