Stagg Truss34 User manual

USER MANUAL
Truss34
SLI-TRUSS34
Please read the instructions carefully before use

!
SAFETY INSTRUCTIONS
Please read the instructions carefully as they include important
information about the installation, operation and maintenance.
• Please keep this user’s guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
• All fixtures leave the manufacturer intact. Please note that any damages incurred
by the user is not covered by the guarantee.
• Unpack and check carefully that there is no transportation damage before using the
unit.
• The unit is for indoor use only. Use only in a dry location.
• Use a safety bond when attaching the fixture to a lighting rig.
• The unit must be installed in a location with adequate ventilation at least 50 cm
from adjacent surfaces.
• Make sure that no ventilation slot is blocked, otherwise the unit will overheat.
• Before operating, ensure that the voltage and frequency of the power supply match
the power requirements of the unit.
• Make sure all equipment is properly earthed.
• Do not operate the unit if the ambient temperature is higher than 40°C.
• Do not hardwire to any mains dimmer.
• On the first start, there may be some normal operational start-up smell.
• Make sure that there is no flammable material close to the unit while operating, as
it is a fire hazard.
• Examine power wires carefully and replace immediately if there is any damage.
• Never run on for a long time lest shortening lifespan. Avoid any inflammable liquids,
water or metal objects entering the unit. In case it happens, cut off the mains power
immediately.

• Do not operate in a dirty or dusty environment. Clean fixtures regularly.
• Do not allow children unsupervised to operate the fixture.
• Do not touch any wire during operation as there might be a hazard of electric
shock.
• Avoid placing power wires next to other cables.
• Disconnect the mains power before replacing or servicing the fuses.
• Replace fuse only with the same type.
• In the event of a serious operating problem, stop using the unit immediately.
• Never turn on and off the unit time after time.
• The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
• Do not open the unit as there is no user serviceable part inside.
• Never try to repair the unit by yourself. Repairs carried out by unskilled people can
lead to damage or malfunction. Please contact the nearest authorized technical
assistance centre.
• Disconnect the mains power if the fixture is not used for a long time.
• Use the original packaging to transport regarding any warranty issue.
• Do not look directly at the LED light beam while the fixture is on.
• Do not connect more than 7 units to the same power source.

INSTALLATION
The unit should be mounted via its screw holes. Always ensure that the unit is firmly
fixed to avoid vibration and slipping while operating. Always ensure that the structure
to which you are attaching the unit is secure and able to support 10 times the unit’s
weight. Also, always use a safety cable that can hold 12 times the unit’s weight when
installing the fixture.
The equipment must be fixed in an appropriate place by professionals. Keep it out of
the reach of unqualified people.
TECHNICAL SPECIFICATIONS
Truss lighting with 3 x 4-watts (4 in 1) LED
- LED: 3 x 4 watts
- Illuminance: 1866 lux at 2 metres (96,6')
- Beam angle: 30°
- Protocol: DMX-512 (4, 6 or 8 channels)
- Functions: Dimmer (0-100 %), strobe (0-20 Hz), auto, sound control,
master/slave, remote control
- Remote control included
- Display: 4-digit
- Housing: Metal
- Fixing: 3 x M10 and 1 x M12 threaded holes
- Input and output: 3-pin DMX and IEC in and out
- Cooling: Low-noise fan
- Use: Indoor
- Power consumption: 80 watts
- Dimensions: 10.8 x 10.8 x 10.4 cm (4.3 x 4.3 x 4.1")
- Weight: 0.6 kg (1.3 lb)

SETTING UP THE DEVICE

DMX Mode
With the menu button, select the DMX mode (dxxx) and press the enter key to
confirm. Then use the up and down buttons to choose the desired DMX channel (1 –
512) and press the enter key to confirm. Then use the up and down buttons to select
the desired channel mode (4, 6 or 8 channels) then press enter. Press the menu
button to return to the main menu.
DMX Channel Modes, Assignments, and Values :
4 Channels
Channel
Function
Value
CH1
RED
0~255
CH2
GREEN
0~255
CH3
BLUE
0~255
CH3
WHITE
0~255
6 Channels
Channel
Function
Value
CH1
DIMMER
0~255
CH2
STROBE
0~255
CH3
RED
0~255
CH4
GREEN
0~255
CH5
BLUE
0~255
CH6
WHITE
0~255

8 Channels
Channel
Function
Value
Note
CH1
Dimmer
0-255
CH2
Strobe
0-255
Slow -> Fast
CH3
Manual
0
CH4 -8 are enabled
Program1
001-035
Program2
036-071
Program3
072-107
Program4
108-143
Program5
144-179
Program6
180-215
Program7
216-251
Sound
252-255
CH4
Speed (If CH3≠0)
0-255
Colour 1
0~14
Colour 2
15~29
Colour 3
30~44
Colour 4
45~59
Colour 5
60~74
Colour 6
75~89
Colour 7
90~104
Colour 8
105~119
Colour 9
120~134
Colour 10
135~149
Colour 11
150~164
Colour 12
165~179
Colour 13
180~194
Colour 14
195~209
Colour 15
210~224
Colour 16
225~239
Colour 17
240~254
Colour 18
255
CH5
RED
0-255
CH6
GREEN
0-255
CH7
BLUE
0-255
CH8
WHITE
0-255

Sound Mode
With the menu button, select the Sound mode (Soud) and press the enter key to
confirm. Then use the up and down buttons to select the desired sensibility of the
microphone from Sen0 to Sen9.
Show Mode
With the menu button, select the Show mode (Shou) and press the enter key to
confirm. Then use the up and down buttons to select the desired show from Sh01 to
Sh06 and press the enter key to confirm. You can now change the speed of the
show from SP01 to SP99. Press enter to confirm.
The next menu allows you to add a strobe effect to the show. Use the up and down
buttons to change the strobe speed from St00 to St99.
Sh01
RGBW Single colour gradual change
Sh02
Multicolour gradual change
Sh03
Effect 1
Sh04
Effect 2
Sh05
RGBW Single colour jump change
Sh06
Multicolour jump change

Automatic mode
With the menu button, select the automatic mode (Auto) and press the enter key to
confirm. In this mode, the fixture will play a variety of in-built effects at various
speeds.
Set Menu
With the menu button, select the “Set” menu and press the enter key to confirm.
Then use the enter key ton enter the “remo” menu. You can now use up and down
buttons to activate (on) or deactivate (off) the infra-red system used for the remote
control.
Colour Mode
With the menu button, select the Colour mode (CoLr) and press the enter key to
confirm. Then use the up and down buttons to select the desired colour. Red (rxxx),
Green (gxxx), blue (bxxx), white (Uxxx) and Yellow (Yxxx) and press the enter key to
confirm. Then use the up and down buttons to increase or decrease the colour
amount (from 001 to 255). Press enter to confirm.
Thanks to this colour mixing mode, you can virtually choose all the desired fixed
colours.
You have now access to the pre-programmed colours menu (CCxx). Press enter and
use the up and down button to select it. Press enter to confirm.
The last menu of the colour mode is the strobe function (STxx). Press enter and use
the up and down button to select the desired strobe speed from St00 to St99.
Slave mode
With the menu button, select the slave mode (SLAv) and press the enter key to
confirm. In this mode, the fixture will automatically follow the other BAT34’s present
in the same daisy chain (See “Connections” section). At least one of the BAT32 in
the chain needs to be in another mode.

DMX512 CONNECTIONS
The DMX512 is widely used in intelligent lighting control, with a maximum of 512
channels.
Warning
To avoid signal transmission problems and interferences when using fixtures in
chain, use a Stagg N-series professional 3-pin DMX terminator (resistance: 120
ohms; pin2: DMX-; pin3:DMX+).
FIXTURE CLEANING
An internal cleaning must be carried out periodically to optimize the light output. The
cleaning frequency depends on the environment in which the fixture operates: A
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt
on the fixture’s optics. Clean the fixture with a soft cloth and normal glass cleaning
fluid. Always dry the parts carefully. Clean the external optics at least every 20 days.

For more info and the latest product updates:
staggmusic.com
EMD Music S.A.
Boulevard Général Wahis 16A
1030 Brussels
Belgium
05/2018