SportsArt Fitness E835 User manual

E835 OWNER’S MANUAL CONTENTS
1. INTRODUCTION .............................................................................................................. 2
2. SAFETY PRECAUTIONS ................................................................................................. 3
3. WARNING LABLE POSITION .......................................................................................... 5
4. LIST OF PARTS ............................................................................................................... 6
5. ASSEMBLE THE PRODUCT ............................................................................................8
STEP 1 Install the Frame ..................................................................................................... 8
STEP 2 Install the Glide Rail ................................................................................................ 13
STEP 3 Install the Pedestal Covers ..................................................................................... 14
STEP 4 Install the Foot Pedals ........................................................................................... 15
STEP 5 Level the Product .................................................................................................... 17
STEP 6 Install the Ground Wire ........................................................................................... 18
STEP 7 Unit Inspection ........................................................................................................ 19
STEP 8 Beware of Moving Parts .......................................................................................... 20
6. UNDERSTAND THE E835 DISPLAY ................................................................................ 21
DISPLAY Overview ...............................................................................................................21
DISPLAY Specications ...................................................................................................... 22
DISPLAY Windows ............................................................................................................... 22
DISPLAY Keys ..................................................................................................................... 22
7. OPERATE THE PRODUCT .............................................................................................. 24
OPERATION Safety Operating Area .................................................................................... 24
OPERATION Safety Get On/O󰀨 ........................................................................................... 25
OPERATION Proper Workout Position ................................................................................. 26
OPERATION Adjust Stride Length and Resistance Level .................................................... 27
OPERATION Quick Start ......................................................................................................28
OPERATION Start a Workout Program ................................................................................ 29
OPERATION Display ........................................................................................................... 31
OPERATION Cool Down ...................................................................................................... 32
OPERATION Workout Programs .......................................................................................... 33
OPERATION User Information and User Preference Setting.................................................... 36
8. ABOUT HEART RATE DETECTION ................................................................................ 38
HEART RATE Telemetry ...................................................................................................... 38
HEART RATE Contact ......................................................................................................... 38
9. GUIDELINES FOR EXERCISE ........................................................................................ 40
10. MAINTENANCE ............................................................................................................. 41
MAINTENANCE Safety Precautions .................................................................................... 41
MAINTENANCE Messages .................................................................................................. 41
MAINTENANCE Lubrication Procedure ............................................................................... 42
MAINTENANCE Schedule ................................................................................................... 43
MAINTENANCE Task List (Elliptical Trainers) ...................................................................... 44
MAINTENANCE One-Year Maintenance Log ....................................................................... 45
11. ACCESSORIES ............................................................................................................. 46
ACCESSORIES Standard............... .................................................................................... 46
ACCESSORIES Options ..................................................................................................... 47
12. APPENDIXES ................................................................................................................ 48
APPENDIXES Specications ............................................................................................... 48
APPENDIXES Electronics Block Diagram ............................................................................ 49
*We reserve the right to revise this manual at any time without notice.

2
1. INTRODUCTION
Congratulations on your purchase of one of the nest exercise products on the market today,
the SportsArt E835 Elliptical trainer. Constructed of high quality materials and designed for
years of reliable usage, this product was made to become an integral part of your commercial
tness venue.
Before this product is assembled or operated, we recommend that you familiarize yourself with
this manual. Understanding the correct assembly and operation of this product will help ensure
that exercisers obtain their tness goals safely and successfully.

3
2. SAFETY PRECAUTIONS
Your SportsArt elliptical trainer was designed and built for optimum safety. However certain
precautions apply whenever you use your elliptical trainer.
Please read the entire manual before assembly and operation. Also, please note the following
safety precautions:
● Please read the instructions carefully and install the elliptical trainer as instructed.
● Assemble and operate the elliptical trainer on a solid, level surface. DO NOT use outdoors or
near water.
● Check the elliptical trainer before every use. Make sure all parts are assembled, and all fasteners
are tightened. DO NOT use the elliptical trainer if the unit is disassembled in any way.
● Keep your hands away from moving parts.
● Wear proper workout clothing; DO NOT wear loose clothing. DO NOT wear shoes with leather
soles or high heels. Tie all long hair back. DO NOT go barefoot on this product.
● Be careful when mounting and dismounting the unit.
● The elliptical trainer may or may not stop immediately if an object becomes caught or impedes
normal motion.
● Do not use accessories or parts that are not specically recommended by the manufacturer
(SportsArt). Such parts might cause injuries or cause the unit to fail and void the warranty. We
are not responsible for any safety issue that arises due to the misuse of accessories or parts.
At the same time, we will terminate the warranty terms of this equipment.
● Close supervision is necessary when this elliptical trainer is used by, on, or near children 14 or
younger, invalids, or disabled persons.
● Use this elliptical trainer only for its intended use as described in this manual.
● Never operate this elliptical trainer if it has been damaged in any way. If it is not working properly,
or has been dropped or damaged, contact your dealer.
● Keep all air ventilation areas free of blockage.
● Never drop or insert any object into any opening.
● DO NOT operate where aerosol (spray) products are being used or where oxygen is being
administered.
● Please refer to the product specication table in the appendix for the user maximum weight.
● Contact your SportsArt representatives on all materials damaged in shipment. (Note: Shipping
damages are the responsibility of the carrier.)
● Unpack and verify contents of boxes according to the list of parts to check if any parts are
missing.
● This product is not equipped with a free wheel and therefore the moving parts cannot be stopped
immediately.
● This elliptical trainer is not intended for use by persons (including children 14 or younger) with
reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of this elliptical trainer by a
person responsible for their safety.
● Children 14 or younger should be supervised to ensure that they do not play on or near the
product.
● Maintenance and repair must be performed by trained service personnel only. Improper
maintenance would not only damage the machine, but may also may present a danger to the
exerciser.
● Warning that any of the adjustment devices that could interfere with the user’s movement
should not be left projecting.
● To reduce the risk of injury from moving parts of electric shock, unplug before cleaning or
servicing.
● WARNING — This stationary training equipment is not suitable for high accuracy purposes.

4
2. SAFETY PRECAUTIONS (CONT.)
Caution
If you feel any pain or abnormal sensation, STOP YOUR WORKOUT and consult your physician
immediately. Work within your recommended exer-cise level. DO NOT work to exhaustion.
Before beginning any exercise program, you should consult with your doc-tor. It is
recommended that you undergo a complete physical examination.
DO NOT step onto the highest footplate. While holding onto supports for stability, step onto the
lowest footplate.
Note: This equipment has been tested and found to comply with the limits for a digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particu-lar installation. If the user desires to
correct such interference, it is at the user’s own expense.
Warning
Heart rate monitoring systems may be inaccurate. Over exercise may result in serious injury or
death. If you feel faint, stop exercise immediately.

5
3. WARNING LABEL POSITION
If you are a French speaking person in North America, please place the following label
contained in the owner’s manual on the console as shown. Customers outside of North America
will not receive this French warning label.
(Note: If there are any other warning labels contained in the owner’s manual, please place them
on the clearly displayed location on the console as well.)

6
4. LIST OF PARTS
A1 A2
A3
A8
A4
A5
A9
A6
A7
A12
A11
A10
Assembly Parts
No. Name Qty. No. Name Qty.
A1 Main frame 1 A8 Support tube, left 1
A2 Stationary handlebar 1 A9 Support tube, right 1
A3 Pedestal covers, left 1 A10 Foot pedals 1
A4 Stationary handlebar cover, left 1A11 Hardware kit 1
A5 Stationary handlebar cover,
right 1 A12 Glide rail covers 2
A6 Right roller cover 2 A13 French Sticker (For USA) 1
A7 Left roller cover 2

7
4. LIST OF PARTS (CONT.)
Components in the Hardware Kit
No. Name Qty. Specication Notes
10 Mushroom top inner hex screw 6 M10*P1.5*L20
Serrated washer 6 D20*d10.2*t2.0
11
Secondary guide roller bolt 2 D9.96*L54
Self-lubricating bushing 4
Secondary guide roller 2 D23*L45
12 Stride adjustment linkage cover 2
13 Hex nut 2 M10*P1.5
Stopper 2 Ø30-30
14 Phillips screw 4 M4*P0.7*L12
15 Mushroom top philips screw 9 M4*P0.7*L12
16 Phillips screw 2 M5*P0.8*L12
17 Phillips screw 2 M4*P0.7*L8
Ground wire 1 Yellow/Green
L1500
L-shaped Allen wrench 1 M4
L-shaped Allen wrench 1 M5
T-shaped Allen wrench 1 M6
Hex Phillips wrench 1 13*15
Double open-end wrench 1 14*15
Components on the Product
No. Name Specication Notes
31 Beveled head hex screw M10*P1.5*L20
32 Phillips screw M4*P0.7*L8
33 Phillips screw M4*P0.7*L14
34 Inner hex screw 5/16”*L2-1/4” half
Flat washer D20*d8*t2.0
35 Mushroom top inner hex screw M8*P1.25*L25
Handlebar washer D18*d8.5*t2
36 Inner hex screw M6*P1.0*L15
Handlebar washer D20*d7*t2
37 Mushroom top inner hex screw M6*P1.0*L15
Flat washer D13*d6*t1
38 Mushroom top philips screw M5*P0.8*L16

8
5. ASSEMBLE THE PRODUCT
Follow instructions below to assemble this product. Note that in this manual the words “left” and
“right” are used to refer to the product and its parts. As such, these designations correspond to
the “left” and “right” sides of a person in position to exercise on this product. Also, for brevity, the
word “screws” is used where screws, washers, and other hardware may be involved.
STEP 1 Install the Frame
Please follow instructions (a) through (h) to secure the pedestal.
(a) Remove the upper box and all packing material but leave the main frame (A1) in the lower
box for support.
(b) The screw A (10) is loosely attached before assembly. Raise the main post or pedestal into
position. Secure the pedestal hardware in sequence, rst D (31), then A (10), B and C (10)
as shown below.
(c) Then, raise the stride support Assembly (1) and pedal carriage (2). Place the tip of the food
pad surface on the ground (3). Do this step on the other side of the unit as well.
(d) Tip the frame slightly to access glide rail E.
1
10
10
31
2
3
A1
E
C
A

9
STEP 1 Install the Frame (CONT.)
(e) A: Once slip the glide rail into (Part A) and then place the pedal carriage lightly on the glide
rail support (Part B). Connect the guide roller on the bottom of the glide rail. (Please note
the direction to insert the screw is from outside to inside)
B: Unsecure the bolts (32) (33) from the left/right roller covers (A6) (A7) and then put the left/
right roller covers (A6) (A7) place and secure them (32) (33) as shown below.
Warning: Consult the manual and follow all assembly nstructions carefully. Please note that
incorrect assembly may present a danger to the exercise, will damage the elliptical
and void the warranty.
A
B
A7
A6
A6
A1
A1
33
32
11
a
b

10
STEP 1 Install the Frame (CONT.)
(f) Put the stride linkage in place and use the bolt (34) and washer to secure it onto the stride
support assembly and then press the stride adjustment linkage covers (12) into place as
shown below. Complete steps (d), (e), and (f) on the other side of the unit too.
2
1
A1
34 12

11
STEP 1 Install the Frame (CONT.)
(g) Secure stopper (13) on the front, bottom of both glide rails and then remove the unit from the
lower box.
13

12
STEP 1 Install the Frame (CONT.)
(h) (1) Loosely secure bolts (35) (36) A and B on both support tube (A8) (A9). At this point, do not
tighten these bolts.
(2) With hardware (37) shown in illustration I, secure the stationary handlebar (A2) at both sides
and then tighten bolts (35) (36) at area A and B.
(3) Secure the stationary handlebar covers (A4) (A5) with screws (14). When securing the
handlebar, make sure direction of screws (14) are 90-degree to the stationar handlebar (A2).
36
36
37
14
35
35
A8
A9
1. 2.
3.
A
A
B
B

13
STEP 2 Install the Glide Rail
Follow instructions (a) through (c) to install the glide rail.
(a) Move part (A) of the glide rail to the upper left part of the ywheel within the 90-degree
indication. Hook the part B onto the glide rail.
(b) Turn part B clockwise as shown to a nearly horizontal position of the glide rail covers (A12).
(c) Install part C onto part B. Use screws (15) (16) to fasten these parts together.
A12
A12
15
16
A
B
C

14
STEP 3 Install the Pedestal Covers
Hold the pedestal covers in place. Use the screw driver provided to tighten screws (15) into the
pedestal covers (A3).
A3
15

15
STEP 4 Install the Foot Pedals
Follow steps (a) through (b) to secure the support tubes.
(a) There are rubber pads (A) on the foot pedals (A10). Fold the rubber pad (A) up to access
screws. Secure the foot pedals (A10) onto the plate of main frame with screws (38) as
shown.
(b) Press the rubber pads (A) onto foot pedals (A10) rmly by Inserting the nibs on the rubber
pads (A) through the holes in the foot pedals (A10). Make sure that the nibs protrude through
the foot pedals (A10). (Please do not pull out the nibs in the middle.)
A1
A10
38

16
STEP 4 Install the Foot Pedals (Details)
Follow instructions (a) through (c) to install the details of the foot pedals.
(a) Make sure the middle nibs on the foot pedals (A10) are firmly placed into the middle holes on
the foot pedals (A10). Pull the nibs through the foot pedals (A10) until they fit snugly in place.
(b) Secure the front screws (shown as m1) on the foot pedals (A10). Insert the front nibs into the
holes on the foot pedals (A10) (shown as M). Pull the front nibs in place securely.
(c) Secure the back screws (shown as n1) on the foot pedals (A10). Insert the nibs into the holes
on the foot pedals (A10) (shown as N). Pull the nibs securely into place.
M
L
m1
n1
N

17
STEP 5 Level the Product
Please apply force to the end of the machine to check if the leveling knob is stable on the
ground. If not, adjust the levelers as follows:
(a) Loosen the leveling knob.
(b) Rotate the leveling knob downward to the ground to make it steady.
(c) Tighten the leveling knob.
(d) After the machine is installed and positioned, perform the test again. If necessary, make
adjustment to be sure the equipment works properly.
Space

18
STEP 6 Install the Ground Wire
Note: A ground wire and the following instructions are required by European safety standards.
The ground wire is not required by North American safety standards.
To avoid electric shock and current leakage, this product has an exterior ground wire. For your
safety, connect this ground wire to the unit and to the building ground. Installation instructions:
Please use screws and washers to secure one end of the ground wire to the product frame as
shown and the other end to the building electrical ground.

19
STEP 7 Unit Inspection
After completing the assembly, please follow instructions (a) through (b) below to inspect the unit.
(a) Before plugging the power cord, make sure the unit is steady and on a level surface. If the
unit is not steady, make adjustments according to the instructions “Level the product” of this
manual.
(b) After plugging the power cord, operate the control panel to test and ensure that the unit is
working properly. If the unit cannot be operated after the power on, please check the connection
and the fuse. Consult an experienced technician from SportsArt for help with any questions.

20
STEP 8 Beware of Moving Parts
This product has moving parts that could be a danger to people and animals. During use, do
not insert hands or other objects into the stride adjustment slot, the opening in the rear cover, or
other areas in which such action might present a hazard.