Stamina Aero Pilates Performer 271 User manual

When calling for parts or
service, please specify
the following number :
Model#: 55-4271
CAUTION:
Weight on this product should not exceed 300 lbs.
Owner's
Manual
This Product is Produced Exclusively by
2040 N. Alliance, Springeld, MO 65803
Customer Service
1 [phone]
www.staminaproducts.com
Product May Vary Slightly From Pictured.
STAMINA PRODUCTS
MADE IN CHINA
© 2010 Stamina Products, Inc.
2010, 12
Patent Nos. 7,179,207,
7,771,328, D382,319,
and 7,806,805.
Other patent(s) apply
& are pending
Exercise can present a
health risk. Consult a
physician before beginning
any exercise program with
this equipment. If you feel
faint or dizzy, immediately
discontinue use of this
equipment. Serious bodily
injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur
if all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
securely tightened prior to
each use. Follow all safety
instructions in this manual.
!WARNING

TABLE OF CONTENTS
Safety Instructions ...................................... 2
Before You Begin ........................................ 4
Equipment Warning & Notice Labels ........ 5
Hardware Identication Chart .................... 6
Assembly Instructions ................................ 7
Operational Instructions ........................... 10
Storage ....................................................... 15
Maintenance ............................................... 15
Conditioning Guidelines ........................... 16
Warm-Up and Cool-Down ......................... 17
Product Parts Drawing .............................. 18
Parts List ..................................................... 19
Warranty ..................................................... 21
Notes .......................................................... 22
Fax/Mail Ordering Form ............................ 23
SAFETY INSTRUCTIONS
2
1. Read all warnings and cautions posted on the AeroPilates® Performer 271.
2. The AeroPilates® Performer 271 should only be used after a thorough review of the Owner’s
Manual.
3. We recommend that two people be available for assembly of this product.
4. When exercising on this product, do not exercise at an intensity that causes the product itself to
move. This could result in damage to your joints and to the product.
5. Keep children away from the AeroPilates® Performer 271. Do not allow children to use or
play on the AeroPilates® Performer 271. Keep children and pets away from the AeroPilates®
Performer 271 when it is in use.
6. It is recommended that you place this exercise equipment on an equipment mat.
7. Set up and operate the AeroPilates® Performer 271 on a solid level surface. Do not position the
AeroPilates® Performer 271 on loose rugs or uneven surfaces.
8. Make sure that adequate space is available for access to and around the AeroPilates®
Performer 271.
9. Before using, inspect the AeroPilates® Performer 271 for worn or loose components, and
tighten or replace any worn or loose components prior to use.
10. When folding or unfolding the AeroPilates® Performer 271, keep all children away from the
AeroPilates® Performer 271 and make sure your hands are clear of any folding or pinch point.
11. Consult a physician prior to commencing an exercise program and follow his/her
recommendations in developing your tness program. If at any time during exercise you feel faint,
dizzy, or experience pain, stop and consult your physician.
12. Follow your physician’s recommendations in developing your own personal tness program.
13. Always choose the workout which best ts your physical strength and exibility level. Know your
limits and train within them. Always use common sense when exercising.
14. Do not wear loose or dangling clothing while using the AeroPilates® Performer 271.
15.Be careful to maintain your balance while using, mounting, dismounting, or assembling the
AeroPilates® Performer 271. Loss of balance may result in a fall and serious bodily injury.
16. The AeroPilates® Performer 271 should not be used by persons weighing over 300 pounds.
17. The AeroPilates® Performer 271 should be used by only one person at a time.
18. The AeroPilates® Performer 271 is for consumer use only. It is not for use in public or semipublic
facilities.
!WARNING This product contains a chemical known to the State of California to cause
cancer and birth defects or other reproductive harm.
Consult your physician before starting this or any exercise program. This is
especially important if you are over the age of 35, have never exercised before,
are pregnant, or suffer from any health problem. This product is for home use
only. Do not use in institutional or commercial applications. Failure to follow all
warnings and instructions could result in bodily injury and property damage.
The Tension Cords(10), Red Power Cord(11), and Bungee Cord(52) contain
natural rubber latex which may cause allergic reactions.
To reduce the risk of serious injury, read the following Safety Instructions
before using the AeroPilates® Performer 271.
!CAUTION
!CAUTION
!WARNING

THANK YOU FOR PURCHASING THE
AeroPilates® Performer 271
To help you get started, we have pre-assembled most of your
AeroPilates® Performer 271 at the factory with the exception
of those few parts left unassembled for shipping purposes.
Simply follow the few assembly instructions set forth in this manual.
With regular workouts, you will be getting your body into shape
and be on your way to achieving a happier and healthier lifestyle.
Should you have any questions,
please call our Customer Service Department toll-free number,
1 [phone]
Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.
Friday, 8:00 A.M. - 3:00 P.M., Central Time.
TELEPHONE
CUSTOMER SERVICE
Tel: [phone]
FAX
CUSTOMER SERVICE
Fax: [phone]
MAIL
STAMINA PRODUCTS, INC.
ATTN: Customer Service
P.O. Box 1071
Springeld, MO. 65801-1071
ONLINE
CUSTOMER SERVICE
[email protected]
www.staminaproducts.com
3
Call Us First
www.staminaproducts.com
1(800) 375-7520
Customer Service

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY:
Thank you for choosing the AeroPilates®
Performer 271. We take great pride in producing
this quality product and hope it will provide many
hours of quality exercise to make you feel better,
look better, and enjoy life to its fullest.
It's a proven fact that a regular exercise
program can improve your physical and mental
health. Too often, our busy lifestyles limit our time
and opportunity to exercise. The AeroPilates®
Performer 271 provides a convenient and simple
method to begin your assault on getting your body
in shape and achieving a happier and healthier
lifestyle.
Before reading further, please review the
drawing below and familiarize yourself with the
parts that are labeled.
Read this manual carefully before using the
AeroPilates® Performer 271.
BEFORE YOU BEGIN
Although Stamina constructs its products with
the nest materials and uses the highest standards
of manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems
with the parts included with your AeroPilates®
Performer 271, please do not return the product.
Contact us FIRST!
If a part is missing or defective, please call
us toll free at 1-800-375-7520 (in the U.S.). Our
Customer Service Staff is available to assist you
from 7:30 A.M. to 5:00 P.M. (Central Time) Monday
through Thursday and 8:00 A.M. to 3:00 P.M.
(Central Time) on Friday.
If you would like to contact us online, go to our
website at www.staminaproducts.com and access
the Customer Service section.
Be sure to have the name and model number of
the product available when you contact us.
4
Combination Wrench
Socket Wrench
Rope
Pulley Set
Hand/Foot Strap
Pulley Riser
Rear Cover
Pulley Riser
Left Pulley Hook
Right Pulley
Hook
Cardio
Rebounder
Footbar
Front Frame
Foam Pad
Headrest
Front Cover
Wheels
Locking Knob
Tension Cords
Rear Frame
Hand Grip
Rope
Hand/Foot Strap
Carriage
Cushion
Red Power Cord
Hand Grip
Front Cover
Caution
Label

Label is larger than actual size
This chart is provided to help identify the warning and notice labels on the AeroPilates® Performer
271. Please take a moment to familiarize yourself with all of the warning and notice labels.
EQUIPMENT WARNING & NOTICE LABELS
5
CAUTION LABEL(53)C1

This chart is provided to help identify the hardware used in the assembly process. Place the washers or
the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to
check the length of the bolts and screws.
NOTICE: The length of all bolts and screws, except those with flat
heads, is measured from below the head to the end of the bolt
or screw. Flat head bolts and screws are measured from the
top of the head to the end of the bolt or screw.
length
length
After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.
HARDWARE IDENTIFICATION CHART
6
mm.
in.
INCHES
MILLIMETERS
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1/2 1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6
6 8 10 12
3/16" 1/4" 5/16" 3/8" 1/2"
47 Washer (M8) 6
42 Nylock Nut (M8 x 1.25) 2
38 Screw, Round Head (M5 x 0.8 x 35mm) 4
31 Rubber Foot 4
26 Locking Knob 4
27 Plastic Wheel 2
Part No. and Description Qty

Place all parts from the box in a cleared area and position them on the oor in front of you. Remove
all packing materials from your area and place them back into the box. Do not dispose of the
packing materials until assembly is completed. Read each step carefully before beginning. If you
are missing a part please call our toll-free number for assistance 1-800-375-7520 or e-mail us at
[email protected].
ASSEMBLY INSTRUCTIONS
7
STEP 1
Remove your AeroPilates® Performer 271 from its packaging, placing the product on its side with
the LOCKING PIN(28) side upward. Remove the LOCKING PIN(28) and unfold the MAIN FRAME
ASSEMBLY separating the half that has the attached LOCKING PIN(28). When completed, the frame
should form a "V" with the frame ends separated approximately three feet.
STEP 2
Attach the four RUBBER FEET(31) to the FRONT FRAME(1) and REAR FRAME(2) with ROUND HEAD
SCREWS(M5x0.8x35mm)(38). The ROUND HEAD SCREWS(M5X0.8X35mm)(38) are already in the
RUBBER FEET(31). Attach the PLASTIC WHEELS(27) to the FRONT FRAME(1) with WASHERS(M8)
(47) and NYLOCK NUTS(M8)(42).
STEP 3
Unfold your AeroPilates® Performer 271 to a flat position by moving the FRONT FRAME(1) away
from the platform end of the REAR FRAME(2) in a clockwise position until fully extended. Lower the
AeroPilates® Performer 271 so all four RUBBER FEET(31) are at on the oor.

ASSEMBLY INSTRUCTIONS
8
STEP 4
Remove the paper covering from the foam tape inside the FRONT COVER(3) and REAR COVER(4).
Place the FRONT COVER(3) over the FRONT FRAME(1). Place the REAR COVER(4) over the REAR
FRAME(2). Press the covers securely in place.
STEP 5
Insert the PULLEY RISERS(25) into the mounting holes in the REAR COVER(4) and REAR FRAME(2). Insert
the PULLEY RISERS(25) all the way to the bottom, align the threaded holes in the PULLEY RISERS(25)
with the holes in the REAR FRAME(2), and lock the PULLEY RISERS(25) in position with the LOCKING
KNOBS(26).
STEP 6
Refer to the detail drawing below showing an enlarged view of the left PULLEY RISER(25) and the LEFT
PULLEY HOOK(23). With the pulley facing down, insert the LEFT PULLEY HOOK(23) into the left PULLEY
RISER(25) from the inside as shown. Swing the pulley forward as shown and the LEFT PULLEY HOOK(23)
will be in position for use. Use the same procedure to install the RIGHT PULLEY HOOK(24) on the right
PULLEY RISER(25).

ASSEMBLY INSTRUCTIONS
9
STEP 7
Insert the FOAM PAD ASSEMBLIES(17) into the holes located on the CARRIAGE(7). Place the HAND/
FOOT STRAPS(20) over the FOAM PAD ASSEMBLIES(17) for storage.
STEP 8
Make sure that the threaded holes in the CARDIO REBOUNDER(50) are facing toward the end of the
AeroPilates® Performer 271 as shown in the illustration. Insert the CARDIO REBOUNDER(50) into the
mounting holes located in the FRONT FRAME(1). Insert the CARDIO REBOUNDER(50) all the way to the
bottom and lock it in place with the LOCKING KNOBS(26).
NOTE: You can choose to insert the FOOTBAR(5) into the FRONT FRAME(1) and lock in position with
the LOCKING KNOBS(26). Refer to the inset drawing.

OPERATIONAL INSTRUCTIONS
10
HEADREST ADJUSTMENT
The HEADREST(15) on the CARRIAGE(7) can be
positioned at an incline by simply pivoting the SUPPORT
BRACKET underneath the HEADREST(15).
ROPE LENGTH ADJUSTMENT
The ROPES(18) feed through the PULLEY SETS(22) then
thread through the loops on the underside of both outer
edges of the CARRIAGE(7). PLASTIC SNAP HOOKS(19)
on the end of each rope are used to adjust the ROPE(18)
length. If more length is needed, as when performing some
leg exercises, then attach the PLASTIC SNAP HOOKS(19)
to loop D. To shorten, as when performing some arm
exercises, then bring the ROPES(18) around the last loop
Dand secure to loops A, B, or C with the PLASTIC SNAP
HOOKS(19). Wrap the ROPES(18) around and through
the loops again and attach where needed to shorten
ROPES(18) even more.
LOAD ADJUSTMENT
There are two TENSION CORDS(10) and one heavier RED
POWER CORD(11).
The resistance of the CARRIAGE(7) can be adjusted by
securing the TENSION CORDS(10, 11) in the slots located
on the FRONT FRAME(1). You can achieve various levels
of resistance by securing different numbers of the TENSION
CORDS(10, 11) in the slots.
NOTE: To achieve greater resistance in the RED POWER
CORD(11) and TENSION CORDS(10), stretch and
re-tie the tension cords in a more taut position.
B
C
D
Support
Bracket
SLOTS
A

OPERATIONAL INSTRUCTIONS
11
Ideal rope length will vary depending on your height and limb length. To determine your ideal rope length,
begin by placing the hand/foot straps over the shoulder rests as shown below. Adjust the ropes so they are
taut. For complete rope length adjustment instructions, see additional Rope Length Adjustment instructions
in this Owner’s Manual.
Next, lie on the reformer with your hands in the straps with shoulders against the shoulder rests. Reach
your hands toward the ceiling until they are directly over the back edge of the reformer carriage as shown
in below. In this position, the reformer carriage should be at rest with no tension on the ropes. If there is
still tension on the ropes in this position, lengthen the ropes. If you lose tension before reaching the arm
position shown below, shorten the ropes.
CUSTOMIZING ROPE LENGTH

OPERATIONAL INSTRUCTIONS
12
Standard Setting- the top hole
The standard height setting for the reformer pulleys is the top setting. At the top setting, the pull of the ropes
provides the most support and feedback for the body. Place your pulleys at the top setting to most easily
achieve proper form and to recruit the core muscles.
Variable settings- lower four holes
You can add variety to your routine by using different pulley settings. The lower you set the pulleys, the
less guidance and support you receive from the ropes. By providing less guidance and support, the lower
settings further challenge strength and coordination.
PULLEY HEIGHT ADJUSTMENT

OPERATIONAL INSTRUCTIONS
13
RESISTANCE CORD STRENGTH
The approximate maximum resistance provided by each cord is outlined in the chart below. Frequency of
use, type of use and user weight will have an effect on the strength of your cords. Over time cord strength
will gradually decrease. Replacement cords are available for purchase at www.staminaproducts.com.
The AeroPilates®workout wall chart and workout DVDs indicate which cords to use for each exercise.
To replace or add a tension cord, rst carefully release the carriage and tip your machine on its side. Untie
the knot that secures the cord you are replacing and simply pull it out. Thread the new cord through the
metal holes from the end of the carriage to the other end.
Pull tightly on the cord stretching it to the point that allows you to tie a double knot, and release the cord
into place.
TENSION CORD SELECTION
TENSION CORD REPLACEMENT
TENSION
CORDS
BLACK
RED
approximately 24 pounds
approximately 34 pounds
CORD RESISTANCE
1 2 3 4

OPERATIONAL INSTRUCTIONS
14
To replace a carriage wheel, rst remove the carriage by releasing the cords and sliding the carriage all
the way back to the top end or rear frame of the machine. Tip your machine on its side, bend the machine
at the hinge, and simply slide the carriage off the frame.
Turn the carriage upside down so it is cord side up. Using a crescent wrench and at head screwdriver,
remove the screw that is holding the wheel in place. Replace the old wheel with the new one, add the
washer, push the screw through the wheel and tighten with the nut.
CARRIAGE WHEEL REPLACEMENT
You can nd use and maintenance instructional video clips at www.staminaproducts.com.
WEBSITE RESOURCES
1234

The safety and integrity designed into the AeroPilates® Performer 271 can only be maintained when
the AeroPilates® Performer 271 is regularly examined for damage and wear. Special attention should
be given to the following:
STORAGE
MAINTENANCE
15
1. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
2. Worn or damaged components should be replaced immediately or the AeroPilates® Performer 271
should be removed from service until repair is made.
3. Verify that the CAUTION LABEL(53) is in place and easy to read. Call Stamina Products immediately
at 1-800-375-7520 for a replacement CAUTION LABEL(53) if it is missing or damaged.
4. Verify that the ROPES(18) are properly installed on the PULLEY SETS(22).
5. Check the condition of the ROPES(18) and replace if they are frayed or worn.
6. Check the PLASTIC SNAP HOOKS(19) on the ends of the ROPES(18). Replace the PLASTIC
SNAP HOOKS(19) if they are damaged or deformed.
7. Check the TENSION CORDS(10, 11). If any of the TENSION CORDS(10, 11) are stretched and
loose, re-tie the knot on the end of the cord. Replace TENSION CORDS(10, 11) that are frayed or
worn.
8. Check the BUNGEE CORD(52) on the CARDIO REBOUNDER(50) for wear. Replace the BUNGEE
CORD(52) if it is frayed or worn.
9. Check the PULLEY SETS(22) for excessive wear. Replace worn PULLEY SETS(22).
10. Check the HAND/FOOT STRAPS(20) for damage. Replace damaged parts.
11. Check the FOAM SLEEVE(6) and FOAM PADS(17) and replace if damaged or worn.
12. Check the STOP PLATES(29) for looseness or damage and replace any damaged parts.
13. Check the CUSHION(14) and replace if it is damaged or worn.
14. Check and clean the ROLLERS(8) and the rolling surfaces on the rails. Clean by wiping with a dry
cloth.
15. Only Stamina Products supplied components shall be used to maintain/repair the AeroPilates®
Performer 271.
16. Keep your AeroPilates® Performer 271 clean by wiping it off with an absorbent cloth after use.
1. To store the AeroPilates® Performer 271, simply keep it in a clean dry place.
2. The FRONT FRAME(1) of the AeroPilates® Performer 271 has built-in wheels for easy moving. To
move, be sure at least one of the tension cords is attached to prevent the CARRIAGE(7) from sliding,
then lift from the end of the REAR FRAME(2) and roll.
3. The AeroPilates® Performer 271 folds for storage. To fold, be sure no tension cords are attached
and slide the CARRIAGE(7) to the end of the REAR FRAME(2). Remove the FOOTBAR(5), CARDIO
REBOUNDER(50), and FOAM PAD ASSEMBLIES(17), then lift the AeroPilates® Performer 271
onto its side with the LOCKING PIN(28) side up. With the machine hinging in the middle, move the
FRONT FRAME(1) toward the REAR FRAME(2) until the frame ends meet. Insert the LOCKING
PIN(28) into the hole in the REAR FRAME(2), and the AeroPilates® Performer 271 is ready to
store.

How you begin your exercise program depends on your physical condition. If you have been inactive for
several years or are severely overweight, start slowly and increase your workout time gradually. Increase
your workout intensity gradually by monitoring your heart rate while you exercise.
Initially you may only be able to exercise within your target zone for a few minutes; however, your aerobic
capacity will improve over the next six to eight weeks. It is important to pace yourself while you exercise
so you don't tire too quickly.
Measure your heart rate periodically during your workout by stopping the
exercise but continuing to move your legs or walk around. Place two or
three ngers on your wrist and take a six second heartbeat count. Multiply
the results by ten to nd your heart rate. For example, if your six second
heartbeat count is 14, your heart rate is 140 beats per minute. A six second
count is used because your heart rate will drop rapidly when you stop
exercising. Adjust the intensity of your exercise until your heart rate is at the
proper level.
wrist pulse
Remember to follow these essentials:
Have your doctor review your training and diet programs.
Begin your training program slowly with realistic goals that have been set by you and your physician.
Warm up before you exercise and cool down after you work out.
Take your pulse periodically during your workout and strive to stay within a range of 60% (lower
intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower intensity, and
build up to higher intensity as you become more aerobically t.
If you feel dizzy or lightheaded you should slow down or stop exercising.
To determine if you are working out at the correct intensity, use a heart rate monitor or use the table
below. For effective aerobic exercise, your heart rate should be maintained at a level between 60%
and 90% of your maximum heart rate. If just starting an exercise program, work out at the low end of
your target heart rate zone. As your aerobic capacity improves, gradually increase the intensity of your
workout by increasing your heart rate.
CONDITIONING GUIDELINES
Target Heart Rate Zone Estimated by Age*
* For cardiorespiratory training benefits, the American College of Sports Medicine recommends
working out within a heart rate range of 55% to 90% of maximum heart rate. To predict the
maximum heart rate, the following formula was used: 220 - Age = predicted maximum heart rate
20 years
25 years
30 years
35 years
40 years
45 years
50 years
55 years
60 years
65 years
70 years
Average Maximum
Heart Rate 100%
Age
110-180 beats per minute
107-175 beats per minute
105-171 beats per minute
102-166 beats per minute
99-162 beats per minute
97-157 beats per minute
94-153 beats per minute
91-148 beats per minute
88-144 beats per minute
85-139 beats per minute
83-135 beats per minute
200 beats per minute
195 beats per minute
190 beats per minute
185 beats per minute
180 beats per minute
175 beats per minute
170 beats per minute
165 beats per minute
160 beats per minute
155 beats per minute
150 beats per minute
Target Heart Rate Zone
(55%-90% of Maximum Heart Rate)
16

WARM-UP and COOL-DOWN
Warm-Up The purpose of warming up is to prepare your body for exercise and to minimize injuries.
Warm up for two to ve minutes before strength training or aerobic exercising. Perform activities that
raise your heart rate and warm the working muscles. Activities may include brisk walking, jogging,
jumping jacks, jump rope, and running in place
Stretching Stretching while your muscles are warm after a proper warm-up and again after your
strength or aerobic training session is very important. Muscles stretch more easily at these times
because of their elevated temperature, which greatly reduces the risk of injury. Stretches should be held
for 15 to 30 seconds. Do not bounce.
Suggested Stretching Exercises
Remember to always check with your physician before starting any exercise program.
Cool-Down The purpose of cooling down is to return the body to its normal, or near normal, resting
state at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows
blood to return to the heart. Your cool-down should include the stretches listed above and should be
completed after each strength training session.
Lower Body Stretch
Place feet shoulder-width
apart and lean forward.
Keep this position for 30
seconds using the body as a
natural weight to stretch the
backs of the legs.
DO NOT BOUNCE!
When the pull on the back of
the legs lessens, gradually
try a lower position.
Floor Stretch
While sitting on the oor,
open the legs as wide as
possible. Stretch the upper
body toward the knee on the
right leg by using your arms
to pull your chest to your
thighs. Hold this stretch 10
to 30 seconds.
DO NOT BOUNCE!
Do this stretch 10 times.
Repeat the stretch with the
left leg.
Bent Over Leg Stretch
Stand with feet shoulder-
width apart and lean forward
as illustrated. Using the
arms, gently pull the upper
body towards the right leg.
Let the head hang down.
DO NOT BOUNCE!
Hold the position a minimum
of 10 seconds. Repeat
pulling the upper body to
the left leg. Do this stretch
several times slowly.
Bent Torso Pulls
While sitting on the oor,
have legs apart, one leg
straight and one knee bent.
Pull the chest down to touch
the thigh on the leg that is
bent, and twist at the waist.
Hold this position at least 10
seconds. Repeat 10 times
on each side.
17

PRODUCT PARTS DRAWING
18
FRONT
BACK

PART# PART NAME QTY
1 Front Frame 1
2 Rear Frame 1
3 Front Cover 1
4 Rear Cover 1
5 Footbar 1
6 Foam Sleeve 1
7 Carriage 1
8 Roller 4
9 Roller Spacer 4
10 Tension Cord 2
11 Red Power Cord 1
12 Support Bushing 3
13 Stop Bushing 3
14 Cushion 1
15 Headrest 1
16 Foam Pad Tube 2
17 Foam Pad 2
18 Rope 2
19 Plastic Snap Hook 2
20 Hand/Foot Strap 2
21 Hand Grip 2
22 Pulley Set 2
23 Left Pulley Hook 1
24 Right Pulley Hook 1
25 Pulley Riser 2
26 Locking Knob 4
27 Plastic Wheel 2
28 Locking Pin 1
29 Stop Plate 4
30 Stop Pad 4
31 Rubber Foot 4
32 Round Plug (25mm) 4
33 Rubber Stand 2
34 Screw, Flat Head (M5 x 0.8 x 16mm) 2
35 Shaft Bolt, Socket Head (M8 x 1.25 x 20mm) 2
36 Bolt, Socket Head (M6 x 1 x 14mm) 8
37 Bolt, Round Head (M8 x 1.25 x 25mm) 4
38 Screw, Round Head (M5 x 0.8 x 35mm) 4
39 Screw, Flat Head (M5 x 0.8 x 25mm) 3
40 Acorn Nut (M5 x 0.8) 4
41 Nylock Nut (M6 x 1) 8
42 Nylock Nut (M8 x 1.25) 6
43 Nylock Nut (M5 x 0.8) 9
44 Nut (M8 x 1.25) 4
45 Washer (M5) 9
46 Washer (M6) 8
47 Washer (M8) 14
PARTS LIST
19

48 Washer (M10) 4
49 Lock Washer (M8) 4
50 Cardio Rebounder 1
51 Mat 1
52 Bungee Cord 1
53 Caution Label 1
54 Combination Wrench 1
55 Socket Wrench 1
56 Manual 1
57 Workout Chart 1
58 Introduction to AeroPilates®/
AeroPilates® Level One Pure Pilates Workout (DVD) 1
59 AeroPilates® Level One Simply Cardio Workout/
AeroPilates® Level One Integrated Workout (DVD) 1
PART# PART NAME QTY
PARTS LIST
20