SportsArt Fitness MID ROW A921 User manual

A921
OWNER'S MANUAL
ASSEMBLY INSTRUCTIONS
MID ROW

A. SAFETY INSTRUCTIONS
Read all cautions/warnings and obtain proper instruction on use of the machines
prior to using. Use appropriate positioning and controlled movements.
Assemble and operate the strength on a solid, level surface. Do not use outdoors
or near water.
Never allow children on or near the strength.
Make sure all fasteners are properly tightened for safety. DO NOT use the
strength if the unit is disassembled in any way.
Keep head, limbs, and fingers clear of all moving parts.
If at any time during exercise you feel faint, dizzy or experience pain, stop and
consult you physician.
DO NOT wear loose or dangling clothing while using the equipment. Keep away
from all moving parts.
Use care when mounting and dismounting the unit.
DO NOT use any accessories that aren't specifically recommended by the
manufacturer. These might cause injuries or cause the unit to fall.
Close supervision is necessary when this strength is used by, on, or near
adolescent, invalids, and disabled persons.
Use this strength only for its intended use as described in this manual.
Never operate this strength if it has been damaged in any way. If it is not working
properly, been dropped or damaged, contact your dealer. DO NOT attempt to fix a
broken or jammed machine. Notify floor staff.
Never drop or insert any object into any opening.
1

2
B. Introduction
Front top cover
Grip
Hand arm
Connection host
Belt
Seat cushion and
adjustment handle
Foot pad
Side frame
Rear top cover
Front cover (A)
Support frame
Front cover (B)
Usage sticker
Back cover
Cord
Stack fork
Selection pin
Weight stacks (11 Lbs / 5 kgs)
Chest cushion
Selection pin (3.5 Lbs / 1.5 kgs)
Selection pin (6.5 Lbs / 3 kgs)

C. List of Parts
1. One connection host
2. One side frame
3. One support frame
4. Four hexagon socket raised head bolts, M8 x L20, for the seat cushion
5. Four spring washers, M8, for the seat cushion
6. Four hexagon socket counter-sunk flat-head bolt M8 x P1.25 x L20 for the seat plate
7. Four hexagon nylon nuts, M8, for the seat plate
8. Six hexagon head bolts, M10 x P1.5 x L30, ( 4 pcs for the connection host; 2 pcs
for the side frame and shoulder press set.)
9. Six spring washers M10 ( for connection host; for frame and shoulder
press set.)
10. Six nylon hex nuts, M10 x P1.5, ( for connection host; for the frame
and shoulder press set.)
11. One double-end open wrench, 17mm x 23mm
12. One double-end open wrench, 8mm x 17mm
13. One hex key wrench, M6
14. One hex key wrench, M5
15. User's manual
16. One double-end open wrench, 8mm x 10mm
17. One double-end open wrench, 12mm x 15mm
18.
4 pcs 2 pcs
4 pcs 2 pcs
Twelve washers, D16 x d10.2 x t1.0, (8 pcs for the connection host, 4 pcs for the
side frame and shoulder press set)
3

D. STEP BY STEP INSTRUCTION:
1. Fasten the seat plate with screws provided. (See Fig. 1)
2. Fasten the seat cushion in the plate with screws provided. (See Fig. 1-1)
4
Fig.1
Fig.1-1

3. For safety reasons, have three people assemble the machine. Then fasten the
vertical frame.
4. Hold the frame during assembly and tighten the connection host with the screws
provided. (See Fig. 2)
5. Hold the frame during assembly, then tighten the frame as shown in the diagram
with the screws provided. (See Fig.3)
5
Fig.2
Fig.3

6. Take out the wheel as shown in diagram A. Pull the belt through the gap and put
the wheel back in place. Then assemble the mechanism as shown in diagram B.
(See Fig.4-1)
7. Connect the belt and wheel as shown in diagram C. (See Fig.4-2)
6
diagram
diagram
diagram
Fig.4-2
Fig.4-1

Fig.5
7
E. BELT ADJUSTMENT:
1. If the belt is too tight or too loose, first loosen nut A as shown then adjust nut B. If
the belt length is too long, adjust downward; if the belt length is too short, adjust
upward. Adjust the belt to the proper position, then tighten nut A.
2. The gap between nut A and B must be within 35mm(1.4"). If the gap still
exceeds the 35mm limit after the first step, please loosen the screws on C
and adjust the belt to the proper length. Tighten the screws and follow the
1st step again. (See Fig. 5)

Fig.6
8
F. HOW TO USE THE MINOR WEIGHT STACK
1. To adjust the minor weight stack, insert the upper pin to add 3.5Lbs/1.5kgs
or the lower pin to add 6.5Lbs/3kgs.
2. Pull the pin to release the weight. (See Fig. 6)
3.5Lbs/1.5kgs
6.5Lbs/3kgs

9
Usage Instruction: