Spring V11M BPC User manual

Connect the pump
controller following
this diagram and the
Fitting Instructions.
Wiring Diagram
Mains Pump Controller - Quick Start V11M
BPC
Connect your
230Vac mains
powered pump
by plugging in
to this socket.
Step 1. Fitting Instructions
This V11M BPC FM unit is supplied already wired. There is
no need to disconnect any wires. Follow these instructions
carefully and refer to the wiring diagram.
IT IS RECOMMENDED THAT YOUR V11M IS FITTED AGAINST
A WALL OR SIMILAR VERTICAL SURFACE.
1. Ensure the V11M is NOT PLUGGED into the MAINS SUPPLY.
2. Remove the top cover by loosening the four corner screws. Using
a large pozidrive screw driver continuously turn counter clockwise.
3. Carefully remove the top cover.
4. Screw unit to the wall or vertical surface through the four ready
drilled holes in the corners of the back box.
5. Carefully replace the top cover and tighten the four corner
screws, using the reverse procedure to instruction 2. above.
You are now ready to control your pump.
NOTE: Only switch on MAINS SUPPLY to the 230Vac 5A Mains Plug
once front cover has been re-fitted.
DISCLAIMER
Unit must be installed by a competent electrician or electrical engineer. Failure
to comply with these instructions could invalidate your warranty.
ALWAYS DISCONNECT THE MAINS SUPPLY
BEFORE OPENING UNIT.
ALWAYS DISCONNECT THE MAINS SUPPLY
BEFORE CONNECTING THE PUMP
!
ALWAYS DISCONNECT
THE MAINS SUPPLY
BEFORE OPENING UNIT.
!
230Vac
5A
Mains
Plug
High
Level
Switch
RO Inlet
(Fill) Valve
Yellow
Grey
230Vac
Pump
Mains
Socket
Outlet

Mains Pump Controller - Quick Start V11M
BPC
Step 1. Fitting Instructions
DISCLAIMER
Unit must be installed by a competent electrician or electrical engineer. Failure
to comply with these instructions could invalidate your warranty.
ALWAYS DISCONNECT THE MAINS SUPPLY
BEFORE OPENING UNIT.
ALWAYS DISCONNECT THE MAINS SUPPLY
BEFORE CONNECTING THE PUMP
!
230Vac
5A
Mains
Plug
WATER
IN
FILL
MANUAL FLOW
RESTRICTOR VALVE
WASTE
RO
FILTER
SEDIMENT
+ CARBON
FILTERS
FILLING
SOLENOID
VALVE
WATER TANK
HIGH LEVEL
SWITCH
OPTIONAL
TDS
DI
VESSEL
BOOSTER
PUMP
230Vac
Pump
Mains
Socket
Outlet

Mains Pump Controller Quick Start Guide V11M BPC
Step 2. Set Up - Power Up and Filling Step 2. Continued
This message will display if the PSU develops
a fault. If voltage drops below 10.5V the unit will
shut down the pump.
Message Description
If the unit is a 'One time fill' then pressing the up and down
arrows together and holding will stop the fill.
When the tank is full enough to activate the float switch,
the controller stop the fill. The booster pump is stopped,
the filling solenoid valve is closed. The controller will go
back to displaying the PSU voltage.
If your V11M is configured as a 'Fill on Demand' unit then
filling will start automatically as soon as the float switch
is in the down (normally closed) position.
The controller will turn on the filling solenoid valve and the
mains booster pump connected to the mains socket outlet.
This should allow water to fill your tank at a boosted
pressure by the mains booster pump.
On first power up the controller displays the voltage of the
PSU in volts. It should be 12V (+/- 0.2V).
Turn on the controller by pressing the up or down button.
Keep the button held until the display lights up.
Connect your pump and liquid system to be controlled.
The controller is filling the tank. Booster pump
and solenoid filling valve are on.
If your V11M is configured as a 'One time fill' unit then
filling will start when you press and hold the up and down
arrows at the same time.
+
+