Home Styles 88 5180 26 User manual

Tools required for assembly : Phillips screwdriver
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
Home Styles ConsumerAssistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Hardware List
88 5180 26
Upholstered Bench
A.
Cushion
1 Pc.
B.
Top
1 Pc.
C.
Side Panel
1 Pc.
E.
Middle Panel
1 Pc.
D.
Side Panel
1 Pc.
F.
Base
1 Pc.
G.
Back Panel
1 Pc.
K.
Door
1 Pc.
H.
Leg
4 Pcs.
J.
Door
1 Pc.
I.
Leg
1 Pc.
Hex Wrench
1 Pc. Small Hex Wrench
1 Pc. Head Cap Bolt (short) 12 Pcs.(+1 extra) Head Cap Bolt (long) 8 Pcs.(+1 extra)
Magnet
2 Pcs.
Spring Washer
20 Pcs.(+1 extra) Flat Washer
20 Pcs.(+1 extra) Wood Screw
(for Magnet)
4 Pcs.(+1 extra)
Wood Screw
(long)
8 Pcs.(+1 extra)
Wood Screw
(short)
8 Pcs.(+1 extra)
One Left Support
One Right Support
2 Pcs.
Manchine Screw
4 Pcs.
Pull Handle
2 Pcs.
Tools recommended for assembly : Level

Assembly Instructions 2
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the Head Cap Bolts until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
B
G
B
B
B
E
B
C
B
D
B
H
B
H
B
H
B
H
B
I
B
F
STEP 2
Attach Base (F) to unit with
Head Cap Bolts (short),
Spring Washers and Flat Washers.
Tighten all Head Cap Bolts.
Attach Legs (H) and (I) to unit with
Head Cap Bolts (long), Spring Washers and Flat Washers. (see Figure 2)
Wood Screw (for Magnet)
Magnet
STEP 1
Place Top (B)
upside down
on a soft cloth.
Attach Magnets to Top (B) at the pre-drilled holes
of Top (B) with Wood Screws (for Magnet).
(see Figure 1)
Attach Side Panels (C) and (D) and Middle Panel (E) to
Top (B) with Head Cap Bolts (short), Spring Washers and
Flat Washers.
Tighten all Head Cap Bolts only half way.
Slide Back Panel (G) into position.
Figure 1
Figure 2
Head Cap Bolt (short)
Spring Washer
Flat Wacher
Head Cap Bolt (short)
Spring Washer
Flat Wacher Flat Wacher
Spring Washer
Head Cap Bolt (long)
/4

B
K
B
J
Figure 4
Figure 3
Assembly Instructions 3
STEP 4
Turn the unit over to its’ upright position.
Attach Doors (J) and (K) to unit by inserting the door hinges into
the slots in unit and attach with Wood Screws (long).
(see Figure 4)
STEP 3
Attach Pull Handles to Doors (J) and (K) with
Machine Screws. (see Figure 3)
/4
Wood Screw
(long) Hinge

/3
Figure 7
STEP 6
To level the unit, adjust the adjustable levelers
on the bottom of the legs.
(see Figure 7)
Assembly Instructions 4
Wood Screw
(short)
Left Support
Right Support
STEP 5
Attach Supports to unit with Wood Screws (short) into
the pre-drilled holes. (see Figures 5 and 6)
Place Cushion (A) into position.
Figure 5 Figure 6
B
A
/4