SportsArt Fitness 6200 Operating instructions

6200 Treadmill Repair Manual
SPORTS ART INDUSTRIAL CO., LTD.

SPORTSART INDUSTRIAL CO., LTD.
6200 Treadmill Repair Manual
Table of Contents
1. Treadmill Illustration
1-1-1 6200N Treadmill Illustration
2. Electronic Component Locations
2-1-1 6200N Treadmill Component Location Illustration – Upper Part
2-2-1 6200N Treadmill Component Location Illustration – Lower Part
3. Introduction
3-1-1 Model Introduction
3-2-1 Main Functions
3-3-1 Specifications
4. Product Operation
4-1-1 6200N Treadmill Operation
4-2-1 Display Function Modes
5. Unit Block Diagrams
5-1-1 6200N Treadmill Configuration
5-2-1 Display Board Wire Connections
5-3-1 Drive Board Wire Connections
6. Basic Connections
6-1-1 Display Board Wire Connections
6-2-1 Drive Board Wire Connections
0-0-1

SPORTS ART INDUSTRIAL CO., LTD.
6200 Treadmill Repair Manual
Table of Contents
7. Error Messages / Troubleshooting
7-1-1 6200/6200N/6260 Error Message: ERR 1
7-2-1 6200/6200N/6260 Error Message: ERR 3
7-3-1 6200/6200N/6260 Error Message: ERR 6
7-4-1 6200/6200N/6260 Error Message: ERR 7
7-5-1 6200/6200N/6260 Error Message: ERR 10
7-6-1 6200/6200N/6260 Error Message: ERR 11
7-7-1 6200/6200N/6260 Error Message: ERR 12
7-8-1 6200/6200N/6260 Error: Infrared Sensor is Not Picking Up a Signal
7-9-1 6200/6200N/6260 Error: Unit Doesn’t React When STOP Pad is Pressed
8. Incline Set Recalibration
8-1-1 6200/6200N/6260 Incline Set Recalibration Procedure
9. No Start – Transformer Test
9-1-1 No Start – Transformer Test
0-0-2

6200N Treadmill
1. Treadmill Illustration
SPORTS ART INDUSTRIAL CO., LTD.

SPORTS ART INDUSTRIAL CO., LTD.
6200N Treadmill Illustration
1-1-1

6200N Treadmill
2. Electronic Component Locations
SPORTS ART INDUSTRIAL CO., LTD.

SPORTS ART INDUSTRIAL CO., LTD.
2-1. 6200N Treadmill Component Location Illustration – Upper Part
2-1-1
Display
HTR Handlebar
Infrared Sensor
Filter

SPORTS ART INDUSTRIAL CO., LTD.
2-2. 6200N Treadmill Component Location – Lower Part
2-2-1
Drive
Board
Incline Motor & VR
Motor
Big Resistor
Optic Sensor &
Tachometer
Transformer
Inductor

6200N Treadmill
3. Introduction
SPORTS ART INDUSTRIAL CO., LTD.

SPORTS ART INDUSTRIAL CO., LTD.
3. Model Introduction
3-1. Introduction
6200N Treadmill is a club unit with microcomputer control. Functions include calorie and
distance count, heart rate, time, speed, and incline.
The 6200N Treadmill has a low speed of 0.2 KPH (0.1 MPH) and a high speed of 20.0 KPH
(12.0 MPH). In addition to forward motion, the 6200N Treadmill walk belt can also operate in
reverse, at speeds from a low of 0.2 KPH (0.1 MPH) to a high of 5.0 KPH (3.0MPH).
The 6200N Treadmill has an infrared sensor that detects whether a user is on the unit.
If no one stands on the treadmill, the display enters a wait mode. If the sensor detects a user,
the display goes into action.
The 6200N Treadmill has an advanced STOP touch switch. To stop the treadmill belt when in use,
lightly touch the STOP touch pad; the unit will stop all action.
The 6200N Treadmill simulates running on various incline surfaces. The highest incline level
is 22%, whereas the lowest level is -3% incline.
The 6200N Treadmill offers the use of two heart rate modes, the HTR handlebar and the POLAR
strap, both of which allow users to monitor their heart rate as they exercise.
3-1-1

SPORTS ART INDUSTRIAL CO., LTD.
2. Main Functions
2-1.Calorie Window Function
2-1-1. Shows the user calorie expenditure.
2-1-2. In Calorie expenditure countdown mode, at 0, the display “beeps” once.
2-2.Heart Rate Window Function
2-2-1. Shows the heart rate value.
2-2-2. Allows for use of the POLAR heart strap or built-in HTR handlebar.
2-3.Distance Window Function
2-3-1. Shows the distance covered by the user.
2-3-2. In Distance countdown mode, at 0, the display “beeps” once.
2-4.Time Window Function
2-4-1. Shows the length of time exercised.
2-4-2. In Time countdown mode, at 0, the display “beeps” once.
2-5.Speed Window Function
2-5-1. Shows the treadmill walk belt speed.
2-5-2. Treadmill walk belt speed setting ranges from a low speed of 0.2 KPH (0.1MPH)
and high speed of 20.0 KPH (12.0MPH).
2-5-3. Treadmill walk belt can operate in forward or reverse directions.
3-2-1

SPORTS ART INDUSTRIAL CO., LTD.
2-6.INCLINE Window Function
2-6-1. Shows incline position.
2-6-2. Incline setting is adjustable.
2-6-3. The highest incline setting is 22%; the lowest incline setting is -3%.
2-7. Infrared Sensor Function
2-7-1. Automatically detects whether a user is on the unit.
2-7-2. If no user is on the unit, the unit goes into “wait” mode; If a user is on the unit, all functions
are activated.
2-8. The TOUCH STOP Function
2-8-1. Lightly touch the STOP pad; The treadmill belt immediately stops operating.
2-8-2. A light touch is sufficient to operate the STOP function.
3-2-2

SPORTS ART INDUSTRIAL CO., LTD.
3. Specifications
Specifications Name Details Notes
Power Exterior Power Source: 110V or 220V
Window Functions CALORIES，HEARTRATE，DISTANCE
TIME，SPEED，INCLINE, etc., Function
Windows
Speed Modes Forward Motion; Reverse Motion
Speed Range Forward Speed 0.2 - 20.0 KPH or
0.1 - 14.0 MPH
Reverse Speed 0.2 – 5.0 KPH or
0.1 - 3.0MPH
Incline -3% to 22%
Sensor Infrared Sensor
STOP Switch Touch Stop Switch
Heart Rate Modes HTR Handlebar
POLAR Transmitter
KPH/MPH Setting Display Board Jumper Setting
CARDIO Function CARDIO Power Supply Socket
3-3-1

6200N Treadmill
4. Product Operation
SPORTS ART INDUSTRIAL CO., LTD.

SPORTS ART INDUSTRIAL CO., LTD.
6200N Treadmill Operation
1. Display Windows
4-1-1
Heart Rate Window
ÎHeart Rate Value
Calorie Window
ÎCalorie Display & Setting
Time Window
ÎTime Display & Setting
Incline Window
ÎIncline Position
Display & Setting
STOP Switch
ÎStop Function
Distance Window
ÎDistance Display & Setting Speed Window
ÎSpeed Display & Setting
STOP Switch
ÎStop Function

SPORTS ART INDUSTRIAL CO., LTD.
4-1-2 Soft Key Locations
4-1-2
SPEED Key
ÎSet Speed
CALORIE Key
ÎSet Calorie Goal
INCLINE Key
ÎSet Incline Position
DISTANCE Key
ÎSet Distance
TIME Key
ÎSet Workout Time
RESET Key
ÎClear Display

SPORTS ART INDUSTRIAL CO., LTD.
2. Display Function Modes
1. CALORIE Window Functions：
Functions：1. Displays user calorie expenditure value
2. Set calorie count value
Explanation：1. Display board CPU calculates calorie expenditure using factors including TIME, SPEED, WEIGHT.
2. When set to count down calories, the display “beeps” once when the calorie expenditure goal is reached.
Operation：1. Press SPEED<▲>/<▼> key to set the SPEED value. The calorie window shows the Calorie value.
2. Press the Calorie <▲>/<▼> key to set the Calorie value. The calorie window resets and the display
beeps once.
3. HEART RATE window function：
Function：1. Display the user heart rate.
Explanation：1. Once the heart rate is detected, the heart rate window shows the heart rate value.
2. There are two ways to detect heart rate: by use of the POLAR strap or by holding the Heart Touch Rate Bar.
Operation：1. The user straps on the POLAR heart rate transmitter and exercises within 100 cm
of the display. The heart rate window shows the heart rate value.
2.TheuserholdstheHTRbars,oneineachhand.Theheartratevalueappears
on the display.
4. DIST Window
Function：1. Display the distance covered by the user.
2.Caloriecountresetvalue.
4-2-1

SPORTS ART INDUSTRIAL CO., LTD.
Explanation：1. The display uses the TIME and SPEED value to calculate the distance.
2. When set to count down distance, the display makes a “beep”sound when
the distance value resets.
Operation：1. Press the Speed<▲>/<▼> keys to set the Speed value. In operation, the display
shows the distance covered.
2.PresstheDist<▲>/<▼>keys to set the distance countdown value. When the
distance window resets, the display makes a “beep” sound.
1. TIME Window
Function：1. Shows the length of time the user has exercised on the treadmill.
2.Setthetimecountresetvalue.
Explanation：1. The display automatically calculates the length of time in use.
2. In Time countdown mode, the display makes a “beep” sound
when the value resets.
Operation：1. Press the Speed<▲>/<▼> key to set the Speed value. In operation, the Time
window shows the length of the exercise time.
2. Press the Dist<▲>/<▼> key to set the Distance countdown value.
The display makes a “beep” sound when the Distance value resets.
2. SPEED Window
Function：1. Sets the treadmill speed.
2. Sets the direction of the treadmill walk belt.
Explanation：1. If the SPEED window shows a positive number, like “1.0” or “6.0”, the treadmill walk belt rotates for use in
a forward (not backward) direction.
2. In forward rotation, the speed range is 0.2-20.0 KPH or 0.1-12.0 MPH.
4-2-2

SPORTS ART INDUSTRIAL CO., LTD.
3. If the SPEED window shows a negative number, like “-1.0” or “–6.0”, the
treadmill operates for use in a reverse (backward) direction.
4. In reverse, the speed range is -0.2 to -5.0 KPH, or -0.1 to -3.0 MPH.
5.PresstheSPEED<▲>/<▼> key to set the SPEED value.
6. In reverse, the highest incline is 3%.
Operation：1. To change from forward to reverse operation,
(1) press the SPEED<▲> key until the SPEED window shows 0.2 KPH (or 0.1 MPH).
The treadmill walk belt moves slowly.
(2) Continually press the SPEED<▲> key until the SPEED window shows 20.0 KPH (or 12.0 MPH).
The treadmill operates at high speed.
(3) Continually press the SPEED<▼> key until the SPEED window shows 0.2 KPH (or 0.1 MPH).
The treadmill slows until the slowest forward speed is reached.
2.ReverseOperation
(1) Simultaneously press Calories <▼>+Distance<▼> keys twice. The display makes a “beep” sound; the
SPEED window shows “-0.0” to indicate reverse mode.
(2)PresstheSPEED<▲> key until the SPEED window shows “-0.2” KPH (or -0.1 MPH).
The treadmill belt moves in reverse at low speed.
(3)PressSPEED<▲> until the SPEED window shows “-5.0” KPH (or -3.0 MPH).
The treadmill belt operates in reverse at a higher speed.
(4)PresstheSPEED<▼> key until the SPEED window shows “-5.0” KPH (or -3.0 MPH).
The treadmill walk belt slows.
(5)ContinuouslypresstheINCLINE<▲> key. The INCLINE rises to the 3% position.
4-2-3

SPORTS ART INDUSTRIAL CO., LTD.
6. INCLINE Window
Function：1. Shows the present treadmill incline position.
2. Sets the treadmill incline position.
Explanation：1. The display automatically calculates the unit incline position.
2. Press the incline key to set the incline position.
3. Incline position ranges from -3% to 22%.
Operation：1. Press the INCLINE<▲> key until the INCLINE window shows 22%.
The unit incline rises to the highest position.
2. Press the INCLINE<▼> key until the INCLINE window shows 0%.
The unit incline falls to the level position.
3.PresstheINCLINE<▼> key until the INCLINE window shows -3%.
The incline falls to the lowest (a negative) position.
7. RESET Key
Function：1. Resets all display functions.
2. Clears all display windows to the 0 value, except for incline.
Explanation：1. Press the RESET key; the windows erase to 0, except for incline.
2. All display functions stop operating and reset.
Operation：1. Press the <RESET> key. The display makes a “beep” sound once.
Various windows flash. Display values clear to 0 (except for incline).
8. The Infrared Sensor Function
Function：1. Inspects whether anyone is standing on the treadmill before starting the display.
4-2-4