Sproutwell SMALL GAZEBO User manual

MODEL:
PRODUCTSIZE(LxWxH):295x295x270cm
PLEASEREADCAREFULLYBEFOREASSEMBLY
SMALL GAZEBO
Assembly Instructions
Gazebo Glasshouse

2
FreeTool
Assembly and Maintenance Advice
1. For safety purposes, we strongly recommend that this product is assembled by at least
two people.
2. Some components have sharp metal edges. Please be careful when handling metal
components. Please wear gloves, shoes and safety goggles during assembly.
3. Lay all of the components on a soft carpet or blanket to avoid any scratches or damages.
4. DO NOT climb or stand on the roof. Heavy articles should not be leaned against
the greenhouse.
5. Keep the roof and gutter clear of snow, dirt & leaves. Allowing snow to build up on
the roof may damage the product.
6. Unlike steel, if the paint finish is scratched this will not harm the aluminium underneath.
7. When your product needs cleaning, use a mild detergent solution and rinse with cold
clean water. Do not use acetone, abrasive cleaners or strong detergents to clean
the panels.
Tools Provided:
Assembly at least by two Persons
Rubber Sealing is ONLY provided for Glass Panels.
IMPORTANT:
Tools Required during Assembly (Not Provided)

3
2. Base anchor brackets are included as standard with expanding bolts to ensure a secure
fixing into concrete or paving. Alternatively, you can use the brackets to fix into a
timber base with wood screws (not provided).
Expansion bolt
in concrete
Functions and Features:
1. Compared with traditional greenhouses this new product features many significant
improvements. The hollow box profile aluminium framing is much stronger than other
greenhouses and it can withstand much greater pressure.
3. Our unique frame connectors make much stronger joints than conventional greenhouses.
4. The strong two part eaves beam includes an integral gutter. Downpipes are also included
as standard so you can collect rainwater.

4
Automatic Opener
Manual Opener
5. Manual window handles are included as standard with the roof vents. If required,
automatic roof vent openers are available as an inexpensive optional extra.
6. Each Polycarbonate Panel comes with UV protected properties.
Please ensure the clear film with the text faces out, toward the sun.
Remove both films before installation of the panels.

PLEASE NOTE:
We have recently changed our polycarbonate
film. All panels must be installed with the white
film facing inside and the clear film with writing
facing the sun.
If you have any questions please feel free to
contact us.
Head Office: Mon-Fri 9am-4pm
14 Crown Street
South Geelong, VIC 3220
PH: 1300 657 174
[e-mail]
POLYCARBONATE ORIENTATION
WRITING
FACES THE
SUN
X
5

6
PART NO QTY
L01A 4
1
1
L04A
L04B
3
L05A
L08A 4
4
L09A
4
L07A
L23A 4
B8
8
W07
4
4X14D
Z02 175
M4.2X16
Z01
J01 4
J02 4
4
W03
W08 2
W21 4
4
W22
1
W23
1
W24
W05 14
J06 4
J07 4
J08 4
L25 4
202
M5X12
S01
26
M5X12
S02
8
M4.2X16
Z03
M8
M01 2
W06 2
S03 14
M8X60
PART NO QTY
4
L05E
1
L05F
S04
M6X12 6
6
M02
M6
A8
SMALL GAZEBO (ALU Box No. 1)
ALU Box No. 1

7
PART NO QTY
L19A 4
L19B 2
L20 2
L11 2
L15A 2
PART NO QTY
4
L03D
4L05C
2
L05B
2
L02E
1
L24
PART NO QTY
L03A 9
L16A 1
L18A 2
L18B 2
1
L18C
1
L18D
L17 2
L05G 4
L16B 1
L03B 4
4
L03C
ALU Box No. 2
Door Assembly Vent Assembly x 2
SMALL GAZEBO (ALU Box No. 2)

8
PART NO QTY
Y10 2
Y11 4
Y5 12
Y5
Y5
Y5 Y1
Y3
Y4
Y2
Y5 Y5
Y5
Y5
Y5
Y5
Y5
Y5
Y5
Y1
Y1
Y1
Y3
Y3
Y3
Y4
Y4
Y4
Y6
Y6
Y7
Y7
Y10
Y10
Y11 Y11
Y11Y11
4
4
Y2
Y1
Y3
Y4
4
4
Y6 2
Y7 2
PART NO QTY
126M
J11
PART NO QTY
79M
J11
PC/Glass
NO.1
Rubber Sealing for Walls & Roof
(Provided for Glass Panels only)
Rubber Sealing for Walls Only
(Provided for Glass Panels only)
(PC/Glass Box No. 1)
SMALL GAZEBO

PART NO QTY
L19A 2
L19B 1
9
Y10 1
L20 1
10
M4.2X16
Z01
L19A
L19A
L19B
L20
Y10
W07
BW07
W07
W07
B
B
B
W07
B
Z01
20MM
20MM
20MM
B4
4
W07
0 1 2 3
Z01
L19B
W06
W06 1
W06
Vent Assembly
322MM 322MM
Install Vent Arm W06 in the middle
of L19B, 322mm from each end.
Screws position
Screws position
Insert Connector B & W07 into each end of
the profiles L19A & L19B & L20, and then
* Please ensure there is no gaps between each profile.
mark the distance from each end about 20MM.
Lastly, secure them with screws Z01.

PART NO QTY
L11 1
L15A 1
10
2
M4.2X16
Z01 L11
L15A
1
1
22
Z02
Z01
2
4X14D
Z02
Y10
J11
J11
PART NO QTY
2.65M
J11
1
2
Insert the Rubber J11 between Glass panels and Profiles
as shown below (Not Provided for PC panels).

11
Z01
Z01
0 1 2 3
20MM
30MM
A
PART NO QTY
L16A 1
L18A 2
L18B 2
1
A8
10
M5X12
S01
L18C
1
L18D
32
M4.2X16
Z01
L17 2
Y11 4
S04
S04
M02
M02
L05G
L05G
AA
A
A
L16B
L18D
L18A
L18B
Y11
Y11
S04
M6X12 6
6
M02
M6
L05G 4
S01
L16B 1
Left Door Assembly
1
1
2
L17
Insert Connector A into each end of
the profiles L16B & L18A & L18B &
L18D, and then mark the distance
Lastly, secure them with screws Z01
using the powered screw-driver.
from each end about 20/30MM.
12

12
Z01
Z01
0 1 2 3
20MM
30MM
L18A
L18B
L18C
L16A
A
A
A
A
L05G
L05G
L17
Y11
Y11
S04
S04
M02
M02
S01
Right Door Assembly
1
1
2
Insert Connector A into each end of
the profiles L16A & L18A & L18B &
L18C, and then mark the distance
Lastly, secure them with screws Z01
using the powered screw-driver.
from each end about 20/30MM.
12
A

13
PART NO QTY
12.2M
J11
J11 J11
Y11
Insert the Rubber J11 between Glass panels and Profiles
as shown below (Not Provided for PC panels).

ab
ab
=
ab
ab
=
14
10mm
It is essential the dimensions a + b are the same to ensure the base is square.
Support at the corners only is inadequate.
Expansion Screw
/ Concrete Ground

15
10mm
PART NO QTY
S03 14
M8X60
W05 14
2899MM (inner)
2899MM (inner)
4100MM (inner)
Door
352
705705705
352
352
705
705
352
352 352
352
705
705
352
705 705
0 1 2 3
25
2949MM (outer)
2949MM (outer)
4170.5MM (outer)
Expansion bolts assembly
Door
* This shows a layout for W05's positions where it is placed
in the middle of the panel for each section.

PART NO QTY
L08A 4
16
J02 4
L08A
J02
L01A 4
L08A
L08A
L08A
L08A
J02
J02
J02
J02
0123
0 1 2 3
L01A
8
M5X12
S01
L01A
L01A
L01A
L01A
S01
Insert the J02 into L08A as shown.
Install L01A onto each L08A through
the J02 using the screw S01.

PART NO QTY
17
4
L07A L07A
L07A
L07A
J01
J01
J01
J01
J01
L07A L07A
L07A
0123
0 1 2 3
S01
8
M5X12
S01
J01 4
Insert the joint J01 into L01A from the top, then connect each L07A ;
Lastly, secure all parts using the screw S01.
* Please ensure all parts are in correct angle before tightening up screw S01.

PART NO QTY
L03A 3
18
4
12
M5X12
S01
Y5
Y5
Y5
Y5
L03A
L03A
L03A
Y5
L07A
L08A
S01
S01
Back Wall Assembly
The last panel
and then install L03A. Secure them with screw S01.
Lastly, slide the last Panel Y5 from the top into
But if using PC Panels, you can install all the L03A firstly,
and then slide PC Panels in.
Insert the first Panel Y5 into the channel of L01A,
Do the same for another 2 sections.
the channels of L01A & L03A as shown below.
* This shows the correct way to install Glass Panels.

PART NO QTY
L03A 6
19
6
24
M5X12
S01
Y5
L03A
L03A
L07A
L08A
Y5 Y5 Y5
Y6
Y6
2
Y6
L03A
L03A
S01
S01
The last panel
Side Wall Assembly
Repeat the sequence as per
Y6 is the last panel to slide in.
the Back Wall Assembly,

PART NO QTY
1
20
1
2
Y5
Y5
L04A
L04B
L04A L04B
L05B
L05B
L07A
L08A
L04A/L04B
L04A/L04B
L05B
L05B
L04A/L04B
L01A
L05B
S01 S01
S01
S01
16
M5X12
S01 2
Y5
Do the same as Back Wall Assembly
Front Wall Assembly
to install L04A & L04B and Y5 using
the screw S01.
Then install L05B onto L01A & L04A
& L04B using the screw S01.