Spring V11M User manual

Connect the pump
controller following
this diagram and the
Fitting Instructions.
Wiring Diagram
Mains Pump Controller - Quick Start V11M
BPC FM
Connect your 230Vac mains
powered pump by plugging in
to this socket.
Step 1. Fitting Instructions
This V11M BPC FM unit is supplied already wired. There is
no need to disconnect any wires. Follow these instructions
carefully and refer to the wiring diagram.
IT IS RECOMMENDED THAT YOUR V11M IS FITTED AGAINST
A WALL OR SIMILAR VERTICAL SURFACE.
1. Ensure the V11M is NOT PLUGGED into the MAINS SUPPLY.
2. Remove the top cover by loosening the four corner screws. Using
a large pozidrive screw driver continuously turn counter clockwise.
3. Carefully remove the top cover.
4. Screw unit to the wall or vertical surface through the four ready
drilled holes in the corners of the back box.
5. Carefully replace the top cover and tighten the four corner
screws, using the reverse procedure to instruction 2. above.
You are now ready to control your pump.
NOTE: Only switch on MAINS SUPPLY to the 230Vac 5A Mains Plug
once front cover has been re-fitted.
DISCLAIMER
Unit must be installed by a competent electrician or electrical engineer. Failure
to comply with these instructions could invalidate your warranty.
ALWAYS DISCONNECT THE MAINS SUPPLY
BEFORE OPENING UNIT.
ALWAYS DISCONNECT THE MAINS SUPPLY
BEFORE CONNECTING THE PUMP
!
ALWAYS DISCONNECT
THE MAINS SUPPLY
BEFORE OPENING UNIT.
!
230Vac
Pump
Mains
Socket
Outlet
230Vac
5A
Mains
Plug
High
Level
Switch
RO Inlet
(Fill) Valve
Yellow
Grey
Flowmeter
Inline
Connector

Mains Pump Controller - Quick Start V11M
BPC FM
Step 1. Fitting Instructions
DISCLAIMER
Unit must be installed by a competent electrician or electrical engineer. Failure
to comply with these instructions could invalidate your warranty.
ALWAYS DISCONNECT THE MAINS SUPPLY
BEFORE OPENING UNIT.
ALWAYS DISCONNECT THE MAINS SUPPLY
BEFORE CONNECTING THE PUMP
!
230Vac
Pump
Mains
Socket
Outlet
230Vac
5A
Mains
Plug
WATER
IN FLOW
METER
FILL
INLINE
CONNECTOR
MANUAL FLOW
RESTRICTOR VALVE
WASTE
RO
FILTER
SEDIMENT
+ CARBON
FILTERS
FILLING
SOLENOID
VALVE
WATER TANK
HIGH LEVEL
SWITCH
OPTIONAL
TDS
DI
VESSEL
BOOSTER
PUMP

Mains Pump Controller Quick Start Guide V11M BPC FM
Step 2. Set Up - Power Up and Filling Step 2. Continued
The flowmeter has detected no flow and the unit
has stopped the fill to protect the booster pump.
This message will display if the PSU develops
a fault. If voltage drops below 10.5V the unit will
shut down the pump.
Message Description
,
There is no water flowing, the filling has been paused. If
the water starts to flow again the booster pump is turned
back on and the boosted filling restarts.
When the tank is full enough to activate the float switch,
the controller will display 'FUL' and stop the fill. The booster
pump is stopped, the filling solenoid valve is closed.
Press up and down to start a fill.
The controller will turn on the filling solenoid valve. After
10 seconds the unit will turn on the mains booster pump
connected to the mains socket outlet.
The unit will display the water flowrate (rtE) into the RO,
as measured by the flowmeter.
(Note: If the flowmeter detects no flow within 5 seconds
of starting a fill the unit will shut down booster pump
connected to the mains socket outlet. If there is still no
flow after a further 5 seconds the filling solenoid valve is
closed and the fill is stopped).
If the mains water supply should fail and no water is
flowing the controller will pause the fill by stopping the
booster pump, but will keep the filling solenoid valve open.
+
On first power up the controller displays the flow rate in
litres per min (LPM). It should be zero.
Turn on the controller by pressing the up or down button.
Keep the button held until the display lights up.
Connect your pump and liquid system to be controlled.
The flowmeter rate in litres/minute is being
displayed.
The controller is filling the tank. Booster pump
and solenoid filling valve are on.
The tank is full, the level switch has activated
filling has stopped.