Stagg Ecopar 630 31 User manual

USER MANUAL
Ecopar 630 31
SLI-Ecopar63031
Please read the instructions carefully before use

!
SAFETY INSTRUCTIONS
Please read the instructions carefully as they include important
information about the installation, operation and maintenance.
• Please keep this user’s guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
• All fixtures leave the manufacturer intact. Please note that any damages incurred
by the user is not covered by the guarantee.
• Unpack and check carefully that there is no transportation damage before using the
unit.
• The unit is for indoor use only. Use only in a dry location.
• Use a safety bond when attaching the fixture to a lighting rig. Handle by the
hanging bracket when fixing.
• The unit must be installed in a location with adequate ventilation at least 50 cm
from adjacent surfaces.
• Make sure that no ventilation slot is blocked, otherwise the unit will overheat.
• Before operating, ensure that the voltage and frequency of the power supply match
the power requirements of the unit.
• Make sure all equipment is properly earthed.
• Do not operate the unit if the ambient temperature is higher than 40°C.
• Do not hardwire to any mains dimmer.
• On the first start, there may be some normal operational start-up smell.
• Make sure that there is no flammable material close to the unit while operating, as
it is a fire hazard.
• Examine power wires carefully and replace immediately if there is any damage.
• Never run on for a long time lest shortening lifespan. Avoid any inflammable liquids,
water or metal objects entering the unit. In case it happens, cut off the mains power
immediately.

• Do not operate in a dirty or dusty environment. Clean fixtures regularly.
• Do not allow children unsupervised to operate the fixture.
• Do not touch any wire during operation as there might be a hazard of electric
shock.
• Avoid placing power wires next to other cables.
• Disconnect the mains power before replacing or servicing the fuses.
• Replace fuse only with the same type.
• In the event of a serious operating problem, stop using the unit immediately.
• Never turn on and off the unit time after time.
• The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
• Do not open the unit as there is no user serviceable part inside.
• Never try to repair the unit by yourself. Repairs carried out by unskilled people can
lead to damage or malfunction. Please contact the nearest authorized technical
assistance centre.
• Disconnect the mains power if the fixture is not used for a long time.
• Use the original packaging to transport regarding any warranty issue.
• Do not look directly at the LED light beam while the fixture is on.
• Do not connect more than 7 units to the same power source.

INSTALLATION
The unit should be mounted via its screw holes on the bracket. Always ensure that the
unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that
the structureto which you are attachingthe unit is secure and able to support 10 times
the unit’s weight. Also, always use a safety cable that can hold 12 times the unit’s
weight when installing the fixture.
The equipment must be fixed in an appropriate place by professionals. Keep it out of
the reach of unqualified people.
TECHNICAL SPECIFICATIONS
Flat ECOPAR 6 spotlight with 6 x 30-watt RGB (3 in 1) LED
- LED: 6 x 30 watts
- Protocol: DMX-512, 8 channels
- Functions: Dimmer (0-100 %), strobe (0-20 Hz), auto, sound control, master/slave.
- Display: 4-digit
- Housing: ABS
- Fixation: 2 brackets (to hang or lay the spotlight)
- Input and output: 3-pin DMX and IEC
- Cooling: Low-noise fan
- Use: Indoor
- Power consumption: 200 watts
- Dimensions: 215x210x100 cm (8,5 x 8,3x 3,9")
- Weight: 1.5 kg (3,3 lb)

SETTING UP THE DEVICE

DMX Mode
With the menu button, select the DMX mode (dxxx) and press the enter key to
confirm. Then use the up and down buttons to choose the desired DMX channel (1 –
512) and press the enter key to confirm.
Press the menu button to return to the main menu.
Channel
Range
Function
CH1
0-255
Dimmer
CH2
1-255
Strobe
CH3
1-255
Macro function
CH4
0-255
Macro speed adjust
CH5
0-255
Red
CH6
0-255
Green
CH7
0-255
Blue
Automatic mode
With the menu button, select the automatic mode (Auxx) and press the enter key to
confirm. Then use the up and down buttons to choose between
- Au01 to Au10 and press enter. In this mode, the fixture will play an automatic
sequence.
- So01 and So02 and press enter. In this mode, the fixture will react to the sound
thanks to the integrated microphone.

Strobe Mode
With the menu button, select the Strobe mode (Stxx) and press the enter key to
confirm. Then use the up and down buttons to select the desired mode.
-St00: Auto Master without strobe
-St01 to St16: Strobe Speed from slow to fast
In this mode, the fixture will play flashes at different speeds.
Sound Mode
With the menu button, select the Sound mode (Snxx) and press the enter key to
confirm. Then use the up and down buttons to select the desired preset from Sn01 to
Sn16.
Speed control
With the menu button, select the Speed control mode (Spxx) and press the enter key
to confirm. Then use the up and down buttons to select the desired preset from Sn00
to Sn16.
Thanks to this function, you can adjust the speed of the automatic mode. From slow
to fast.
Colour mode:
With the menu button, select the Red (rxxx) Green (Gxxx) or blue (bxxx) and press
the enter key to confirm. Then use the up and down buttons to increase or decrease
the colour amount (from 001 to 512).
Thanks to this colour mixing mode, you can virtually choose all the desired fixed
colours.

DMX512 CONNECTIONS
The DMX512 is widely used in intelligent lighting control, with a maximum of 512
channels.
Warning
To avoid signal transmission problems and interferences when using fixtures in
chain, use a Stagg N-series professional 3-pin DMX terminator (resistance: 120
ohms; pin2: DMX-; pin3:DMX+).
FIXTURE CLEANING
An internal cleaning must be carried out periodically to optimize the light output. The
cleaning frequency depends on the environment in which the fixture operates: A
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt
on the fixture’s optics. Clean the fixture with a soft cloth and normal glass cleaning
fluid. Always dry the parts carefully. Clean the external optics at least every 20 days.

For more info and the latest product updates:
staggmusic.com
EMD Music S.A.
Boulevard Général Wahis 16A
1030 Brussels
Belgium
05/2018