LIVARNO LUX 91133 User manual

IAN 91133
HALOGEN RECESSED SPOTLIGHTS
HALOGEN-EINBAULEUCHTEN-SET
Bedienungs- und Sicherheitshinweise
HALOGEN RECESSED SPOTLIGHTS
Operation and Safety Notes

GB/IE Operation and Safety Notes Page 4
DE/AT/CH Bedienungs- und Sicherheitshinweise Seite 8

3
A
C
E
G
B
F
H
1 2 3 4
1
41 D5
10
7
6
9
4
2 4
8
9
44
4 4 approx.
10cm
approx.
10cm
approx. 10cm

4 GB/IE
Halogen recessed spotlights
Intended use
This light set is only suitable for indoor use, in dry
and enclosed rooms. This product is intended
for private household use only.
Parts description
1Lamp housing
2Bulb
3Spring ring
4Retaining spring
5Cover
6Cable holder
7Terminal block
8Fitting (socket)
9Mains socket
10 Tube
Technical Data
Operating voltage: 230V∼, 50Hz
Bulb: 230V, GU10, 40 W
Power consumption: 1 x 40W
Dimensions of each light: ø 85mm
Installation opening: ø 68mm
Protection category:
Model-No.: Z31669A (shiny),
Z31669B (matt)
Scope of delivery
6 Recessed spot lights with pre-installed bulbs
6 Mains connectors
12 Retaining springs
12 Tubes
1 Operating instructions
General safety
instructions
PLEASE READ THE INSTRUC-
TIONS FOR USE PRIOR TO USE!
PLEASE KEEP THE INSTRUC-
TIONS FOR USE IN A SAFE
PLACE!
Check the product for damage
before use. Never use a damaged
product.
DANGER TO LIFE
AND RISK OF ACCIDENTS
FOR INFANTS AND CHIL-
DREN! This appliance can be
used by children aged from
8 years and above and per-
sons with reduced physical,
sensory or mental capabilities
or lack of experience and
knowledge if they have been
given supervision or instruction
concerning use of the appli-
ance in a safe way and under-
stand the hazards involved.
Children shall not play with
the appliance. Cleaning and
user maintenance shall not be
made by children without
supervision.

5GB/IE
Avoid the danger of
death from electric
shock!
Ensure that a qualified electrician,
or a person trained to carry out
electrical installations, performs
the electrical installation.
Always check the light, power
supply, and mains cable for
damage before plugging it in.
Never use the light if it shows
any signs of damage.
Prior to installation, remove the
fuse or switch off the circuit
breaker (0 setting) in the fuse
box.
Before assembly, ensure that
the available mains voltage
corresponds to the operating
voltage necessary for the light
(230V∼).
Ensure that the light does not
come into contact with water
or other liquids under any
circumstances.
Do not install the light on damp
or conductive surfaces.
Prevent fire and
injury hazards
RISK OF INJURY! Check
each bulb and lamp glass for
damage immediately after un-
packing. Do not fit the light if
the bulbs and/or lampshades
are faulty.
RISK OF BURNS! Ensure
that the light has been switched
off and has cooled before
touching it, to avoid burn inju-
ries. Lamps develop a lot of
heat in the area of the lamp
head.
0.5m FIRE HAZARD! Fit
the light so that it is at
least 0.5m away from the
material to be illuminated.
CAUTION! RISK
OF FIRE! Under no
circumstances should you cover
the halogen recessed lights
with heat insulating material
or similar.
Make sure you have adequate
ventilation. The maximum tem-
perature of 90 °C in the area
of fitting may not be exceeded.
Only use the recessed light set
with the accessories that were
delivered with it! Do not con-
nect recessed light sets in a row!
Do not use bulbs with
cool beam reflectors.