Sproutwell Small Circle User manual

MODEL:Small Circle
PRODUCTSIZE(LxWxH):320x283x275cm
PLEASEREADCAREFULLYBEFOREASSEMBLY
Assembly Instructions
Small Circle Greenhouse

CONTENTS
1. Assembly Advice ................................................................Page 1
2. Product Features ................................................................Page 2 - 3
3. Part Lists .............................................................................Page 4 - 7
4. Roof Vents Assembly ..........................................................Page 8 - 12
6. Doors Assembly ..................................................................Page 13 - 16
7. Base Assembly ....................................................................Page 17 - 18
8. Framework Assembly ..........................................................Page 19 - 39
9. Panels Assembly .................................................................Page 40 - 49

11
Free ToolFree ToolFree ToolFree Tool
Assembly and Maintenance Advice
Tools Provided:
Component required but not provided:
Neutral Silicone Sealant
Tools Required when Assembly (Not Provided)
Assembly at least by two Persons
1. For safety purposes, we strongly recommend that the product will be assembled by at least two people.
2. Some parts have sharp edges. Please be careful when handling components. Always wear gloves, shoes
and safety goggles during assembly.
3. DO NOT climb or stand on the roof, heavy articles should not be leaned against the greenhouse.
4. Keep roof and gutter clean of snow,dirt & leaves. Large amounts of snow on roof can damage the product,
making it unsafe to stand below or nearby.
5. When your product needs cleaning, use a mild detergent solution and rinse with cold clean water.
Do not use acetone, abrasive cleaners or other special detergents to clean the panels.
(Suitable for Polycarbonate)

2
30mm 120mm 71mm
72mm
83mm
8&10mm 8&10mm
8&10mm
(8/10mm)PCPanel
4&6mm 4&6mm
4&6mm
(4/6mm)GlassPanel
* If you are glazing this greenhouse with glass you will need to slide the rubber gaskets
(provided) into the bar capping.
Functions and Features:
1. Compared with traditional greenhouses, this exciting new product features many significant
improvements. The hollow box profile aluminium framing is much stronger than other
greenhouses and it can withstand much greater wind loads.
Gutter Profile Post
Traditional Greenhouse New Circle Greenhouse
2. These greenhouses can be glazed with glass or polycarbonate of varying thicknesses.

Expansion
screw/Concrete
ground
3
3. Base anchor brackets are included as standard with expanding bolts to ensure a secure
fixing into concrete or paving. Alternatively, you can use the brackets to fix into a
timber base with wood screws.
5. The strong two part eaves include a gutter. Downpipes are also included
7. Remove approximately 2 inches of film from all sheet edges before installing and remove
all film immediately after the construction is completed. Please ensure that the side
with the white film faces outwards.
6. Automatic Roof Cap. The roof cap can open or close automatically.
4. Our unique frame connectors (2.5mm thick) make much stronger joints than conventional
greenhouses.
Steel bar/Lawn land
We recommend a timber plinth be used and secured to
the earth with metal star pickets.
as standard so you can collect rainwater.

4
PART NO QTY
L08A 5
L10 1
J01 6
L01A 6
L07 6
B6
J02 6
3
S01
M6X12
A6
ALU. Box No. 1
ALU. Box No.1

5
ALU. Box No.2
ALU. Box No. 2
PART NO QTY
L02A 6
L23A
12
L23B
14
L23C 35
K34
L23D 44
L02K 11
1
W01
W11 6
S01
M6X12 6
M03
M6 6
6
L03A

6
PART NO QTY
L11B 12
2
L12C
4
L12D
L09 6
2
L22
W08 2
4
4X10
Z03
S01
M6X12
Z4
L11A 11
L11D 10
11
L12K
6
L12A
L11E 1
L14 1
M03
M6
W03 2
4
4X14D
Z02
J06 6
J07 6
J08 6
6
4X14
Z01
PART NO QTY
L19A 4
L19B 2
L20 2
L11F 4
L11G 4
W06 2
J8
4
Z03
4X10
Windowx2pcs PART NO QTY
Door
PART NO QTY
S03 11
M8X60
W05 11
L16A 4
L17 1
L18A 1
L16B 4
L18C 1
L18D 2
L11H 4
L11J 4
4
4
4X40
Z04
D2
S02 2
M8X30
M02
M8 2
J
L02B 4
L02C 2
L02D 4
L02E 2
L24A 6
L24B 4
L24C 8
1
W04 1
L24D 4
L25A 4
L25B 4
L25C 2
L25D 4
L25E 2
4
L12B
L04A 1W02 1
W09 2
S04 2
M8X150
K14
W11 6
N4
PART NO QTY
10
13
M01
M6 3
ALU. Box No.3
Base
ALU. Box No. 3
Auto
Opener

PC/Glass
7
PART NO QTY
Y1 2
Y2 2
Y3 2
Y4 2
Y10 2
Y11 2
Y6 22
Y5 4
Y13 4
Y6
Y6
Y6
Y6
Y1 Y2
Y3
Y10
Y4
Y6
Y6
Y6
Y6
Y1 Y2
Y3 Y10 Y4
Y5
Y11
Y11
Y13
Y6
Y6
Y5
Y6
Y6
Y13
Y6
Y6
Y5
Y6
Y6
Y13
Y6
Y6
Y5
Y6
Y6
Y13
Y6
Y6
PC/GLASS. Box

PART NO QTY
L19A 4
L19B 2
L20 2
L11F 4
L11G 4
W06 2
J8
8
L20
L19B
L19A
L19A
B
B
B
B
Y10
L11F L11F
L11G
L11G
W06
4
Z03
4X10
Y10 2
Roof Vents Assembly 2PCS
Aluminium Capping
Panels
Frames

9
L20
L19B
L19A
L19A
J
J
J
J
1
1
2
2
L20
J
L19A J
L19A
L19B
1
2
Push down the button on
connector J before inserting it
into the end of the frame profile.
After connector J has been fitted,
use the hole in the profile to tighten
the connector in place.

10
L11G
L11G
L11F
L11F Y10
Y10
First the glazing panel Y10 should be loosely retained by the bar capping profiles
L11F and L11G. Next tap the bar capping gently into position with a rubber mallet.
L11F L11F

11
Z03 Z03
W06
Y10
Y10
Fix the W06 vent handles using Z03 screws.

12
Y10
Fill the gap with silicone sealant on 4 sides to avoid any leaking.

PART NO QTY
L16A 4
L17 1
L18A 1
L16B 4
L18C 1
L18D 2
PART NO QTY
4
PART NO QTY
Y11 2
4
4X40
Z04
D2
S02 2
M8X30
M02
M8 2
13
L11H 4
L11J 4
J
Door Assembly

14
L16A&B
L18A&C&D
L17
L16A
L16A
1
2Z04
L18A/L18C
L16B
L17
L16A
L16A
L18D
L16A
L16A
L16A
L16A
L17
L16B
L16B
L18D
J
J
J
J
L18C
S02x2pcs
L18D
1
1
1
1
22
L18A
then assemble the door frames using connector J, as shown in the
sketches below.
Put L16A into L17 and L18D and put L16B into L18A and L18C,
Push down the button on
connector J before inserting it
into the end of the frame profile.
Tighten L17 through
L18A/L18C with Z04.
After connector J has been fitted,
use the hole in the profile to tighten
the connector in place.

15
Y11 Y11
Y11
Y11
L11H
L11H
L11H
L11H
L11J
L11J
First the glazing panels should be loosely retained by the bar capping profiles L11H and L11J.
Next tap the bar capping gently into position with a rubber mallet.

16
M2
H100mm 100mm
29mm 29mm
11
11
After Assembly
* This is the method of
adjusting the door height.
Slide 2xS02 into L18D, positioned 100mm away from each edge.
Secure S02 using M02 bolts, then rotate the wheels
to ensure free movement.

17
ab
=
abc
=c
abc
It is essential the dimensions a = b = c are the same to ensure the base is square.
Expansion bolt
in concrete
Support at the corners only is inadequate.
Steel pegs in soil
We recommend a timber plinth be used and secured to
the earth with metal star pickets.

18
106.3
395
PART NO QTY
S03 11
M8X60
W05 11
395
395 395
395395
395
395
395
395 395
2762.1mm
L10
63.7mm
2634.7mm
2804.7mm
3042.3mm
1594.7mm
3189.4mm
106.3mm
This shows the outer & inner dimensions
of this product which helps build up the
optional bases.
Base Set Up
Assembly of W05 and dimensions