Sport-thieme 120 8405 Product guide

Operating/assembly instructions
Sport-Thieme parallel bars
Product code: 120 8405, 120 8418, 120 8421
page 1 of 4
04/2016
!
!
38367 Grasleben / Germany
Telephone: [phone]
www.sport-thieme.com!
Operating/assembly instructions Sport-Thieme parallel bars
Thank you very much for choosing a Sport-Thieme product. Please read the
instructions fully before you assemble the equipment so you can enjoy the product
and its guaranteed safety:
1. Description
All bars models comply with DIN 7901 ‘parallel bars with inlay mat’, including
DIN EN 914 ‘parallel bars and combined asymmetric bars/parallel bars’. The
regulations described there, with regards to area of use, inspection,
measurements and maximum loads, apply.
The uprights are attached to the welded base frame with cast bells. The cross
girders are closed off with special rubber inserts which are floor-friendly and
protect the sides when moving the apparatus. The generously sized castors,
which can be lowered using a handle, are housed in the cast bells.
Adjust height and horizontal position using a double secured clamping lever.
The respective technical regulations valid at the time of delivery apply to
design, function and use of the apparatus (the edition at the time of delivery is
valid).

Operating/assembly instructions
Sport-Thieme parallel bars
Product code: 120 8405, 120 8418, 120 8421
page 2 of 4
04/2016
!
!
38367 Grasleben / Germany
Telephone: [phone]
www.sport-thieme.com!
2. Use
Depending on their norm compliant design, bars are a sports apparatus for
competition, club training and school sports. In addition to the norm, the
guidelines of the national and international artistic gymnastics federations
apply to the intended use.
Always ensure appropriate and safe operation. Check that all bolts sit correctly
after setting up and before actually using the bars. Carry out a visual check of
the apparatus before and after each use. In the areas where the bars and
uprights are mounted, in particular, ensure that all connections are faultless
and check for possible tears. Should defects like these occur, the apparatus
must not be used!
3. Improper use
Improper use voids the manufacturer’s warranty and guarantee obligations.
This includes changes to parts of the apparatus or to the entire apparatus as
well as exceeding the permitted loads.
4. Assembly
Assembly is done by the customer only.
We deliver the bars without pre-drilled holes. For mounting, place the bars on
the bar brackets and mark the drilling holes on the bars. For this, the bar
brackets must be lengthways of the cross girders. After that, pre-drill the bars.
Before screwing them into the pre-drilled holes, the special screws M8x35
should be dipped in standard grease. This prevents the screws from breaking
off during the bars’ assembly. You must also ensure that the screws are not
tightened any further once the screw head is in contact with the bar bracket.
This prevents the screw head from turning off or being damaged. We
recommend mounting the bars using a hand-operated ratchet with a suitable
bit.
The apparatuses are almost maintenance-free, only the joints, shafts and axles
should be greased using a non-dripping lubricant. From time to time, the bar
posts should be wiped using an oily cloth.

Operating/assembly instructions
Sport-Thieme parallel bars
Product code: 120 8405, 120 8418, 120 8421
page 3 of 4
04/2016
!
!
38367 Grasleben / Germany
Telephone: [phone]
www.sport-thieme.com!
5. Operation
For transportation, lower the castors by turning the transport lever by 180°.
You can now move the bars to the required location.
Please ensure that no people are on the bars during transport. At the required
location, the castors be slowly
retracted.
To adjust the bars’ height, release the
clamp fastener using the clamp lever
(1) and pull out the bars to the
desired height (2) simultaneously and
as parallel as possible. Never pull out
the bar posts completely. The safety
catch must always be engaged and
keep the post in the last position.
In order to adjust the width between
the bars, turn them inwards or
outwards on the posts using the
crank (3). Now close the clamp
fastener again (1).
To lower the bars, release the clamp
fastener (1), lift the bar slightly and
press the catch (4).
After that, push the bar posts with the
bars slowly into the uprights (2) and
close the clamp fastener again (1).
Transport!lever!

Operating/assembly instructions
Sport-Thieme parallel bars
Product code: 120 8405, 120 8418, 120 8421
page 4 of 4
04/2016
!
!
38367 Grasleben / Germany
Telephone: [phone]
www.sport-thieme.com!
6. Hazard warning
•When lowering the castors or the bars, no one is permitted to be in the
bars’danger zone.
•When lowering the bars, do not hold on to their posts. There is a risk of
crushing.
•Be careful when setting up and removing the bars, there is a risk of crushing.
•The apparatus must only be used by authorised and qualified
people.
•Always firmly tighten all of the screws.
•Improper handling can lead to damage and tears to frame, bars,
uprights and castors. Therefore, these parts in particular should be
checked before, during and after use.
Assembly is done by the customer only. The apparatuses are almost
maintenance-free, only the joints, shafts and axles should be greased using a
non-dripping lubricant. From time to time, the bar posts should be wiped using
an oily cloth.
Caution: Do not overload the equipment!
Maintenance and care instructions
Instructions: Carry out a visual check at regular intervals. Due to our
continuous quality control of the products, technical changes
may occur which may lead to slight deviations in the
instructions.
Check at regular intervals that the screw connections are tight.
Check the equipment for possible damage and replace
worn-out parts. Check the condition of wooden elements
as chipping and other signs of wear can result from use.
Ensure that moveable parts are free-moving.
We are happy to answer any questions you may
have.
Your Sport-Thieme Team