Stanley TLM210 User manual

77-921

min
max
?
1
2
3
4
5
6
78
10
11
12
9

D
GB
F
I
E
P
NL
DK
S
N
FIN
J
CN
ROK
PL
HR
H
RUS
CZ
GR
1Start-up
Stanley TLM 210 1.0.0 gb
User Manual
Version 1.0
English
Congratulations on your purchase of a Stanley TLM 210.
The safety instructions can be
found in a separate booklet, which
accompanies this user manual. The
safety instructions along with the
user manual should be read carefully before initial
operation.
Helpful Hint: The first and last page including the
pictures should be folded out and left open, whilst
reading through the manual. Letters and Numbers in
braces {} refer to the illustrations.
Content
Start-up................................................................1
Operation.............................................................2
Measuring ............................................................3
Functions .............................................................3
Appendix ..............................................................4
Start-up
Inserting / Replacing Batteries
See figure {C} - Push locking mechanism to the right
and push the cover of the battery compartment
downwards and open it. Place the batteries in the
compartment making sure they are correctly inserted.
Push the cover of the compartment back and let it
lock in place.
The battery symbol {B, 4} appears permanently
blinking in the display when the battery voltage is too
low. The batteries should be replaced as soon as
possible.
• Pay attention to correct polarity.
•Usealkalinebatteries.
• Batteries should be removed if the device will not
be used for a long time (danger of corrosion).
When changing the batteries the settings and stack
content remain unchanged.

D
GB
F
I
E
P
NL
DK
S
N
FIN
J
CN
ROK
PL
HR
H
RUS
CZ
GR
2
Operation Stanley TLM 210 1.0.0 gb
Keypad
See figure {A}:
1ON/MEASURING
2PLUS +
3AREA/VOLUME
4HISTORY/UNITS
5CLEAR/OFF
6MEASUREMENT REFERENCE
7MINUS -
Display
See figure {B}
1 Information about faulty measurement
2Laser"ON"
3 Measurement reference (front / rear)
4 Battery indication
5Area/Volume
6 Hardware error
7 Main line
8 Units with exponents (2/3)
9 Minimum value of continuous measurement
10 Three auxiliary lines (e.g. previous values)
11 Maximum value of continuous measurement
12 Stack recall
Selecting Units
Press UNITS - key {A, 4} long to select desired unit.
Possible units:
Operation
Switching On/Off
ON: Press ON - key {A, 1} briefly. The laser is
active. Battery indication is displayed until the
next keystroke.
OFF: Press and hold OFF - key {A, 5}. To maximize
battery life the device will automatically turn
off after 3 minutes of inactivity.
Distance Area Volume
0.000 m 0.000 m² 0.000 m³
0.00 m 0.00 m² 0.00 m³
0.00 ft 0.00 ft² 0.00 ft³
0.00 1/16 ft in 0.00 ft² 0.00 ft³
0' 0'' 1/16 0.00 ft² 0.00 ft³
0.0 in 0.00 ft² 0.00 ft³
0 1/16 in 0.00 ft² 0.00 ft³

D
GB
F
I
E
P
NL
DK
S
N
FIN
J
CN
ROK
PL
HR
H
RUS
CZ
GR
3Measuring
Stanley TLM 210 1.0.0 gb
CLEAR Key
Pushing the CLEAR - key {A, 5} clears the last entry
or measurement. Within a function (area, volume,
etc.) single measurements can be deleted step by
step and re-measured.
Illumination
The display backlight remains on for 15 seconds after
the last key press.
Measuring Reference
The default reference setting is from the rear of the
instrument. By pressing the REFERENCE - key {A, 6},
the setting can be changed, so that the next
measurement taken will be from the "front" of the in-
strument. Afterwards the reference setting automat-
ically defaults back to rear. See picture {D}. By
pressing REFERENCE - key {A, 6} long, the reference
setting will stay from the "front" of the instrument.
Repeated pressing of the REFERENCE - key {A, 6} will
set the instrument to its default reference setting.
Measuring
Single Distance Measuring
Pressing ON/MEASURING - key {A, 1} turns the laser
on. Aim at the desired target and press ON/MEASU-
RING - key {A, 1} again. The measured distance is
displayed immediately in the chosen unit.
Minimum/Maximum Measuring
This function allows the user to measure the
minimum or maximum distance from a fixed
measuring point as well as to determine spacing - see
figure {E}. It is commonly used to measure a diagonal
distance (maximum value) or a horizontal distance
(minimum value).
Press and hold ON/MEASURING - key {A, 1} until you
hear a beep, indicating the device is in a continuous
measuring mode. Then slowly sweep the laser back
and forth respectively up and down over the desired
target point - see figure {F, G} - (e.g. a corner in the
room).
Press ON/MEASURING - key {A, 1} again and the
continuous measurement will be stopped. The
current values for maximum and minimum distances
are shown in the display as well as the last measured
value in the main line.
Functions
Addition / Subtraction
Take the first measurement, addition is executed by
pressing the PLUS - key {A, 2} and subtraction by
pressing the MINUS - key {A, 7}, then take the next
measurement. This process can be repeated as many
times as is required. The result is displayed in the
main line, whilst the last measurement taken is also
displayed. Pushing the CLEAR - key {A, 5} undoes the
last step.

D
GB
F
I
E
P
NL
DK
S
N
FIN
J
CN
ROK
PL
HR
H
RUS
CZ
GR
4
Appendix Stanley TLM 210 1.0.0 gb
Areas and volumes can be added / subtracted in
exactly the same manner.
Area
Press AREA/VOLUME - key {A, 3}. The corresponding
symbol {B, 5} appears in the display. The first side to
be measured flashes on the display. Take the two
measurements, the result will be displayed in the
main line.
Volume
Press AREA/VOLUME - key {A, 3} twice. The corre-
sponding symbol {B, 5} appears in the display. The
first distance to be measured flashes on the display.
When 3 measurements have been taken the result
will be displayed in the main line.
HISTORY
Pressing the HISTORY - key {A, 4} shows the last 19
displays in reverse order. Using the PLUS - key {A, 2}
and the MINUS - key {A, 7} allows to navigate in the
historical storage.
In order to leave the history press either CLEAR - key
{A, 5}, ON/MEASURING - key {A, 1} or the AREA/
VOLUME - key {A, 3}. Press and hold the HISTORY -
key {A, 4} until a beep, allows the user to take the
selected result to carry on with calculations.
Appendix
Message Codes
All message codes will be displayed with either "InFo"
or "Error".
The following mistakes can be corrected:
InFo Cause Remedy
204 Calculation error Repeat procedure
252 Temperature too
high Cool down instrument
253 Temperatur too low Warm up instrument
255 Receiver signal too
weak, measurement
time too long,
distance > 100 m
Use target plate
256 Received signal too
powerful Use target plate (grey side)
257 Wrong measure-
ment, ambient
brightness too high
Use target plate
(brown side)
260 Laser beam inter-
rupted Repeat measurement
Error Cause Remedy
Hardware error Switch on/off the
device several times
and check if the
symbol still appears. If
so please call your
dealer for assistance.

D
GB
F
I
E
P
NL
DK
S
N
FIN
J
CN
ROK
PL
HR
H
RUS
CZ
GR
5Appendix
Stanley TLM 210 1.0.0 gb
Technical Data
* maximum deviation occurs under unfavourable conditions
such as bright sunlight or when measuring to poorly
reflecting or very rough surfaces. For distances over 30 m -
without using a target plate - the maximum deviation may
increase by ± 0.1 mm/m to a maximum of ± 10 mm
Measuring Conditions
Measuring Range
At night, at dusk and when the target is shadowed
the measuring range without target plate is
increased.
Use a target plate to increase the measurement
range during daylight or if the target has a bad reflec-
tion.
Measuring Surfaces
Measuring errors can occur when measuring toward
colourless liquids (e.g. water) or dust free glass,
styrofoam or similar semi-permeable surfaces.
Aiming at high gloss surfaces deflects the laser beam
and measurement errors can occur.
Against non-reflective and dark surfaces the
measuring time can be increased.
Care
Do not immerse the unit in water. Wipe off dirt with
a damp, soft cloth. Do not use aggressive cleaning
agents or solutions. Treat the optical surfaces with
the same care that you would apply to eyeglasses
and cameras.
Range
From about 70 m, use target plate.
Range (use target plate
for longer distances) 0.05 m to 100 m 0.2 ft to 328 ft
Measuring accuracy up
to 30 m (2 σstandard
deviation)
typ.: ± 3 mm*
Smallest unit displayed 1 mm
Laser class II
Laser type 635 nm, < 1 mW
Ø laser spot
(at distance) 6 / 30 / 60 mm (10 / 50 / 100 m)
Automatic switch off after 180 s
Illumination 9
Minimum, maximum
measuring
9
Addition, Subtraction
(+/-)
9
Historical storage 9(19)
Battery life,
Type AAA, 2 x 1.5 V up to 5 000 measurements
IP rating IP 54 acc. IEC529
splash proof, dust proof
Dimension and weight 135x55x34 mm, ~150 g
Temperature range:
Storage
Operating
-25°C to +70°C
(-13°F to +158°F)
-10°C to +50°C
(-14°F to +122°F)

D
GB
F
I
E
P
NL
DK
S
N
FIN
J
CN
ROK
PL
HR
H
RUS
CZ
GR
6
Appendix Stanley TLM 210 1.0.0 gb
Warranty
The Stanley TLM 210 comes with a two (2) year
warranty from Stanley Works. For more information
on the warranty please go to:
www.stanleyworks.com.
In case of any questions concerning the warranty
please contact the dealer who you purchased the
instrument from.
All illustrations, descriptions and technical specifica-
tions are subject to change without prior notice.

LCA746653