Members Mark TM130837 User manual

1
4 Foot Glider Bench
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
THIS ASSEMBLY MANUAL CONTAINS IMPORTANT SAFETY INFORMATION.
Assembly Manual
Model Number: TM130837

2
Important Safety Information
Please read all instructions carefully before assembling this furniture.
For your safety, assembly by two or more adults is strongly recommended.
Use only vendor-supplied hardware to assemble this item. Using unauthorized
hardware could jeopardize the structural integrity of the item.
Hardware may loosen overtime. Periodically check that all connections are tight.
·
·
·
·
Before Assembly
Remove all parts and hardware from the box. Place all items on a carpeted or
scratch-free work surface, as this will avoid damaging parts during assembly.
The shipping box provides an ideal work surface.
To avoid accidentally discarding small parts or hardware, do not dispose of any
packaging or contents of the shipping carton until assembly is complete.
Use the parts and hardware lists below to identify and separate each of the
pieces included.
The use of power tools for assembly is not recommended. Power tools can
damage the hardware and/or split the wood.
Note: Do not fully tighten all bolts until all parts are in place. Failure to follow
these instructions may cause the bolts to misalign during assembly.
·
·
·
·
·
·
Care & Maintenance :
To increase the item lifespan, avoid leaving the furniture in standing water or
indirect contact with wet ground.
Cover or move the furniture into covered storage during inclement weather and
during winter months.
Clean periodically with soft flannel cloth, slightly dampened with a mild soap
solution and warm water. DO NOT use abrasive material, bleach or scouring
products as this will affect the finish. Dry throughly with soft cloth.
·
·
·

3
1 3/4" Bolt
Qty: 8 Pcs + 1
Phillips Screwdriver ( not included ).
Tools Needed for Assembly
Hardware
(F)
Need assistance? Visit us at: samsclub.com/membersmarkhelp
Component
A1 ............ Right side frame ..............
A2 ............ Left side frame .................
B .............. Back support ....................
C .............. Seat ....................................
D1 ............ Right base side frame ......
D2 ............ Left base side frame ........
E .............. Base cross bar ..................
A1 A2 B
2" Bolt
Qty: 2 Pcs + 1
(G)
Gliding stretch
Qty: 4 Pcs
(J)
Washer
Qty: 8 Pcs + 1
(K)
Rubber mallet ( not included ).
2 3/4" Bolt
Qty: 8 Pcs
(H)
(L)
Nut
Qty: 8 Pcs + 1
(I)
Wrench ( included ).
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
2 pcs
D2 E
Wooden cap
Qty: 10 Pcs + 2

1
BACK FRONT
LONG
FOOT-LEG
SHORT
FOOT-LEG
F
L
L
F
UP
EBACK
FRONT
D1
D2
K
LL
7
Attach base cross bars (E) into right and left base side frame
(D1&D2) and secure using 1 3/4" bolts (F).
Tighten all bolts completely using screwdriver before tapping in
the wooden caps (L).
2
Attach the right side frame (A1) into back support (B).
Secure with 1 3/4" bolt (F).
** Do not tighten the bolts yet.
FRONT
3
A1
C
Next, attach the seat (C) into predrilled holes of right side
frame (A1).
Secure with 1 3/4" bolt (F) and 2" bolt (G), position as shown .
F
G
4
F
G
A2
Attach the left side frame (A2) into the assembly from step 3. Secure with 1 3/4" bolts (F) and 2" bolt (G), using screwdriver .
5
H
I
J
A2
A1 K
Assemble gliding stretches (K) into leg frames (A1&A2) and secure using 2 3/4" bolts (H), washer (J) and nuts (I)
as diagram shown.
Tighten the nuts and bolts using wrench (included).
BACK
FRONT
Attach the previously assembled base side frames (D1&D2) to the leg frames (A1&A2).
Connect using gliding stretches (K) to the leg frames (A1&A2) and secure using 2 3/4" bolts (H), washers (J), nut (I)
as diagram shown. Tighten the nuts and bolts using wrench.
A1
A2
D1 D2
6
- Make sure all parts are correctly connected and tighten all bolts and nuts using screwdriver and wrench.
Tipping in the wooden caps (L) to cover bolts head using rubber mallet.
** Apply a drop oil (not supplied) on gliding stretch for smoother operation if needed.
FRONT
FRONT
HJ
I
4
Need assistance? Visit us at: samsclub.com/membersmarkhelp 5
Need assistance? Visit us at: samsclub.com/membersmarkhelp
F
FRONT
B
A1
FRONT
1 3/4" Bolt
Qty: 4 Pcs
(F) Wooden cap
Qty: 4 Pcs
(L)
1 3/4" Bolt
Qty: 1 Pc
(F) 2" Bolt
Qty: 1 Pc
(G)
1 3/4" Bolt
Qty: 2 Pcs
(F) 2" Bolt
Qty: 1 Pc
(G)
1 3/4" Bolt
Qty: 1 Pc
(F)
2 3/4" Bolt
Qty: 4 Pcs
(H) Gliding stretch
Qty: 4 Pcs
(K)
Washer
Qty: 4 Pcs
(J)
Nut
Qty: 4 Pcs
(I)
2 3/4" Bolt
Qty: 4 Pcs
(H) Washer
Qty: 4 Pcs
(J)
Nut
Qty: 4 Pcs
(I)
Wooden cap
Qty: 6 Pcs
(L)