SPYKER SPY200T-1P User manual

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 1 1019884-B
Spyker Spreaders
Contact us at 800.972.6130
www.spyker.com
!IMPORTANT
This manual contains information for the safety of persons and property.
Read it carefully before assembly and operation of the equipment!
OPERATOR'S MANUAL
Model SPY200T-1P Tow Spreader

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 2 1019884-B
Introduction
USING YOUR OPERATOR’S MANUAL
Read this entire operator’s manual, especially
the safety information, before operating.
This manual is an important part of your machine. Keep all
manuals in a convenient location so they can be accessed
easily.
Use the safety and operating information in the attachment
operator’s manual, along with machine operator’s manual, to
operate and service the attachment safely and correctly.
Some machine preparation may be necessary for your tractor
or vehicle before you can install the attachment. The
assembly and installation sections of this manual provide
information to assemble and install the attachment to your
tractor or vehicle. Use the service section to make any
needed adjustments and routine service to your attachment.
If you have any questions or concerns with the assembly,
installation, or operation of this attachment, please call
1-800-972-6130.
Warranty information on this Spyker attachment can be found
in the warranty statement included in this manual.
TABLE OF CONTENTS
Intro / Safety . . . . . . . . . . . . . . . . .2-3
Part List . . . . . . . . . . . . . . . . . . . . . 3
Hardware Identier . . . . . . . . . . 4-5
Part Explosions . . . . . . . . . . . . . 6-8
Assembly . . . . . . . . . . . . . . . . . 9-14
Operation Instructions . . . . . . 15-23
Specifications / Before Operating . . . . . 15
Installing / Removing . . . . . . . . . . . . . . 16
Flow Control / Settings . . . . . . . . . . . . . 17
Spreading Tips . . . . . . . . . . . . . . . . 18-20
Cleaning / Maintenance . . . . . . . . . 21-22
Storage . . . . . . . . . . . . . . . . . . . . . . . . 22
Setting Charts . . . . . . . . . . . . . . . . . . . 23
Warranty . . . . . . . . . . . . . . . . . . . . 24
Original instructions. All information, illustrations and specifications in this manual are based on the latest information available at the time of
publication. The right is reserved to make changes at any time without notice.
SPY200T-1P
Product
Compatibility
Compatible with Lawn
and Garden Tractors

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 3 1019884-B
OPERATE SAFELY
Read Before Using:
• Use this machine for intended purpose only.
• Keep bystanders away when you operate this machine.
• Do not let children or an untrained person operate machine.
• Keep all parts in good condition and properly installed. Fix
damaged parts immediately. Replace worn or broken parts.
• Do not modify the machine or safety devices. Unauthorized
modications to the machine may impair its function and
safety, and void the warranty.
• Do not let anyone sit or ride on the equipment during
operation.
• Wear substantial footwear and long trousers. Do not
operate the equipment when barefoot or wearing open
sandals.
• Do not wear loose tting clothing that can get caught in
moving parts.
• Always wear eye protection when operating the equipment.
• Stay alert for holes in the terrain and other hidden hazards.
• Watch out for tra󰀩c when crossing or near roadways.
• Before you operate any feature of this machine, observe
your surroundings and look for bystanders.
• Always wash hands after contact with fertilizers and
pesticides.
• Keep all nuts, bolts and screws tight to be sure the
equipment is in safe working condition.
• Always remove material from hopper before attaching
spreader on a vehicle-mounted spreader caddy.
Towing Loads Safely
• Stopping distance increases with speed and weight of
towed load. Travel slowly and allow extra time and distance
to stop.
• Total towed weight must not exceed limits specied in towing
vehicle operator’s manual.
• Excessive towed load can cause loss of traction and loss of
control on slopes. Reduce towed weight when operating on
slopes.
• Never allow children or others in or on towed equipment.
• Use only approved hitches. Tow only with a machine that
has a hitch designed for towing. Do not attach towed
equipment except at the approved hitch point.
• Follow the manufacturer’s recommendations for weight
limits for towed equipment and towing on slopes. Use
counterweights or wheel weights as described in the
machine operator’s manual.
• Do not turn sharply. Use additional caution when turning or
operating under adverse surface conditions. Use care when
reversing.
• Do not shift to neutral and coast downhill.
Read the general safety operating precautions
in your machine operator’s manual for additional
safety information.
Safety

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 4 1019884-B
Hardware Identifier
DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 [phone]
ILLUSTRATIONS ON THIS PAGE ARE TO SCALE FOR FASTER
IDENTIFICATION OF HARDWARE DURING ASSEMBLY.
Drawbar Pin, 1/2" x 2 1/2" (x1) . . . . . . . . . . . . . . . . . . . .
B-3861
Bolt; Carriage, 5/16” -18 x 2” (x2) . . . . . . . . . . . . . . . . . . . . . . . . .
11M1032P
Hairpin Cotter, 1/8” (x1) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A2 B2 C2 D2 H2
Washer
5/8”
(x6)
45M2121P
Cotter Ring
(x1)
1019596
Tube Plug
1.25” (x2)
1020043
Lock Nut
5/16” -18
(x11)
B-4786
Axle Bearing
(x2)
F-283
Axle Spacer
(x2)
E2
G2
J2
L2
M2
F2
Clevis Pin, 3/16" (x1)
1001274
Bolt; Hex Head, 5/16” -18 x 2” (x9) . . . . . . . . . . . . . . . . . . . . . . . .
2M1032P
Rue Ring (x1)
1005414
1”
Hairpin Cotter, 1/8” (x1) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D-146P
R2
Lock Nut
1/4” -20
(x15)
B-4785
NOTE: An extra washer (C2) has been provided /
may be remaining after assembly is complete.
1020012

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 5 1019884-B
Hardware Identifier
DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 [phone]
ILLUSTRATIONS ON THIS PAGE ARE TO SCALE FOR FASTER
IDENTIFICATION OF HARDWARE DURING ASSEMBLY.
Bolt; Hex Head, 1/4” -20 x 1-3/4” (x3) . . . . . . . . . . . . . . . . . . . . . . . . . .
2M0828P
Bolt; Hex Head, 1/4” -20 x 1-1/2” (x1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2M0824P
Bolt; Carriage, 1/4” x 1-1/2” (x1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bolt; Carriage, 1/4” x 1-1/2”
(x1) . . . . . . . . . . . . . . . . . .
Bolt; Hex Head, 1/4” -20 x 2-1/4” (x1) . . . . . . . . . . . . . . . . . . . .
2M0836P
N2 Q2 U2
W2
O2
Handle
Knobs (x2)
1007828
Spinner Clip
(x1)
Felt
Washer
(x2)
Washer
1/4”
(x5)
45M0909P
Nylon Flange
Bushing
(x4)
1001533
P2
S2
V2
X2
Y2
T2
Bolt; Hex Head, 1/4” -20 x 2” (x4) . . . . . . . . . . . . . . . . . . . . . . . . .
2M0832P
Spinner
Clip (x1)
1001683
Bolt; Hex Head, 1/4” -20 x 1” (x3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2M0816P
Linkage Pin (x1) . . . . . . . .
K2
Washer
5/16”
(x2)
45M1111P
A3
Z2
Linkage
Rod (x1) . . . . . . . .
1019875
Agitator (x1) . . . . . . . .
10002231019874

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 6 1019884-B
No. Part # Qty Description
K1019869-10 1Pivot Plate
L1019868-10 1Lever Stop Bracket
M1019870-10 1Gate Lever
N1019872-10 1Linkage Arm
O1019873-10 1Linkage Pivot
P1019901 1Hopper Cover
Q1019900 1Screen
No. Part # Qty Description
A1019891-10 1Painted Frame, 200#
B1019992-2 1Axle Assembly, 200#
C1019863 2Pneumatic Wheel, 15-6-6
D 1019894-10 1 Painted Cross Brace, 200#
E1019896-10 1Tow Bar
FR-892-10 2Clevis
G1020016-10 2Tow Bar Brace
H1000607 1Spinner - Drilled (black)
I1019895-10 1Riser Bar
J1020128 1Hopper, 200lb
└ 1019899 1Tow Spreader Gate Assy
Part Explosion
DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 [phone]
F2
D2
E2
H
B2
A2
C2
C2
C
C
A
L2
K2
J2
H2
B
K2
F
M2
E
B2
A2 C2
J
Q
P
O2
P2

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 7 1019884-B
Part Explosion
DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 [phone]
No. Part # Qty Description
A2 F-283 2Axle Bearing
B2 1020012 2Axle Spacer, 0.625
C2 45M2121P 6Washer; Flat, 5/8
D2 1019596 1Cotter Ring, S/S
E2 1001274 1Clevis Pin, 3/16 x 1-3/4
F2 1005414 1Rue Ring Locking Pin
G2 2M1032P 9Bolt; Hex Head, 5/16 x 2
H2 B-4786 11 Nut; Nylon Lock, 5/16-18
I2 1020043 2Tube Plug, 1.25" 14ga
J2 11M1032P 2Bolt; Carriage, 5/16 x 2
K2 45M1111P 2Washer; Flat, 5/16
L2 B-3861 1Pin; Hitch, 1/2" x 2-1/2"
M2 D-146P 1Cotter; Hairpin, 1/8", #211
N2 1000198 2Felt Washer
No. Part # Qty Description
O2 1001683 1Spinner Clip
P2 2M0832P 4Bolt; Hex Head, 1/4 x 2
Q2 45M0909P 5Washer; SAE Flat, 1/4"
R2 B-4785 15 Nut; Nylon Lock, 1/4-20
S2 2M0828P 3Bolt; Hex Head, 1/4 x 1-3/4
T2 2M0836P 1Bolt; Hex Head, 1/4 x 2-1/4
U2 1001533 4Nylon Flange Bushing
V2 2M0824P 1Bolt; Hex Head, 1/4 x 1-1/2
W2 1007828 2Knob, Handle
X2 2M0816P 3Bolt; Hex Head, 1/4 x 1
Y2 1019874 1Linkage Pin
Z2 1019875 1 Linkage Rod
A3 1000223 1Agitator Wire
Contents of Hardware Pack: 1019885
L
W2
R2
Q2
V2
R2
R2
Y2
R2
Z2
D
A
E
G2
G2
G2
O
G2
H2
G2
R2
R2
R2
K
M
N
G
G
G2
H2
H2
H2
G2
R2
U2
X2
H2
H2
S2
S2
U2
X2
U2
R2
X2
2
2

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 8 1019884-B
No. Part # Qty Description
B1019992-2 TRANSMISSION
B3 1000053 1Roll Pin, 1/8 x 3/4"
B4 1001299 2Gearbox Bushing, 5/8"
B5 1001301 2Bushing; Spinner Shaft, 3/8"
B6 1001303 8Bolt; Flange Head, 10-24 x 5/8" SS
B7 1001304 1Dowel Pin; SS, 3/16 x 1"
B8 1001516 1Bevel; Gear
B9 1001518 1Pinion; Gear
B10 1005336 1Gear Box Cover; Front
B11 1005337 1Gear Box Cover; Rear
B12 1005368 1Grease Zerk Drive IN, 1/4"
B13 1005389 1Nylon Spacer, Pin Retain
B14 1019860 1Fan Shaft, Tow Spreader
B15 B-3385 8Nut, Nylon Lock, #10-24
N2 1000198 1Felt Washer
No. Part # Qty Description
1019899 GATE ASSEMBLY
N2 1000198 1Felt Washer
R3 1000203 1Hopper Bottom Bearing
R4 1000210 1Rate Gate
R5 1000211 1Dial Mount
R6 1000213 1Dial, Plastic
R7 1000215 1Pine Tree Clip
R8 1001521 2Guide, Rate Gate/Accuway
R9 1001523 1Accuway Diffuser
R10 1001526 1Accuway Adjustment Screw
R11 1019761 1Hopper Bottom
R12 1019861 1Accuway Adjustment Nut
R13 1019876 1Rate Gate Link
R14 45M0909P 10 Washer, SAE Flat, 1/4"
R15 2M0812P 5Bolt, Hex Head, 1/4 x 3/4
R16 B-4785 5Nut, Nylon Lock 1/4-20
Part Explosion
DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 [phone]
N2
R11
R9
R3
R10
R13
R4
R8
R5
R6
R7
R8
R12
R15
R14 x5
R14
x5
x5
R16 x5
B14
B12
B13
B3
B5
N2
B5
B9
B4
B4 B7
B8
B6 x8
B15 x8
B10
B11

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 9 1019884-B
Assembly
ASSEMBLY TIP
1-A. Installing the Axle
Alignment is crucial. The frame (A) and transmis-
sion (B) must be aligned as illustrated here.
It is also important that the axle (#) is facing the cor-
rect direction. (Note the arrows pointing out locations
of holes on the axle).
Slide axle (#) through the square holes at the base of
the frame (A).
1-B. Installing the Axle
Add the bushings (A2) by sliding over the axle ends
(#) and fitting in the square openings at the base of
the frame (A).
2. Installing the Drive Wheel
Note the location of the remaining axle holes. The
wheel will need to be installed on the side marked
“1” below.
On the (1) end of the Axle:
Add a 5/8” washer (C2), axle spacer (B2), a
second 5/8” washer (C2), then the wheel (C).
2
1
C2
B2
C
bag #2
Step 2
bag #1
Step 1
bag #3
Step 3 #
A2
A2
#A
A
The hardware pack for this assembly is
organized in bags that are numbered to match
the steps of this manual.
A
B
#
Secure the wheel
in place with the
3/16” clevis pin (E2)
and cotter ring (D2),
as illustrated.
D2
E2

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 10 1019884-B
Assembly
3. Install the Second Wheel
On the opposite end of the axle: Add a washer (C2),
spacer (B2), another washer (C2), then the wheel (C).
After adding the wheel, add 1 to 2 washers (C2) as
needed, then secure with the rue ring (F2).
NOTE: An extra washer will be provided.
5 . Attaching the Tow Bar
NOTE: For this step, you will need to measure the
height of your mower hitch to the ground.
-For Hitch Heights 9” or Below:
C2
B2
C
C2
F2
4. Adding the Cross Brace
Align the cross brace (D) to the frame (A) as illus-
trated below. On each end, insert a 5/16” x 2” bolt
(G2) and secure beneath the frame with a 5/16”
locknut (H2).
NOTE: Wheels not illustrated on
this step for clarity / proper alignment.
H2
D
H2
G2
G2
Align the tow bar (E) below the
cross brace (D) as illustrated above.
LOOSELY bolt the towbar (E) to the cross
brace using two 5/16” x 2” bolts (G2), securing
from below with two 5/16” lock nuts (H2). Insert
the 1.25” tub plug (
II
2) in the end of the towbar.
NOTE: These bolts will be tightened on step 8.
G2
H2
E
II2
D
Align the tow bar (E) below the
cross brace (D) as illustrated above.
Loosely bolt the towbar (E) to the cross brace
using two 5/16” x 2” bolts (G2), securing from
below with two 5/16 lock nuts (H2). Insert the
1.25” tub plug (
II
2) in the end of the towbar.
NOTE: These bolts will be tightened on step 8.
G2
H2
E
II2
D
- For Hitch Heights Over 9” O󰀨 the Ground:

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 11 1019884-B
Assembly
6. Adding Clevis Plates
Align the clevis plates (F) with the towbar (E) as illus-
trated. Run two 5/16” x 2” carriage bolts (J2) through
these parts and secure from below with two 5/16”
washers (K2) and two 5/16” lock nuts (H2).
Add the drawbar pin (L2) and secure from below with
a hairpin cotter (M2).
8. Attach Support Brackets
Align the assembly from Step 7 as illustrated. Next,
LOOSELY bolt the frame support brackets to the
tow bar (E) and frame (A) using:
- (x3) 5/16” x 2” Bolts (G2)
- (x3) 5/16” Lock Nuts (H2)
After ensuring the towbar is squared up to the
frame, tighten all bolts from steps 5 and 7.
9. Adding Fan
Slide the felt washer (N2) and fan (H) on the
fan shaft. Look for the hole at the middle of the fan
shaft. This is where the fan will rest (see illustra-
tion) as the spinner clip (O2) slides through the
base of the fan (H).
NOTE: Secure by tilting the clip down and apply
slight pressure to snap in place around the fan shaft.
L2
J2
M2
H2
K2
F
F
7. Frame Support Brackets
Insert the tube plug (
II
2) in the long end of the riser
bar (
II
). Align the frame support brackets (G) with the
riser bar (
II
) as illustrated. LOOSELY bolt these
parts using:
- (x2) 5/16” x 2” Bolts (G2)
- (x2) 5/16” Lock Nuts (H2)
NOTE: This hardware will be tightened on step 8.
G
G
II2
II
H2
G2
G2
H2
H2 G2
H2
G2
E
A
A
H
O2
O2
H
N2

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 12 1019884-B
12. Lever Stop Bracket
As illustrated here, align the lever stop
bracket (L) holes with the openings at the
top of the riser bar (
II
).
For now, secure in place only through the
LOWER of the two bolt holes using:
- (x1) 1/4” x 1-3/4” Bolt (S2)
- (x1) 1/4” Lock Nut (R2)
13-A. Adding the Gate Lever
Assemble the gate lever handle (M) as illustrated
using the following parts:
- (x1) 1/4” x 1-1/2” Hex Head Bolt (V2)
- (x1) 1/4” Flat Washer, SAE (Q2)
- (x2) Handle Knobs (W2)
- (x1) 1/4” Lock Nylon (R2)
11. Adding Pivot Plate
Align the pivot plate (K) to the riser bar (
II
) as
illustrated. Secure with:
- (x2) 1/4” x 1-3/4” Bolts (S2)
- (x2) 1/4” Lock Nuts (R2)
10. Installing Hopper
Place the hopper assembly (J) on top of the frame
(A). Slide the fan shaft (#) through the bushing in the
hopper bottom plate. Secure the hopper to the frame
by using the following as illustrated above:
- (x4) 1/4” x 2” Bolts (P2)
- (x4) 1/4” Washers (Q2)
- (x4) 1/4” Lock Nuts (R2)
S2
R2
L
II
W2
R2 W2
Q2 V2
M
Assembly
P2
J
Q2
R2
#P2
Q2
R2
A
Q2
Q2
R2
R2 S2
K
S2
II

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 13 1019884-B
Assembly
13-B. Adding the Gate Lever
Align the gate lever (M) assembled in step 13-A
with the stop bracket (L). Bolt GENTLY using
the following parts:
- (x1) 1/4” x 2-1/4” Hex Head Bolt (T2)
- (x1) Nylon Flange Bushing (U2)
- (x1) 1/4” Lock Nut (R2)
NOTE: Bolt together allowing the lever to pivot
but can’t move freely (snug but not tight).
15. Linkage Pivot
Attach linkage pivot (O) with hardware in the
following order: (NOTE: Bolt together snug but
not tight).
16. Linkage Pin
Attach the linkage pin to the base of the linkage
pivot (O) that was added on step 15.
- (x1) Linkage pin (Y2)
- (x1) 1/4” Lock Nut (R2)
NOTE: Bolt together snug but not tight.
U2
R2
L
M
14. Linkage Arm
Place a Nylon Flange Bushing (U2) between
the linkage arm (N) and gate lever (M). Bolt
together using:
- (x1) 1/4” x 1” Bolt (X2)
- (x1) 1/4” Lock Nut (R2)
NOTE: Bolt together snug but not tight.
U2
R2
X2
N
M
Bolt 2:
- 1/4” x 1” Bolt (X2)
- Linkage Pivot (O)
- Flange Bushing (U2)
- Pivot Plate (K)
- 1/4” Lock Nut (R2)
Bolt 1:
- 1/4” x 1” Bolt (X2)
- Pivot Plate (K)
- Linkage Pivot (O)
- Flange Bushing (U2)
- Linkage Arm (N)
- 1/4” Lock Nut (R2)
Y2
O
R2
U2
U2
X2
KR2
R2
O
1
N
X2
2

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 14 1019884-B
Assembly
18. Agitator Pin
Slide the felt washer (N2) onto the fan shaft
and insert the agitator pin (A3).
19. Screen and Cover
Place the screen (Q) down inside the hopper.
Attach the hopper cover (P) by hooking it around
the rim of the hopper.
R2 R2
Open Closed
17-B. Linkage Rod
Adjust the position of the two lock nuts (R2) that
were added on step 17-A such that the gate is
in the no more that 1/16” past the fully closed
position.
17-A. Linkage Rod
a. On the linkage rod (Z2): Add a 1/4” lock nut
(R2), stop at about 3/4 of the thread length.
b. Insert the bent portion of the linkage rod (Z2)
through the hole in the gate link (#), as illus-
trated.
c. Insert the threaded portion of the linkage rod
(Z2) through the hole in the linkage pin (Y2)
and secure with the second lock nut (R2).
Z2
R2
Y2
cb
#
Z2
a
Z2
R2
A3
N2
Q
P
Assembly is complete.

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 15 1019884-B
Use and Care
TIP: Read this entire Use and Care
Section and become familiar with the
operation of the spreader BEFORE
you put material in the hopper.
SPY200T-1P
SPECIFICATIONS
200 lb Spreader (SPY200T-1P)
Capacity
Spreader Weight ..........49 lbs (20.2 kg)
Hopper Capacity .........200 lbs (90.7 kg)
Maximum Combined
Weight ................ 249 lbs (112.9 kg)
Tires
Pneumatic ........15 x 6 NHS 2-Ply Rating
Max Inflation Pressure* .... 30 psi (207 kPa)
*Tire pressure may be reduced to increase
wheel traction or to reduce shock, although it
should not be reduced to below 70% of the
maximum rated pressure.
Hopper
Volume ...................3.5 ft3(0.1 m3)
Material ........ High Density Polyethylene
1. Inate tires to 20 PSI-30 PSI (1.4 BAR-2.1 BAR)
(138kPa-207kPa) maximum.
2. Check bushings and bearing surfaces for proper
lubrication (See service section).
3. Be sure controls operate smoothly and spreader
wheels turn freely.
4. Before filling hopper, practice spreading.
Become accustomed to operating the on/off
control lever while spreader is in motion.
BEFORE OPERATING
THE SPREADER
ON / OFF CONTROL LEVER
1. Use On / O󰀨 control lever (M) to open and close
hopper gate while spreader is in motion. This starts
and stops material ow.
2. To OPEN the ow gate:
Move control lever (M) towards spreader.
3. To CLOSE ow gate.
Move control lever away from spreader.
CLOSE
Flow Gate
OPEN
Flow Gate
M

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 16 1019884-B
Use and Care
INSTALLING
1. Park machine safely.
(See Parking Safely in the SAFETY section.)
2. Remove spring locking pin (M2) and hitch pin (L) from
clevis plates (F) of spreader.
3. Pull spreader forward and position hitch clevis (#)
to straddle machine rear hitch plate or drawbar
(shown below).
Align all hitch pin holes, then install hitch pin (L) down
through hitch clevis and machine hitch, securing with
spring locking pin (M2).
L
F
M2
L
M2
#
REMOVING
1. Park machine safely. See “Parking Safely” in the
Safety section.
2. Remove all materials from the hopper before
removing spreader from machine.
CAUTION: Avoid injury! Keep hands,
feet and other body parts away from under
the drawbar.
3. Remove 1/8 in. spring locking pin (M2) from hitch pin.
4. Hold spreader tow tube to remove pressure from
hitch pin, then remove hitch pin (L) from hitch clevis
and rear hitch plate or drawbar on machine.
5. Pull or push spreader backward to disengage the hitch
clevis from machine hitch, install hitch pin in hitch clevis
for storage and secure with 1/8 in. spring locking pin.
L
M2

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 17 1019884-B
DETERMINING
APPLICATION FLOW SETTING
1. Check material manufacturer’s container for
recommended application ow and setting for your
spreader. If no specic recommendation is found,
use setting for similar type spreaders sold by other
companies.
2. Use application ow setting charts when spreading
grass seed or when material size and desired
coverage is known, but no setting is recommended
by the material manufacturer.
Flow control dial (#) rotates
to adjust the opening size in
hopper bottom.
Dial has nine numbers with
ten positions between each
number for fine adjustment.
Turn dial to adjust for
desired application ow.
Small numbers provide the
smallest opening.
#
Use and Care
OPE R ATIONUSING THE FLOW CONTROL DIAL
Understanding Full and Half Flow Settings
NOTE: Half Flow is a proportional reduction of Full Flow
not one-half of Full Flow. For half ow application, set
ow control dial according to “Half Flow” value shown in
appropriate table. Do not set ow dial at half the
recommended full ow value.
^
“Full Flow” setting is
used when single pass
(once over) operation
is planned.
^
“Half Flow” setting
is used for two pass
(twice over) operation and
improved coverage.
TWICE OVER - 1/2 Flow
Full Flow Once Over
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
Half Flow Twice Over
1.50
2.00
2.25
3.00
3.50
3.90
4.20
4.70
5.00
5.30
5.70
5.80
6.00
6.50
7.10

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 18 1019884-B
Use and Care
FILLING THE SPREADER
CLOSE
FLOW
GATE
M
1. Attach hitch to tractor/mower with hitch pin. Fasten
with spring pin.
3. To avoid material loss, ll spreader on a sidewalk,
driveway, plastic sheet or cardboard.
CAUTION: Avoid injury!
Chemicals can be dangerous.
Avoid injury to operator or bystanders:
• Read chemical container label for
handling instructions. A Material Safety
Data Sheet (MSDS) should be supplied by
the chemical dealer and provides proper
safety information.
• Wear proper clothing and safety
equipment while handling or applying
chemicals.
• Prohibit all smoking, drinking, and
eating around chemicals.
2. Use the On / O󰀨
control lever (M) to
close product gate at
hopper bottom.
NOTE:
Fill spreader on
a at, level surface.
Spreader may be
unstable when fully
loaded on an incline.
Fill spreader according
to manufacturer’s
instructions only.
Overlling may cause
instability or damage to
the spreader.
ADJUSTING SPREAD PATTERN
Adjusting knob (&) moves di󰀨user plate (#) forward and
backward to center spread pattern and reduce side-throw
(or skewing).
NOTE: The spread pattern can be affected by many
variables such as humidity, temperature, wind, spreader
condition, speed of travel, material size, & weight. Proper
adjustment will minimize spread pattern skewing and
uneven coverage.
MANY VARIABLES CAN AFFECT
THE SPREADING PATTERN:
• Product size, weight, shape, surface nish
• Spreading rate (light, medium, heavy)
• Weather conditions
• Operating speed
• Tilting of spreader
• Condition of spreader and spreader spinner
Because of these variables, the di󰀨user plate must be set
for each type of application.
&
#

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 19 1019884-B
NOTE: This adjustment is very sensitive. Turning
diuser knob (&) just a little will result in drastic change
to the spread pattern.
1. On a at, bare surface such as a paved driveway,
operate the spreader and observe the spreading
pattern. If spreading pattern is centered around
spreader, do not adjust di󰀨user.
2. If spreading pattern is not centered around spreader,
adjust as follows and retest:
NOTE: Adjusting the spread pattern will not change the
width of spread.
Never adjust so the di󰀨user plate splits the material ow
to both center and outside of spreader. (Knob centered
between full clockwise and full counterclockwise.)
If spreading is long to the left of center, turn di󰀨user knob
counterclockwise all the way; then turn knob clockwise
until edge of di󰀨user plate (#) directs material slightly to
outside of spreader as it falls on the spinner and test
pattern is centered.
If spreading is long to the right of center, turn di󰀨use
knob clockwise all the way; then turn knob
counterclockwise until edge of plate directs material
slightly to center of spreader as it falls on the spinner.
Continue to turn knob in small increments until test
pattern is centered.
#
OPERATING TIPS
FOR UNIFORM SPREADING
USE THE FOLLOWING PROCEDURE
WHILE SETTING THE SPREAD PATTERN
Use and Care
SPREADING ICE MELT
NOTE: Use higher flow settings (5 - 9) for wider
product opening when spreading ice melt.
1. Install agitator to break up clumps
2. Starting with ow setting at 5, make a trial pass over
the spreading area and check coverage. Adjust ow
setting up to improve coverage or down to reduce
coverage.
IMPORTANT: Avoid damage! Clean
and lubricate axle bearings after spreading
ice melt to avoid damage to bearings.
3. After spreading, be sure to thoroughly rinse the
ice melt dust from all surfaces, as ice melt is highly
corrosive.
1. Keep spinner blades clean. A buildup of material on
the spinner blades can cause uneven spreading.
2. Use on/o󰀨 control to open and close product gate
only when spreader is in motion. Close product gate
as you enter turn-around areas.
3. Maintain even, normal travel speed of 3 mph /
264 fpm (4.8 kph/80 meters per min). Faster travel
throws material further for a wide spread pattern and
lighter coverage. Slower travel spreads a narrow
pattern with heavier coverage.
4. Travel in straight rows. Keep your eyes on the far
end of the area to keep spreader in alignment with
previous pass.
NOTE: Spreader tapers the spreading edge, which
allows you to operate at approximately spreading widths.
Extra material can be spread under trees and other high
feeding areas without showing the spreading edges.

©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 20 1019884-B
Use and Care
SPREADING THE MATERIAL
Two methods of spreading the material, Dual Pass and Single Pass are described below:
Single Pass Coverage
NOTE: This is also known as the “Full Flow” method, which
consists of making a single pass over area with ow control
dial set at full ow setting.
1. Set ow control dial to “Full Flow” setting
(See ow setting tables earlier in this manual.).
2. Spread header strips (B) at each end of area. This allows
a turn-around area to align spreader for next pass.
3. Make passes between header strips at each end of area.
(Refer to “Keys to Uniform Spreading” covered previously
in manual).
IMPORTANT: Avoid damage!
Never leave fertilizer in the hopper.
Fertilizer draws moisture, forms clumps,
causes unnecessary rusting and
deterioration of spreader, and may jam
controls and other moving parts. Salt
residue is especially corrosive. Clean and
oil spreader immediately after each use.
B
B
2. Spread header strips (A) at each end of area. This allows
a turn-around area to align spreader for next pass.
3. Make passes between header strips at each end of area.
(Refer to “Keys to Uniform Spreading” covered previously
in manual).
4. Repeat steps two and three using passes in cross
direction to those used previously.
1. Set ow control dial (#) to
“Half Flow” setting described in
the “Understanding Full and Half
Flow” section on page 17.
NOTE: “Half Flow” is a prop-
ortional reduction of “Full Flow”,
not one-half of “Full Flow.”
See Flow Setting Tables.
Dual Pass Coverage (Preferred Method)
NOTE: This method is also known as the “Half Flow”
method, which consists of making two passes in cross
directions with ow control dial set at a half ow setting. This
method provides the most complete coverage while correcting
for operation or ow errors made with a single pass.
A
A
#