SportsArt Fitness T630 Operating instructions

T630 Treadmill Repair Manual
SPORTS ART INDUSTRIAL CO., LTD.

【Table of Contents】
1. Unit Components
1-1-1. T630 Product Picture
1-1-2. T630 Treadmill Components – (1) Display Area
1-1-3. T630 Treadmill Components – (2) Motor Area
1-1-4. T630 Display Components – (3) Display Board Front
1-1-6. T630 Display Components – Display Board Back
1-1-7. T630 Drive Board Components
1-1-8. T630 Display Components – Other
1-1-9. T630 Display Components – Other
2. Introduction
2-1-1. T630 Specifications
2-1-2. Introduction to the T630 Display
2-1-3. Display Indicators
2-1-4. Display Keys
3. Operation
3-1-1. T630 Operation – Start Up, Speed Key
3-1-2. Incline Key, Stop Key, Change Key
3-1-3. Clear Key, Program Key
3-1-4. Basic Settings: MPH/KPH; Basic Settings: Distance
0-0-1

【Table of Contents】
4. Block Diagrams
4-1-1. Display Board Cable Connections
4-2-1. Drive Board Cable Connections
5. Cable Connections
5-1.DisplayBoard
5-1-1. T630 Display Board Cable Connections
5-1-2. T630 Display Board Components
5-1-3. T630 Display Board LED Indicators
5-1-4. T630 Display Board Cable Connections
5-2. Drive Board
5-2-1 T630Drive Board Cable Connections
5-2-2. T630 Drive Board Components
5-2-3. T630 Drive Board LED Indicators
5-2-4. T630 Drive Board LED Indicators
5-2-5. T630Drive Board Cable Connections
5-2-6. T630 Drive Board Jumper Placement
0-0-2

【Table of Contents】
6. Error Messages
6-1-1. ERR1-Motor Does Not Rotate (Continued through 6-1-3)
6-2-1.ERR1-Motor Does Rotate (Continued through 6-2-3)
6-3-1. ERR3 (Continued through 6-3-3)
6-4-1. ERR7 (Continued through 6-4-3)
6-5-1. Display Key Malfunction (Continued through 6-5-2)
6-6-1. Unit Does Not Turn On (Continued through 6-6-3)
6-7-1.NoTelemetry Heart Rate (Continued through 6-7-3)
6-8-1. Incline Does Not Operate Up or Down (Continued through 6-6-2)
6-9-1.MainFuse Broke (Continued through 6-9-2)
6-10-1.Service Required (Continued through 6-10-2)
6-11-1.Heart Touch Rate Malfunction (Continued through 6-11-3)
7. Electronic Component Testing
7-1-1. EMI Filter Test
7-2-1.MotorTest
7-3-1.Transformer Test at the Drive Board
7-4-1.Inductor Test (220V units only)
7-5-1. Motor Voltage Test at the Drive Board
7-6-1. Drive Board IGBT Test
7-7-1. Drive Board VCC Test
0-0-3

【Table of Contents】
7-8-1 Drive Board Incline Motor Power Test
7-9-1 Incline Limiter Switch Test (Continued to 7-9-2)
7-10-1 Optic Sensor Signal Test - (Continued to 7-10-2)
7-11-1 Optic Sensor Signal Test – LED (Continued to 7-11-2)
7-12-1 Safety Key Test (Continued to 7-12-2)
7-13-1 AC Incline Motor Resistance Test (Continued to 7-13-3)
7-14-1 Keypad Test (Continued to 7-16-2)
7-15-1 Display Board VBB Circuit Test (Continued to 7-17-2)
7-16-1 Display Board VCC Circuit Test (Continued to 7-18-2)
7-17-1 Telemetry Heart Rate Test (Continued to 7-19-2)
7-18-1 HTR Board LED Indicators (Continued to 7-20-2)
7-19-1 7-21-1 HTR System Continuity Test
8. Mechanical Adjustments and Part Replacement
8-1. T630 Treadmill Walk Belt Tightness Adjustment
8-2. T630 Treadmill Walk Belt Alignment
8-3.AC Motor Incline Calibration Procedure - Software
8-4.AC Motor Incline Calibration Procedure - Hardware
0-0-4

1.T630 Product Picture
1-1-1

2.T630 Treadmill Components－(1) Display Area
Display
Key Pad HTR Handlebar (right)
HTR Handlebar (left)
1-1-2

3.T630 Treadmill Components－(2) Motor Area
1-1-3
EMI Filter
Motor
Optic Sensor
Calibration
Switch
Optic
Wheel
Drive Board
Incline Motor Transformer
Motor Thermal Sensor
Inductor

4. T630 Display
1-1-4

5.T630 Display Components – Display Board Front
1-1-5

6.T630 Display Components – Display Board Back
1-1-6

7. T630 Drive Board Components
1-1-7

8.T630 Display Components – Other
Part Key Pad Keys Part Optic Sensor
Part HRC Board
1-1-8

9.T630 Display Components - Other
Part HTR Boad Part EMI Filter
1-1-9

T630 Specifications
Specification NotesDetails
Power S Exter oupply i r Power Supply 110V (USA);
220V (Eu rope)
Main Win HRC hea
C
dow Display Rate, rt rate window: 65%, 80%, Heart
alories, Speed, Time, Distance,
Cal/hr, Mets, Pace, Incline
Seconda Dot Matriry Window
Display x 15 X 8 Window
Speed R 0.2 - 20.0
0.1 – 12.
ange KPH
0MPH
Incline R 0 % to 15 AC Moto
Program/
ange % r
Control
Heart Ra HTR Hea
eles
te Detection Wir rt Touch Rate (contact pads)
s Telemetry Heart Rate (HR
Transmitter)
KPH/MP Program H Setting
Operatio Manual,H
TEST,WT
n ill,Random,Interval,Track,FIT
Loss,Zone Trainer,FAT BURN,
Glute ,
2-1-1

T630 Introductions－Display Board
1. Display Window Introduction
65% Heart Rate Target
ÎShows 65% Heart
Rate Tar
g
et
80% Heart Rate Target
ÎShows 80% Heart
Rate Target
Dot Matrix
ÎWorkout
Illustrations
1. This LED flashes when
heart rate is detected.
HEART RATE Window
ÎShows Actual Heart Rate
Information
Window
ÎWorkout
Feedback
2-1-2

T630 Introductions－Display Indicators
Distance & Incline Window
ÎDistance lit = shows
distance
ÎIncline lit = shows incline
position
Speed & Mets
ÎSpeed lit = shows speed
ÎMets lit = shows METS value
Time & Pace Window
ÎTime lit = Exercise time
ÎPace lit = Pace value
Exercise Program Area
ÎLit = shows exercise
programs: Manual, Hill,
Random,Interval,Trcak,
FIT test, WT Loss,Zone
Trainer,FAT Burn,Glute
Calories & Cal/HR Window
ÎCalories lit = shows calories
expenditure
ÎCal/HR lit = shows Cal/HR
value
2-1-3

T630 Introductions －Display Keys
<CHANGE> Key
ÎPress to change
feedback information.
INCLINE<▲>/<▼> Key
ÎPress to set incline position.
SPEED<▲>/<▼> Key
ÎPress to set unit speed.
<MANUAL><HILL><RAND
OM>< INTV > <Track>
<FIT Test><WT LOSS>
<ZONE TRAINER>
<FAT Burn><GLUTE >Keys
ÎPress to choose an
exercise program.
＜QUICK START＞Key
ÎPress to start without
inputting user
information.
<START> <QUICK START> <ENTER> Key
ÎPress Start to start. Press Quick Start to start without
entering user information. Press ENTER to confirm your
choice.
<1>~<9> and
<CLEAR> Keys
ÎPress to directly set
numerical values or
to clear settings. It
replaces the ▲▼
keys.
＜STOP＞Key
ÎPress to stop operation.
2-1-4

T630 Operation
1. Start Up
Function: Press the Quick Start key to start operating the unit.
Operation: (1) The display shows “SPORTSART – T630”.
After two seconds, “SELECT PROGRAM OR QUICKSTART” scrolls across the display.
Press the QUICK START key to start operating or press the PROGRAM key to operate
an exercise program.
(2) The PROGRAM LED flashes
After pressing a program key, the associated program indicator lights up.
The setting window shows two seconds. If you press the <RANDOM> key,
the RANDOM LED lights. “RANDOM” appears.
(3) User age and weight setting
When “AGE – 35”appears, press the numerical keys or INCLINE▲/▼.
Then press the <ENTER> key to confirm your setting.
When “WEIGHT -- 75
KG” appears, press the numerical keys or INCLINE▲/▼.
Then press the <ENTER> key to confirm your setting.
(4) After entering such information, you can start operating the treadmill.
2.SPEED Key
Function: Set speed function
Operation: (1) Press the SPEED <▲> key. Values in the speed window increase.
Speed increases.
(2) Press the SPEED <▼> key. Values in the speed window decrease. Speed decreases.
(3) SPEED range: 0.2~20 KPH (0.1~12 MPH).
3-1-1

3.INCLINE Key Function
Function: Set treadmill incline position.
Operation: (1) Press the INCLINE<▲> key. Values in the incline window increase.
Incline operates up.
(2) Press the INCLINE<▼> key. Values in the incline window decrease.
Incline operates down.
(3)INCLINE range: 0~15％; increments of 0﹒5％.
4.STOP Key Function
Function: Leave an exercise program.
Operation: (1) In QUICKSTART mode, press the＜STOP＞key to leave the exercise program.
(2) If in the START mode, having entered user information, press the＜STOP＞key to
stop exercising. Feedback pauses
as is.
(3) In any mode, hold the＜STOP＞key three seconds to leave the present mode
and return to start up screen.
5.CHANGE Key Function
Function: Change the display feedback row.
Operation: (1) Press the <Change Display> key while exercising to toggle from one
feedback row to another feedback row. Corresponding LEDs light. Top row:
CALORIES、SPEED、TIME、DISTANCE. Bottom row: CAL/HR、METS、PACE、INCLINE.
(2) In SCAN mode, the SCAN LED lights. Every four seconds, the display toggles
from one feedback row to the other row. If you press the SCAN key again, the
scanLEDextinguishes. The display continues to show the activated feedback row.
3-1-2