Stanley Genesis 07537 User manual

07537
07537
Genesis® 07537
Hydro-Pneumatic Power Tool
Instruction Manual
Original Instruction
Hydro-Pneumatic
Power Tool
Original Instructions
Traduction du manuel original
Oversættelse af de originale instruktioner
Alkuperäisen ohjeen käännös
Vertaling van de originele handleiding
Tradução das instruções originais
Übersetzung der Original-Betriebsanleitung
Oversettelse av de originale instruksjoner
Trauzione delle instruzioni originali
Översättning av ursprungliga instruktioner
Instrucciones Originales
English
French
Danish
Finish
Dutch
Portuguese
German
Norwegian
Italian
Swedish
Spanish

3
Contents
Safety Rules 4
Specifications
Specification for 7537 Tool 5
Tool Dimensions 5
Intent of Use 6
Putting into Service
Air Supply 7
Mechanical Cursors 8
Cursor 9
Loading and Reloading the Tool 9
Loading the Tool 10
Reloading the Tool 10
Operating Procedure 10
Mandrel Follower Springs Identification 11
and Orientation
Nose Assemblies
Nose Jaws 12
Selecting a Nose Jaw 13
Nose Jaw Selection - Imperial 14
Nose Jaw Selection - Metric 15
Mandrels and Mandrel Follower Springs 16
Chobert®and Grovit®- Imperial 16
Chobert®and Grovit®- Metric 17
Briv®- Imperial 18
Mandrel Head Types and ‘P’ Length 19
Briv®- Metric 19
Avlug®, Avsert®, Avtronic®and Rivscrew®
Imperial and Metric 20
Servicing the Tool
Daily 21
Weekly 21
MolyLithium Grease EP 3753 Safety Data 21
Molykote®55m Grease Safety Data 22
Molykote®111 Grease Safety Data 22
Service Kits 23
Maintenance
Dismantling 07537-00200 24-25
General Assembly and Parts List 07537-00200 26-27
Priming
Oil Details 28
Hyspin®VG 32 and AWS 32 Oil Safety Data 28
Priming Pump 28
Priming Procedure 29
Fault Diagnosis
Symptom, Possible Cause and Remedy 30
LIMITED WARRANTY
Avdel makes the limited warranty that its products will be free of defects in workmanship and materials
which occur under normal operating conditions. This Limited Warranty is contingent upon: (1) the product
being installed, maintained and operated in accordance with product literature and instructions, and (2) confirmation by Avdel of
such defect, upon inspection and testing. Avdel makes the foregoing limited
warranty for a period of twelve (12) months following Avdel’s delivery of the product to the direct purchaser
from Avdel. In the event of any breach of the foregoing warranty, the sole remedy shall be to return the
defective Goods for replacement or refund for the purchase price at Avdel’s option. THE FOREGOING
EXPRESS LIMITED WARRANTY AND REMEDY ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES
AND REMEDIES. ANY IMPLIED WARRANTY AS TO QUALITY, FITNESS FOR PURPOSE, OR MERCHANTABILITY
ARE HEREBY SPECIFICALLY DISCLAIMED AND EXCLUDED BY AVDEL.
Avdel UK Limited policy is one of continuous product development and improvement and we reserve the right to change the specification of any product without prior notice.

4
Safety Rules
This instruction manual must be read with particular attention to the following safety rules, by any person installing,
operating, or servicing this tool.
1Do not use outside the design intent.
2Do not use equipment with this tool/machine other than that recommended and supplied by Avdel UK Limited.
3Any modification undertaken by the customer to the tool/machine, nose assemblies, accessories or any equipment supplied by Avdel UK Limited. or
their representatives, shall be the customer’s entire responsibility. Avdel UK Limited. will be pleased to advise upon any proposed modification.
4The tool/machine must be maintained in a safe working condition at all times and examined at regular intervals for damage and function by trained
competent personnel. Any dismantling procedure shall be undertaken only by personnel trained in Avdel UK Limited procedures. Do not dismantle this
tool/machine without prior reference to the maintenance instructions. Please contact Avdel UK Limited. with your training requirements.
5The tool/machine shall at all times be operated in accordance with relevant Health and Safety legislation. In the U.K. the “Health and Safety at Work
etc. Act 1974” applies. Any question regarding the correct operation of the tool/machine and operator safety should be directed to Avdel UK Limited.
6The precautions to be observed when using this tool/machine must be explained by the customer to all operators.
7Always disconnect the airline from the tool/machine inlet before attempting to adjust, fit or remove a nose assembly.
8Do not operate a tool/machine that is directed towards any person(s) or the operator.
9Always adopt a firm footing or a stable position before operating the tool/machine.
10 Ensure that vent holes do not become blocked or covered and that hoses are always in good condition.
11 The operating pressure shall not exceed 7 bar (100 lbf/in2).
12 The combination of fastener, mandrel, hole size and sheet thickness shall be in accordance with Avdel UK Limited. Specifications.
13 Do not operate the tool if it is not fitted with a complete nose assembly unless specifically instructed otherwise.
14 When using the tool, the wearing of safety glasses is required both by the operator and others in the vicinity to protect against fastener ejection, should
a fastener be placed ‘in air’. We recommend wearing gloves if there are sharp edges or corners on the application.
15 Take care to avoid entanglement of loose clothes, ties, long hair, cleaning rags etc. in the moving parts of the tool which should be kept dry and clean
for best possible grip.
16 When carrying the tool from place to place keep hands away from the trigger/lever to avoid inadvertent startup.
17 Excessive contact with hydraulic oil should be avoided. To minimize the possibility of rashes, care should be taken to wash thoroughly.
IMPORTANT
While a small amount of wear and marking will naturally occur through normal and correct use of mandrels, they must be regularly
examined for excessive wear and marking, with particular attention to the head diameter, the tail jaw gripping area of the shank
or heavy pitting of the shank and any mandrel distortion. Mandrels which fail during use could forcibly exit the tool. It is the
customer‘s responsibility to ensure that mandrels are replaced before any excessive levels or wear and always before the maximum
recommended number of placings. Contact your Avdel representative who will let you know what that figure is by measuring the
broach load of your application with a calibrated test tool. These tools can also be purchased under Part Number 07900-09080,
supplied with all necessary information for testing in this manual.

5
Specification for 07537 Tool
Tool Dimensions
Specifications
Air Pressure Minimum - Maximum 5-7 bar (70-100 lbf/in2)
Free Air Volume Required @ 5.1 bar /75 lbf/in22.6 litres (0.09 ft3)
Stroke Minimum 28.0 mm (1.10 in)
Pull Force @ 5.5 bar /80 lbf/in23.89 kN (875 lbf)
Cycle time Approximately 1 second
Noise Level Less than 70 dB(A)
Weight Tool 2.3 kg (5.06 lb)
Vibration Less than 2.5 m/s2(8 ft/s2)
07537
475
18.70
338
13.30
51
2
110
120
121
150
60
2.36
98
3.85
163
6.41
140
5.51
50
1.96
07537
Part Number 07537-00200

6
Intent of Use
The pneumatic 07537 tool is a handheld lightweight tool designed to place Avdel®speed fasteners (except 1/16” Avlug®) making it ideal for batch or
flow-line assembly in a wide variety of applications throughout all industries.
Part numbers are shown to order a complete tool but no nose equipment.
The tool part number for the 07537 model is 07537-00200. See the general assemblies on pages 26-27.
The tool will place most repetition fasteners, as shown in the table below.
The tool is used with specific nose equipment. Reference must be made to the Nose Equipment section of the manual when selecting compatible
components for the type and size of fastener used in your application (see pages 12-20). Nose jaw dimensions are shown on page 13.
FASTENER NAME
FASTENER SIZE
3/32" 1/8" 5/32" 3/16" 1/4" 2.5mm
2.8mm 3mm 3.5mm 4mm 6mm
M2.5
4-40
UNC
M3
6-32
UNC
CHOBERT®● ● ● ● ●
GROVIT®● ● ● ●
AVLUG®● ●
BRIV®● ● ● ● ●
RIVSCREW®● ● ● ●
AVTRONIC®●
AVSERT®● ●

7
Air Supply
Putting into Service
All tools are operated with compressed air at an optimum pressure of 5.5 bar. We recommend the use of pressure regulators and filtering systems on
the main air supply. These should be fitted within 3 metres of the tool (see diagram below) to ensure maximum tool life and minimum tool maintenance.
Air supply hoses should have a minimum working effective pressure rating of 150% of the maximum pressure produced in the system or 10 bar,
whichever is the highest. Air hoses should be oil resistant, have an abrasion resistant exterior and should be armoured where operating conditions may
result in hoses being damaged. All air hoses MUST have a minimum bore diameter of 6.4 millimetres or 1/4inch.
Read servicing daily details page 21.
8
6
4
2
0
10
12
14
16
07537
STOP COCK
(USED DURING MAINTENANCE
OF FILTER/REGULATOR UNIT)
TAKE OFF POINT
FROM
MAIN SUPPLY
MAIN SUPPLY
DRAIN POINT
PRESSURE REGULATOR
AND FILTER (DRAIN DAILY)
3 METRES MAXIMUM

8
Mechanical Cursors
Putting into Service
For reference there are three different mechanical cursor types:
•07271-01100 Used for Standard mandrels and 5/32” Disposable mandrels
•07279-05843 Used for 1/8” Disposable mandrels
•07279-05845 Used for 3/16” Disposable mandrels
The difference in the above assemblies is the internal diameter of the End Plug.
These are colour coded see below:
END PLUG
07537




07537

SPRING
LOADED END
CURSOR NOSE
JAWS
TOOL
BARREL
END PLUG
MECHANICAL CURSOR
PART NO.
END PLUG
PART NO. COLOUR HOLE DIAMETER (mm)
07271-01100 07150-00402 PLAIN STEEL 2.7
07279-05843 07159-05844 GOLD 2.2
07279-05845 07159-05846 SILVER 3.3

9
Cursor
Loading and Reloading the Tool
Putting into Service
While the cursor will be fitted the correct way round when the tool is supplied, we recommend that you check its orientation before fitting the nose
equipment. The sprung loaded, slightly concave, end of the cursor should point towards the front of the tool as shown in the illustration.
When fitted the correct way round, the cursor will easily slide out of the barrel when a mandrel is pushed into its centre then pulled back.
To reverse the orientation of the cursor, follow these steps:
Item numbers in bold refer to the general assembly and parts list for the
07537-00200 on pages 26-27.
•Remove the clip 48 and slide off end cap 50.
•Using an Allen Key, remove one cap head screw 5ensuring that any
trapped air is exhausted. remove the second cap head screw 5.
•Pull out rear plug 47.
•Pull out tail jaw piston assembly 51 together with jaws 34.
•Lift out spring 35 and jaw housing 41.
•Insert a mandrel into the hole in the rear end of barrel 44 until it protrudes
through the front of the barrel, then pull out the mandrel and cursor together through the front.
•Reassemble components in reverse order.
•Insert Mechanical Cursor Assembly 36 into the front of the barrel, correct way round.
When ordering a complete tool or system you will normally be supplied with all the nose equipment required for the fastener to be placed. To identify nose
equipment components or to select the correct elements, read the nose equipment section, on pages 12-20.
If you have been supplied with a nose jaw, mandrels and mandrel follower springs proceed with loading the tool and fitting the nose equipment as shown
overleaf.
IMPORTANT
If fitted incorrectly, the cursor will not allow feeding of the fasteners.
IMPORTANT
The procedure for loading the tool and for fitting the nose equipment to the tool is integral.
Item numbers in bold refer to the general assembly and parts list for the 07537-00200 on pages 26-27.
SPRING
LOADED END
CURSOR
NOSE
JAWS
TOOL
BARREL

10
Loading the Tool
Reloading the Tool
Operating Procedure
Putting into Service
•Connect the air supply to the tool.
•Open tail jaws 34 which grip the mandrel, by switching off the tail jaw switch (items 22 and 23).
•Screw selected nose jaws onto barrel 44 of the tool.
•* Insert a mandrel into the tail end of the fasteners through the paper pod.
•Slide the mandrel follower spring onto the mandrel ensuring correct orientation, as shown in the table on page 11.
•Gripping the tail end of the mandrel, tear off the paper pod from around the fasteners.
•Open the nose jaws either by rotating the outer ring on Cam operated jaws or by pushing outwards on the jaw ends, as illustrated below left.
•Insert the previously assembled mandrel, mandrel follower spring and fasteners into the nose jaws until the first fastener to be placed is protruding
from the nose jaw.
•Close the nose jaws and adjust so that the first fastener protrudes by 1.5mm - 3mm (1/16” to 1/8”), as shown in the illustration below right.
•Close the tail jaws to ensure the mandrel is gripped, by switching on the tail jaw switch (items 22 and 23).
•Push the fastener, protruding from the nose jaws, fully into the application holes ensuring that the tool is held square.
•Operate the trigger without releasing - the mandrel head is pulled through the fastener, forming the fastener into the application.
•Remove the tool.
•Release the trigger. The next fastener will be automatically presented through the nose jaws, ready for placing.
•Open tail jaws 34 of tool.
•Open the nose jaws and pull the empty mandrel and mandrel follower spring out of the tool.
•Reload the tool by following the above instructions, starting at stage •*.
IMPORTANT
You must check that the cursor orientation and the nose equipment are correct before attempting to operate the tool.
Item numbers in bold refer to the general assembly and parts list for the 07537-00200 on pages 26-27.
1.5mm - 3mm
(1/16" - 1/8")

11
Putting into Service
MANDREL FOLLOWER SPRINGS IDENTIFICATION AND ORIENTATION
FASTENER NOSE JAW
(SEE NOSE EQUIPMENT SECTION) MANDREL SIZE MANDREL/MANDREL FOLLOWER SPRING AND FASTENER ASSEMBLY
NAME SIZE
BRIV®
3/32" STANDARD TAPERED ALL
MANDREL FOLLOWER SPRING
MANDREL
SPRING
FERRULE
MANDREL HEAD
3/32" LIMITED ACCESS & LIMITED ACCESS
CAM OPERATED ALL
1/8" ALL ALL
5/32" ALL ALL
3/16" ALL ALL
6mm STANDARD ALL EXCEPT 3rd
OVERSIZE
CHOBERT®
AVLUG®
GROVIT®
3/32" ALL EXCEPT STANDARD TAPERED,
LIMITED ACCESS ALL
3/32" STANDARD TAPERED, LIMITED
ACCESS ALL
1/8" ALL ALL
CHOBERT®
GROVIT®
5/32" ALL ALL EXCEPT 3rd
OVERSIZE
5/32" ALL 3rd OVERSIZE
3/16" ALL ALL EXCEPT
2nd OVERSIZE
3/16" ALL 2nd OVERSIZE
CHOBERT® 1/4" ALL ALL
RIVSCREW®
2.8mm
3mm ALL ALL
3.5mm
4mm ALL ALL
AVSERT®
2.5mm
4 × 40
UNC
ALL ALL
3mm
6 × 32
UNC
ALL ALL
AVSERT®
2.5mm ALL ALL
2.8mm ALL EXCEPT LIMITED ACCESS ALL
2.8mm LIMITED ACCESS ALL

12
Nose Jaws
Nose Assemblies
IMPORTANT
To avoid complete dismantling of the tool it is essential to check the orientation of the cursor before fitting the nose equipment
to the tool. See ‘CURSOR’ section on page 9.
It is essential that the correct nose equipment is fitted to the tool to ensure both effective placing of the fastener and SAFE
operation of the tool. READ THE SAFETY INSTRUCTIONS page 4 carefully.
On speed fastening tools such as 0753 MkII type, the nose equipment always consists of three elements: a nose jaw, a mandrel and a mandrel follower
spring. All three items are matched to the fastener being placed and to the hole size in the application.
To identify the correct combination of nose equipment to fit your tool first select a nose jaw by reading the section below then read the mandrel section
to select part numbers both for the mandrel itself and for the mandrel follower spring. Mandrels and mandrel follower springs are illustrated on page 11.
To fit the nose equipment, follow the ‘Loading the Tool’ procedure page 10.
Nose Jaws can be categorised into 7 different basic shapes as illustrated opposite, even though internal dimensions will vary according to the fastener
it is intended for. Exact dimensions referring to the letters in the illustrations opposite are indicated in the ‘Nose Jaw Selection Tables’ on pages 14-15.
For a particular shape, there may be several options of end form giving access benefits or fastener placing enhancement.
Flat
•Normal end form of all nose jaws.
•Suitable on all applications with no access restrictions.
Universal
•Designed for use with universal head Chobert®fasteners.
•Can also be used with Briv®fasteners to obtain the highest possible clench. Note this reduces the maximum grip range of the Briv®fastener by
approximately 0.015” (0.4mm).
Recessed
•For use with Briv®fasteners ONLY.
•It gives a higher clench than a flat end form but less than a universal end form, with no reduction of the grip range of the fastener.
Tapered
•Available as shown in the ‘Nose Jaw Selection Tables’.
•Allows greater accessibility than a flat end form and places the same range.
Head Forming
•For use with Rivscrew®fasteners ONLY.
•Deforms the head of the fastener to achieve good clench.
IMPORTANT
The wrong nose jaw could result in an incorrectly placed fastener or incorrect clench.

13
Selecting a Nose Jaw
Nose Assemblies
Available in 4 different end forms to place
all fasteners (except Rivscrew). Suitable
on applications with no or little access
restriction.
•List the name, size and material of the fastener to be placed.
•Look for this fastener in the first column of the nose jaw selection tables on page 14 if you use
imperial measurements and on page 15 if you use metric units.
•Looking right across the table, take note of which nose jaws are available. ONLY those shown
are available.
•Select which is most suitable for your application by referring to the respective nose jaw
drawing. If your application has no access restriction, you should select the standard shape with
a flat end form with or without a cam.
Available as shown in NOSE JAW
SELECTION TABLE.
Allows access into very restrictive
applications.
Available as shown in NOSE JAW SELECTION TABLE overleaf. Equivalent functions to the Standard and Limited Access above
with the addition of a cam to ease and speed up the nose jaw opening thus the pod reloading procedure.
Available as shown in NOSE JAW
SELECTION TABLE.
Allows more penetration into
applications with restricted access.
Mandrels must be curved by hand to
follow the shape of the jaw.
Available to place most of the fasteners.
Allows more penetration into
applications with no other access
restriction.
Dimensions shown in bold are millimetres. Other dimensions are in inches.
'D'
'E'
'B'
28.6
1.125
33.5
1.32
FLAT UNIVERSAL RECESSED TAPERED
STANDARD
FLAT UNIVERSAL RECESSED
LONG
'D'
'E'
'B'
28.6
1.125
'F'
33.5
1.32
LONG CURVED
RIVET
Ø
'F'
mm in.
1/8.620 15.7
5/32 .690 17.5
3/16 .720 18.3
FLAT RECESSED
'D'
'E'
'B'
20.5
0.81
41.4
1.63
FLAT
LIMITED ACCESS
'D'
'E'
'B'
28.6
1.25
34
1.34
FLAT HEAD FORMING (HF)
STANDARD CAM OPERATED
'D'
'E'
'B'
28.6
1.25
34
1.34
FLAT
LONG CAM OPERATED
'D'
'E'
'B'
28.6
1.25
37.1
1.46
FLAT
LIMITED ACCESS CAM OPERATED

14
Nose Jaw Selection - Imperial
Nose Assemblies
The ‘REF Nş’ column cross references with the ‘REF Nş’ columns in the mandrel section. It identifies both the mandrel and
mandrel follower spring required for a particular nose jaw with a specific fastener.
# These nose jaws are suitable for placing Chobert®rivets with a Universal Head Form. When used on the equivalent size of Briv®, the highest possible
clench is achieved. Note when using Briv®fasteners, the maximum grip is reduced by approximately 0.015“ (0.4mm).
FASTENER REF.
Nº
NOSE JAW
TYPE AND END FORM PART Nº DIMENSIONS
'B' 'D' 'E'
3/32" CHOBERT®
&GROVIT®1STANDARD - FLAT 07150-03003 .36 1.30 .16
1STD. CAM OPERATED - FLAT 07170-04500 .36 1.30 .16
2STANDARD - TAPERED 07170-03103 .36 1.30 .16
4LONG - FLAT 07150-04003 .41 2.30 .16
1/8" CHOBERT®
&GROVIT®5STANDARD - FLAT 07150-03004 .41 1.18 .20
5STANDARD - TAPERED 07170-03104 .41 1.19 .20
6LONG - FLAT 07150-04004 .41 2.18 .20
6LONG CURVED - FLAT 07150-05004 .41 2.12 .20
5/32" CHOBERT®
&GROVIT®7STANDARD - FLAT 07150-03005 .48 1.30 .24
7STANDARD - TAPERED 07150-03105 .44 1.30 .24
8LONG - FLAT 07150-04005 .48 2.30 .24
8LONG CURVED - FLAT 07150-05005 .48 2.23 .24
3/16" CHOBERT®
&GROVIT®9STANDARD - FLAT 07150-03006 .56 1.18 .33
9STANDARD - TAPERED 07150-03106 .56 1.18 .33
10 LONG - FLAT 07150-04006 .56 2.30 .33
10 LONG CURVED - FLAT 07150-05006 .56 2.21 .33
1/4" CHOBERT®11 STANDARD - FLAT 07150-03008 .64 1.18 .39
12 LONG - FLAT 07150-04008 .64 2.18 .39
3/32" BRIV®Brass
only
13 STANDARD - TAPERED 07170-03103 .36 1.30 .15
14 LIMITED ACCESS 07274-01000 .22 1.07 .16
1/8" BRIV®Al. Alloy,
Brass, Steel
15 STANDARD - FLAT 07150-03004 .41 1.18 .20
15 STANDARD - TAPERED 07170-03104 .41 1.19 .20
16 LONG - RECESSED 07170-03204 .41 2.18 .30
16 LONG CURVED - RECESSED 07170-03304 .41 2.12 .30
5/32" BRIV®Al.
Alloy, Brass, Steel
17 STANDARD - FLAT 07150-03005 .48 1.30 .24
18 LONG - FLAT 07150-04005 .48 2.30 .24
18 LONG CURVED - FLAT 07150-05005 .48 2.23 .24
5/32" BRIV®
St.Steel only
19 STANDARD - FLAT 07150-03005 .48 1.30 .24
20 LONG - FLAT 07150-04005 .48 2.30 .24
20 LONG CURVED - FLAT 07150-05005 .48 2.23 .24
3/16" BRIV®Al.
Alloy, Brass, Steel
21 STANDARD - FLAT 07150-03006 .56 1.18 .33
22 LONG - FLAT 07150-04006 .56 2.30 .33
22 LONG CURVED - FLAT 07150-05006 .56 2.21 .33
3/16" BRIV®
St.Steel only
23 STANDARD - FLAT 07150-03006 .56 1.18 .33
24 LONG - FLAT 07150-04006 .56 2.30 .33
24 LONG CURVED - FLAT 07150-05006 .56 2.21 .33
6mm BRIV®Al.
Alloy, Steel
25 STD. CAM OPERATED 07170-05600 .64 1.21 .52
26 LONG CAM OPERATED 07170-05700 .64 2.19 .52
3/32" AVLUG®27 STANDARD - FLAT 07150-03003 .36 1.30 .16
27 STD. CAM OPERATED - FLAT 07170-04500 .36 1.30 .16
28 LONG CURVED - FLAT 07150-05003 .41 2.28 .16
1/8" AVLUG®29 STANDARD - FLAT 07150-03004 .41 1.18 .20
29 STD. CAM OPERATED - FLAT 07170-04600 .41 1.18 .20
30 LONG CURVED - FLAT 07150-05004 .41 2.12 .20
2.5mm. 4-40 UNC
AVSERT®31 STANDARD - FLAT 07150-03003 .36 1.30 .16
3.0mm, 6-32 UNC
AVSERT®32 STANDARD - FLAT 07150-03004 .41 1.18 .20
2.5mm AVTRONIC®33 STANDARD - FLAT 07150-03003 .36 1.30 .16
34 LONG - FLAT 07150-04003 .41 2.30 .16
2.8mm AVTRONIC®35 STANDARD - FLAT 07271-05600 .36 1.30 .16
37 LONG - FLAT 07271-05900 .41 2.30 .16
2.8mm RIVSCREW®38 STD. CAM OPERATED - HF 07271-03000 .41 1.18 .24
3.0mm RIVSCREW®39 STD. CAM OPERATED - HF 07271-03000 .41 1.18 .24
3.5mm RIVSCREW®40 STD. CAM OPERATED - HF 07271-03500 .41 1.18 .24
4.0mm RIVSCREW®41 STD. CAM OPERATED - HF 07271-04000 .41 1.18 .25
REF.
Nº
NOSE JAW
TYPE AND END FORM PART Nº DIMENSIONS
'B' 'D' 'E'
1# STANDARD - UNIVERSAL 07150-03203 .36 1.33 .24
1LTD. ACCESS CAM OPERATED 07177-03003 .20 1.18 .16
3LIMITED ACCESS 07274-01000 .22 1.07 .16
4LONG CURVED - FLAT 07150-05003 .41 2.28 .16
5# STANDARD - UNIVERSAL 07150-03204 .41 1.22 .32
5STD. CAM OPERATED - FLAT 07170-04600 .41 1.18 .20
6# LONG - UNIVERSAL 07150-04204 .41 2.22 .30
6LONG CAM OPERATED - FLAT 07170-05000 .41 2.18 .20
7# STANDARD - UNIVERSAL 07150-03205 .48 1.35 .41
7STD. CAM OPERATED - FLAT 07170-04700 .48 1.30 .24
8# LONG - UNIVERSAL 07150-04205 .48 2.35 .42
8LONG CAM OPERATED - FLAT 07170-05100 .48 2.30 .24
9# STANDARD - UNIVERSAL 07150-03206 .56 1.24 .47
9STD. CAM OPERATED - FLAT 07170-04800 .56 1.18 .33
10 # LONG - UNIVERSAL 07150-04206 .56 2.39 .48
10 LONG CAM OPERATED - FLAT 07170-05200 .56 2.30 .33
11 STD. CAM OPERATED - FLAT 07170-04900 .64 1.18 .39
12 LONG CAM OPERATED - FLAT 07170-05300 .64 2.18 .39
14 LTD. ACCESS CAM OPERATED 07177-03003 .20 1.18 .16
-- - - - -
15 STANDARD - RECESSED 07170-03004 .41 1.20 .30
16 LONG - FLAT 07150-04004 .41 2.18 .20
16 LONG CURVED - FLAT 07150-05004 .41 2.12 .20
-- - - - -
17 STANDARD - RECESSED 07170-03005 .48 1.32 .41
18 LONG - RECESSED 07170-03205 .48 2.30 .41
18 LONG CURVED - RECESSED 07170-03305 .48 2.23 .41
19 STANDARD - RECESSED 07170-03005 .48 1.32 .41
20 LONG - RECESSED 07170-03205 .48 2.30 .41
20 LONG CURVED - RECESSED 07170-03305 .48 2.23 .41
21 STANDARD - RECESSED 07170-03006 .56 1.20 .47
22 LONG - RECESSED 07170-03206 .56 2.30 .47
22 LONG CURVED - RECESSED 07170-03306 .56 2.21 .47
23 STANDARD - RECESSED 07170-03006 .56 1.20 .47
24 LONG - RECESSED 07170-03206 .56 2.30 .47
24 LONG CURVED - RECESSED 07170-03306 .56 2.21 .47
25 STANDARD - FLAT 07170-05800 .64 1.21 .52
26 LONG - FLAT 07170-05900 .64 2.19 .52
27 STANDARD - TAPERED 07150-03103 .36 1.30 .16
28 LONG - FLAT 07150-04003 .41 2.30 .16
- - - - -
29 STANDARD - TAPERED 07170-03104 .41 1.19 .20
30 LONG - FLAT 07150-04004 .41 2.18 .20
30 LONG CAM OPERATED - FLAT 07170-05000 .41 2.18 .20
-- - - - -
32 STD. CAM OPERATED - FLAT 07170-04600 .41 1.18 .20
33 LTD. ACCESS CAM OPERATED 07271-08000 .41 1.18 .16
-
36 LTD. ACCESS CAM OPERATED 07271-08100 .40 1.18 .16
-- - - - -
-- - - - -
-- - - - -
-- - - - -
-- - - - -

15
Nose Jaw Selection - Metric
Nose Assemblies
# These nose jaws are suitable for placing Chobert®rivets with a Universal Head Form. When used on the equivalent size of Briv®, the highest possible
clench is achieved. Note that when using Briv®fasteners, the maximum grip is reduced by approximately 0.015“ (0.4mm).
FASTENER REF.
Nº
NOSE JAW
TYPE AND END FORM PART Nº DIMENSIONS
'B' 'D' 'E'
3/32" CHOBERT®
&GROVIT®
1STANDARD - FLAT 07150-03003 9.14 33.02 4.06
1STD. CAM OPERATED - FLAT 07170-04500 9.14 33.02 4.06
2STANDARD - TAPERED 07170-03103 9.14 33.02 4.06
4LONG - FLAT 07150-04003 10.41 58.42 4.06
1/8" CHOBERT®
&GROVIT®
5STANDARD - FLAT 07150-03004 10.41 29.97 5.08
5STANDARD - TAPERED 07170-03104 10.41 30.23 5.08
6LONG - FLAT 07150-04004 10.41 55.37 5.08
6LONG CURVED - FLAT 07150-05004 10.41 53.85 5.08
5/32" CHOBERT®
&GROVIT®
7STANDARD - FLAT 07150-03005 12.19 33.02 6.10
7STANDARD - TAPERED 07150-03105 11.18 33.02 6.10
8LONG - FLAT 07150-04005 12.19 58.42 6.10
8LONG CURVED - FLAT 07150-05005 12.19 56.64 6.10
3/16" CHOBERT®
&GROVIT®
9STANDARD - FLAT 07150-03006 14.22 29.97 8.38
9STANDARD - TAPERED 07150-03106 14.22 29.97 8.38
10 LONG - FLAT 07150-04006 14.22 58.42 8.38
10 LONG CURVED - FLAT 07150-05006 14.22 56.13 8.38
1/4" CHOBERT®11 STANDARD - FLAT 07150-03008 16.26 29.97 9.91
12 LONG - FLAT 07150-04008 16.26 55.37 9.91
3/32" BRIV®Brass
only
13 STANDARD - TAPERED 07170-03103 9.14 33.02 3.81
14 LIMITED ACCESS 07274-01000 5.59 27.18 4.06
1/8" BRIV®Al.
Alloy, Brass, Steel
15 STANDARD - FLAT 07150-03004 10.41 29.97 5.08
15 STANDARD - TAPERED 07170-03104 10.41 30.23 5.08
16 LONG - RECESSED 07170-03204 10.41 55.37 7.62
16 LONG CURVED - RECESSED 07170-03304 10.41 53.85 7.62
5/32" BRIV®Al.
Alloy, Brass, Steel
17 STANDARD - FLAT 07150-03005 12.19 33.02 6.10
18 LONG - FLAT 07150-04005 12.19 58.42 6.10
18 LONG CURVED - FLAT 07150-05005 12.19 56.64 6.10
5/32" BRIV®
St.Steel only
19 STANDARD - FLAT 07150-03005 12.19 33.02 6.10
20 LONG - FLAT 07150-04005 12.19 58.42 6.10
20 LONG CURVED - FLAT 07150-05005 12.19 56.64 6.10
3/16" BRIV®Al.
Alloy, Brass, Steel
21 STANDARD - FLAT 07150-03006 14.22 29.97 8.38
22 LONG - FLAT 07150-04006 14.22 58.42 8.38
22 LONG CURVED - FLAT 07150-05006 14.22 56.13 8.38
3/16" BRIV®
St.Steel only
23 STANDARD - FLAT 07150-03006 14.22 29.97 8.38
24 LONG - FLAT 07150-04006 14.22 58.42 8.38
24 LONG CURVED - FLAT 07150-05006 14.22 56.13 8.38
6mm BRIV®Al.
Alloy, Steel
25 STD. CAM OPERATED 07170-05600 16.33 30.65 13.14
26 LONG CAM OPERATED 07170-05700 16.33 55.65 13.14
3/32" AVLUG®
27 STANDARD - FLAT 07150-03003 9.14 33.02 4.06
27 STD. CAM OPERATED - FLAT 07170-04500 9.14 33.02 4.06
28 LONG CURVED - FLAT 07150-05003 10.41 57.91 4.06
1/8" AVLUG®
29 STANDARD - FLAT 07150-03004 10.41 29.97 5.08
29 STD. CAM OPERATED - FLAT 07170-04600 10.41 29.97 5.08
30 LONG CURVED - FLAT 07150-05004 10.41 53.85 5.08
2.5mm. 4-40 UNC
AVSERT®31 STANDARD - FLAT 07150-03003 9.14 33.02 4.06
3.0mm, 6-32 UNC
AVSERT®32 STANDARD - FLAT 07150-03004 10.41 29.97 5.08
2.5mm AVTRONIC®33 STANDARD - FLAT 07150-03003 9.14 33.02 4.06
34 LONG - FLAT 07150-04003 10.41 58.42 4.06
2.8mm AVTRONIC®35 STANDARD - FLAT 07271-05600 9.14 33.02 4.06
37 LONG - FLAT 07271-05900 10.41 58.42 4.06
2.8mm RIVSCREW®38 STD. CAM OPERATED - HF 07271-03000 10.41 29.97 6.10
3.0mm RIVSCREW®39 STD. CAM OPERATED - HF 07271-03000 10.41 29.97 6.10
3.5mm RIVSCREW®40 STD. CAM OPERATED - HF 07271-03500 10.41 29.97 6.10
4.0mm RIVSCREW®41 STD. CAM OPERATED - HF 07271-04000 10.41 29.97 6.35
REF.
Nº
NOSE JAW
TYPE AND END FORM PART Nº DIMENSIONS
'B' 'D' 'E'
1# STANDARD - UNIVERSAL 07150-03203 9.14 33.78 6.10
1LTD. ACCESS CAM OPERATED 07177-03003 5.08 29.97 4.06
3LIMITED ACCESS 07274-01000 5.59 27.18 4.06
4LONG CURVED - FLAT 07150-05003 10.41 57.91 4.06
5# STANDARD - UNIVERSAL 07150-03204 10.41 30.99 8.13
5STD. CAM OPERATED - FLAT 07170-04600 10.41 29.97 5.08
6# LONG - UNIVERSAL 07150-04204 10.41 56.39 7.62
6LONG CAM OPERATED - FLAT 07170-05000 10.41 55.37 5.08
7# STANDARD - UNIVERSAL 07150-03205 12.19 34.29 10.41
7STD. CAM OPERATED - FLAT 07170-04700 12.19 33.02 6.10
8# LONG - UNIVERSAL 07150-04205 12.19 59.69 10.67
8LONG CAM OPERATED - FLAT 07170-05100 12.19 58.42 6.10
9# STANDARD - UNIVERSAL 07150-03206 14.22 31.50 11.94
9STD.CAM OPERATED - FLAT 07170-04800 14.22 29.97 8.38
10 # LONG - UNIVERSAL 07150-04206 14.22 60.71 12.19
10 LONG CAM OPERATED - FLAT 07170-05200 14.22 58.42 8.38
11 STD. CAM OPERATED - FLAT 07170-04900 16.26 29.97 9.91
12 LONG CAM OPERATED - FLAT 07170-05300 16.26 55.37 9.91
14 LTD. ACCESS CAM OPERATED 07177-03003 5.08 29.97 4.06
-- - - - -
15 STANDARD - RECESSED 07170-03004 10.41 30.48 7.62
16 LONG - FLAT 07150-04004 10.41 55.37 5.08
16 LONG CURVED - FLAT 07150-05004 10.41 53.85 5.08
-- - - - -
17 STANDARD - RECESSED 07170-03005 12.19 33.53 10.41
18 LONG - RECESSED 07170-03205 12.19 58.42 10.41
18 LONG CURVED - RECESSED 07170-03305 12.19 56.64 10.41
19 STANDARD - RECESSED 07170-03005 12.19 33.53 10.41
20 LONG - RECESSED 07170-03205 12.19 58.42 10.41
20 LONG CURVED - RECESSED 07170-03305 12.19 56.64 10.41
21 STANDARD - RECESSED 07170-03006 14.22 30.48 11.94
22 LONG - RECESSED 07170-03206 14.22 58.42 11.94
22 LONG CURVED - RECESSED 07170-03306 14.22 56.13 11.94
23 STANDARD - RECESSED 07170-03006 14.22 30.48 11.94
24 LONG - RECESSED 07170-03206 14.22 58.42 11.94
24 LONG CURVED - RECESSED 07170-03306 14.22 56.13 11.94
25 STANDARD - FLAT 07170-05800 16.33 30.65 13.14
26 LONG - FLAT 07170-05900 16.33 55.65 13.14
27 STANDARD - TAPERED 07150-03103 9.14 33.02 4.06
28 LONG - FLAT 07150-04003 10.41 58.42 4.06
-- - - - -
29 STANDARD - TAPERED 07170-03104 10.41 30.23 5.08
30 LONG - FLAT 07150-04004 10.41 55.37 5.08
30 LONG CAM OPERATED - FLAT 07170-05000 10.41 55.37 5.08
-- - - - -
32 STD. CAM OPERATED - FLAT 07170-04600 10.41 29.97 5.08
33 LTD. ACCESS CAM OPERATED 07271-08000 10.41 29.97 4.06
-- - - - -
36 LTD. ACCESS CAM OPERATED 07271-08100 10.16 29.97 4.06
-- - - - -
-- - - - -
-- - - - -
-- - - - -
-- - - - -

16
Mandrels and Mandrel Follower Springs
Chobert®and Grovit®- Imperial
Nose Assemblies
Mandrels and mandrel follower springs, illustrated on page 11 need to be selected to suit the fastener type and size as well as the size of the hole in the
application. Use of the wrong mandrel could increase the risk of breakage and the wear of the mandrel head.
Feeding problems could occur if the wrong mandrel follower spring is used.
For mandrel or mandrel follower spring selection, follow instructions on page 18.
IMPORTANT
READ THE SAFETY INSTRUCTIONS page 4 carefully.
While a small amount of wear and marking will naturally occur through normal and correct use of mandrels, they must be regularly
examined for excessive wear and marking, with particular attention to the head diameter, the tail jaw gripping area of the shank
or heavy pitting of the shank and any mandrel distortion. Mandrels which fail during use could forcibly exit the tool. It is the cus-
tomer’s responsibility to ensure that mandrels are replaced before any excessive levels of wear and always before the maximum
recommended number of placings. Contact your Avdel. representative who will let you know what that figure is by measuring the
broach load of your application with our calibrated measuring tool. These tools can also be purchased under part number 07900-
09080, supplied with all necessary information for testing.
# S/R: Short Reach Mandrel. See page 18-19 for explanation.
FASTENER REF.
Nº
HOLE
SIZE
STANDARD MANDREL – GREEN
HEAD
Ø
MANDREL
PART Nº P. MAX # S/R MANDREL PART Nº P MAX.
3/32" CHOBERT®
&GROVIT®
1AS REC. .0725 07150-06003 .166 07150-08003 .071
1- - - - - -
2AS REC. .0725 07150-06003 .166 07150-08003 .071
2- - - - - -
3AS REC. .0725 07150-06003 .166 07150-08003 .071
3- - - - - -
4AS REC. .0725 07150-07003 .166 07150-09003 .071
1/8" CHOBERT®
&GROVIT®
5AS REC. .088 07150-06004 .216 07150-08004 .090
6AS REC. .088 07150-07004 .216 07150-09004 .090
5/32" CHOBERT®
&GROVIT®
7AS REC. .107 07150-06005 .244 07150-08005 .100
7- - - - - -
8AS REC. .107 07150-07005 .244 07150-09005 .100
8- - - - - -
3/16" CHOBERT®
&GROVIT®
9AS REC. .132 07150-06006 .247 07150-08006 .102
9- - - - - -
10 AS REC. .132 07150-07006 .247 07150-09006 .102
10 - - - - - -
1/4" CHOBERT®11 AS REC. .184 07150-06008 .268 07150-08008 .110
12 AS REC. .184 07150-07008 .268 07150-09008 .110
HOLE
SIZE
1ST OVERSIZE MANDREL – YELLOW SPRING PART
Nº
HEAD
Ø
MANDREL
PART Nº P. MAX # S/R MANDREL PART Nº P MAX.
+.0015 .074 07150-06303 .174 - - 07150-06803
+.0035 .076 - - 07150-08103 .078 07150-06803
+.0015 .074 07150-06303 .174 07170-06873
+.0035 .076 - - 07150-08103 .078 07170-06873
+.0015 .074 07150-06303 .174 - - 07170-06903
+.0035 .076 - - 07150-08103 .078 07170-06903
+.0035 .076 - - 07150-09103 .078 07150-07803
+.004 .092 07150-06104 .237 07150-08104 .098 07150-06804
+.004 .092 07150-07104 .237 07150-09104 .098 07150-07804
+.008 .115 07150-06105 .284 07150-08105 .116 07170-06875
- - - - - - -
+.008 .115 07150-07105 .284 07150-09105 .116 07170-07875
- - - - - - -
+.014 .146 07150-06106 .320 07150-08106 .130 07170-06876
- - - - - - -
+.014 .146 07150-07106 .320 07150-09106 .130 07170-07876
- - - - - - -
+.012 .196 07150-06108 .330 07150-08108 .134 07150-06808
+.012 .196 07150-07108 .330 07150-09108 .134 07150-07808
FASTENER REF. Nº HOLE
SIZE
2ND OVERSIZE MANDREL - BLUE
HEAD
Ø
MANDREL
PART Nº P. MAX # S/R MANDREL PART Nº P MAX.
3/32" CHOBERT®
&GROVIT®
1+ .0035 .076 07150-06103 .185 - -
1- - - - - -
2+ .0035 .076 07150-06103 .185
2- - - - - -
3+ .0035 .076 07150-06103 .185 - -
3- - - - - -
4+ .0035 .076 07150-07103 .185 - -
1/8" CHOBERT®
&GROVIT®
5+ .010 .098 07150-06204 .268 07150-08204 .110
6+ .010 .098 07150-07204 .268 07150-09204 .110
5/32" CHOBERT®
&GROVIT®
7+ .015 .122 07150-06205 .320 07150-08205 .130
7- - - - - -
8+ .015 .122 07150-07205 .320 07150-09205 .130
8- - - - - -
3/16" CHOBERT®
&GROVIT®
9- - - - - -
9+ .024 .156 07150-06206 .372 07150-08206 .150
10 - - - - - -
10 + .024 .156 07150-07206 .372 07150-09206 .150
1/4" CHOBERT®11 - - - - - -
12 - - - - - -
HOLE
SIZE
3RD OVERSIZE MANDREL – RED SPRING PART
Nº
HEAD
Ø
MANDREL
PART Nº P. MAX # S/R MANDREL PART Nº P MAX.
- - - - - - 07150-06803
- - - - - - -
07170-06873
- - - - - - -
- - - - - - 07170-06903
- - - - - - -
- - - - - - 07150-07803
+.014 .102 07150-06304 .288 07150-08304 .118 07150-06804
+.014 .102 07150-07304 .288 07150-09304 .118 07150-07804
- - - - - - 07170-06875
+.025 .132 07150-06305 .372 07150-08305 .150 07150-06805
- - - - - - 07170-07875
+.025 .132 07150-07305 .372 07150-09305 .150 07150-07805
- - - - - - -
- - - - - - 07150-06806
- - - - - - -
- - - - - - 07150-07806
- - - - - - -
- - - - - - -

17
Chobert®and Grovit®- Metric
Nose Assemblies
Tables below left and right and over the next four pages list part numbers of all mandrels and mandrel follower springs available per fastener or group of
fasteners, i.e. for Chobert®and Grovit®on these pages.
While fastener sizes are always shown in their specified units, each table has been produced twice to offer dimensions in imperial units on the left-hand
page then in metric units on the right-hand page. These ‚Mandrel Selection‘ tables cross-reference with the ‚Nose Jaw Selection‘ tables on pages 14-15
through the ‘Ref. Nş’ column.
It is the diameter of the head at the end of a mandrel which when pulled through controls the expansion of the fastener body.
While there are different head shapes to suit different types of fasteners (see illustration on page 19), progressive head sizes are needed to reflect
manufacturing tolerances on the diameter of the hole in your application so that the fastener always expands sufficiently to fill the hole.
Too large a mandrel head would overstress the mandrel and mandrels which fail during use could forcibly exit the tool.
Selection tables are arranged into four ‚mandrel size‘ sections, ranging from ‚standard’ to ‚3rd oversize‘, each being colour coded as per the end of the
mandrel heads themselves.
# S/R: Short Reach Mandrel. See page 18-19 for explanation.
FASTENER REF.
Nº
HOLE
SIZE
STANDARD MANDREL - GREEN
HEAD
Ø
MANDREL
PART Nº P. MAX # S/R MANDREL PART Nº P MAX.
3/32” CHOBERT®
&GROVIT®
1AS REC. 1.84 07150-06003 4.22 07150-08003 1.80
1- - - - - -
2AS REC. 1.84 07150-06003 4.22 07150-08003 1.80
2- - - - - -
3AS REC. 1.84 07150-06003 4.22 07150-08003 1.80
3- - - - - -
4AS REC. 1.84 07150-07003 4.22 07150-09003 1.80
1/8” CHOBERT®
&GROVIT®
5AS REC. 2.24 07150-06004 5.49 07150-08004 2.29
6AS REC. 2.24 07150-07004 5.49 07150-09004 2.29
5/32” CHOBERT®
&GROVIT®
7AS REC. 2.72 07150-06005 6.20 07150-08005 2.54
7- - - - - -
8AS REC. 2.72 07150-07005 6.20 07150-09005 2.54
8- - - - - -
3/16” CHOBERT®
&GROVIT®
9AS REC. 3.35 07150-06006 6.27 07150-08006 2.59
9- - - - - -
10 AS REC. 3.35 07150-07006 6.27 07150-09006 2.59
10 - - - - - -
1/4" CHOBERT®11 AS REC. 4.67 07150-06008 6.81 07150-08008 2.79
12 AS REC. 4.67 07150-07008 6.81 07150-09008 2.79
HOLE
SIZE
1ST OVERSIZE MANDREL - YELLOW SPRING PART
Nº
HEAD
Ø
MANDREL
PART Nº P. MAX # S/R MANDREL PART Nº P MAX.
+.04 1.88 07150-06303 4.42 - - 07150-06803
+.09 1.93 - - 07150-08103 1.98 07150-06803
+.04 1.88 07150-06303 4.42 - - 07170-06873
+.09 1.93 - - 07150-08103 1.98 07170-06873
+.04 1.88 07150-06303 4.42 - - 07170-06903
+.09 1.93 - - 07150-08103 1.98 07170-06903
+.09 1.93 - - 07150-09103 1.98 07150-07803
+.10 2.34 07150-06104 6.02 07150-08104 2.49 07150-06804
+.10 2.34 07150-07104 6.02 07150-09104 2.49 07150-07804
+.20 2.92 07150-06105 7.21 07150-08105 2.95 07170-06875
- - - - - - -
+.20 2.92 07150-07105 7.21 07150-09105 2.95 07170-07875
- - - - - - -
+.35 3.71 07150-06106 8.13 07150-08106 3.30 07170-06876
- - - - - - -
+.35 3.71 07150-07106 8.13 07150-09106 3.30 07170-07876
- - - - - - -
+.30 4.98 07150-06108 8.38 07150-08108 3.40 07150-06808
+.30 4.98 07150-07108 8.38 07150-09108 3.40 07150-07808
FASTENER REF.
Nº
HOLE
SIZE
2ND OVERSIZE MANDREL - BLUE
HEAD
Ø
MANDREL
PART Nº P. MAX # S/R MANDREL PART Nº P MAX.
3/32” CHOBERT®
&GROVIT®
1+.09 1.93 07150-06103 4.70 - -
1- - - - - -
2+.09 1.93 07150-06103 4.70 - -
2- - - - - -
3+.09 1.93 07150-06103 4.70 - -
3- - - - - -
4+.09 1.93 07150-07103 4.70 - -
1/8” CHOBERT®
&GROVIT®
5+.25 2.49 07150-06204 6.81 07150-08204 2.79
6+.25 2.49 07150-07204 6.81 07150-09204 2.79
5/32” CHOBERT®
&GROVIT®
7+.38 3.10 07150-06205 8.13 07150-08205 3.30
7- - - - - -
8+.38 3.10 07150-07205 8.13 07150-09205 3.30
8- - - - - -
3/16” CHOBERT®
&GROVIT®
9- - - - - -
9+.60 3.96 07150-06206 9.45 07150-08206 3.81
10 - - - - - -
10 +.60 3.96 07150-07206 9.45 07150-09206 3.81
1/4” CHOBERT®11 - - - - - -
12 - - - - - -
HOLE
SIZE
3RD OVERSIZE MANDREL - RED SPRING PART
Nº
HEAD
Ø
MANDREL
PART Nº P. MAX # S/R MANDREL PART Nº P MAX.
- - - - - - 07150-06803
- - - - - - -
- - - - - - 07170-06873
- - - - - - -
- - - - - - 07170-06903
- - - - - - -
- - - - - - 07150-07803
+.35 2.59 07150-06304 7.32 07150-08304 3.00 07150-06804
+.35 2.59 07150-07304 7.32 07150-09304 3.00 07150-07804
- - - - - - 07170-06875
+.63 3.35 07150-06305 9.45 07150-08305 3.81 07150-06805
- - - - - - 07170-07875
+.63 3.35 07150-07305 9.45 07150-09305 3.81 07150-07805
- - - - - - -
- - - - - - 07150-06806
- - - - - - -
- - - - - - 07150-07806
- - - - - - -
- - - - - - -

18
Briv®- Imperial
Nose Assemblies
For mandrel or mandrel follower spring selection, follow instructions above.
To find the correct part number of a mandrel for a particular application, read the instructions below after you have gathered the following information as per
example alongside. Answers for the example are shown in grey italic.
FASTENER NAME example Chobert®
FASTENER SIZE 1/8”
DATASHEET Series 1125
APPLICATION HOLE SIZE 0.1335”
CLEARANCE BEHIND APPLICATION Infinite
‘REF.Nş’ FROM NOSE JAW SELECTION TABLE 5 (standard flat)
•Subtract the minimum hole size recommended (AS REC.) in the fastener datasheet from the actual application hole size. -example: 0.005.
•Turn to the page with the ‘Mandrel Selection’ table for your fastener, selecting either the imperial or the metric dimensions table (pages 16-20).
-example: page 16.
•Staring with the ‘Standard Mandrel - Green’ section, find your fastener size in the left-hand column. -example 1/8” Chobert®& Grovit®.
•If you selected a nose jaw which place you fastener, you should now be able to find a line within your fastener section with the same ‘Ref No.’ as that
from the ‘Nose Jaw Selection’ table. -example: 5. This is your line ‘Ref. No.’ in which you will find both your mandrel and mandrel follower spring part
number. This line continues into the second half of the table for the ‘2nd’ and ‘3rd’ oversize mandrels.
•Scan along the line to the ‘hole size’ columns and select which ever is the nearest or equal to the figure calculated in step one. You may now read the
mandrel part number next to the ‘hole size’. -example: 07150-06104
•For Chobert®and Grovit®only, most mandrels are also available in a ‘short reach’ version (see illustration on page 19). Short reach mandrels are used
to minimise the possibility of the mandrel head contacting an obstruction. This would result in the underside of the fastener head not seating properly on
the application surface, causing a lack on clench in the joint.
•Whichever size mandrel you settle on, you will also need to check the ‘P’ figure against that mandrel is adequate. ‘P’ is the clearance required for the
mandrel head at the back of the application IN ADDITION to the length of the fastener protruding through the application, as shown in the illustration on
page 19.
•You may now read the corresponding mandrel follower spring part number in the right-hand column of the table. -example: 07150-06804.
In all cases, satisfactory clenching of the joint should be assessed particularly if the size of the hole in your application is very close to the next oversize hole
condition, when it will be safe to select the greater size of mandrel to obtain a higher clench. REMEMBER that this will increase the broach load and reduce
the mandrel life.
FASTENER REF.
Nº
HOLE
SIZE
STANDARD MANDREL - GREEN HOLE
SIZE
HEAD Ø MANDREL PART Nº P MAX.
3/32” BRIV®
Brass only
13 AS REC. .072 07150-06013 .119 +.004
14 AS REC. .072 07150-06013 .119 +.004
1/8” BRIV®Al.
Alloy, Brass, Steel
15 AS REC. .092 07271-06414 .120 +.005
16 AS REC. .092 07271-07414 .120 +.005
5/32” BRIV®Al.
Alloy, Brass, Steel
17 AS REC. .110 07150-06015 .136 +.005
18 AS REC. .110 07150-07015 .136 +.005
5/32” BRIV®
St.Steel only
19 AS REC. .120 07170-06805 .126 +.005
20 AS REC. .120 07170-07805 .126 +.005
3/16” BRIV®Al.
Alloy, Brass, Steel
21 AS REC. .141 07150-06016 .157 +.005
22 AS REC. .141 07150-07016 .157 +.005
3/16” BRIV®
St.Steel only
23 AS REC. .150 07170-06806 .150 +.005
24 AS REC. .150 07170-07806 .150 +.005
6mm BRIV®Al.
Alloy, Steel
25 AS REC .179 07150-06018 .165 +.005
26 AS REC .179 07150-07018 .165 +.005
1ST OVERSIZE MANDREL - YELLOW SPRING PART Nº
HEAD Ø MANDREL PART Nº P MAX.
.076 07150-06113 .123 07170-06873
.076 07150-06113 .123 07170-06903
.097 07271-06514 .126 07150-06814
.097 07271-07514 .126 07150-07814
.115 07150-06115 .142 07170-06875
.115 07150-07115 .142 07170-07875
.124 07170-06825 .132 07170-06875
.124 07170-07825 .132 07170-07875
.146 07150-06116 .164 07170-06876
.146 07150-07116 .164 07170-07876
.1535 07170-06826 .156 07170-06876
.1535 07170-07826 .156 07170-07876
.183 07150-06118 .171 07150-06846
.183 07150-07118 .171 07150-07846
FASTENER REF.
Nº
HOLE
SIZE
2ND OVERSIZE MANDREL - BLUE
HEAD Ø MANDREL PART Nº P MAX.
3/32” BRIV®
Brass only
13 +.008 .079 07150-06213 .126
14 +.008 .079 07150-06213 .126
1/8” BRIV®Al.
Alloy, Brass, Steel
15 +.010 .102 07271-06614 .133
16 +.010 .102 07271-07614 .133
5/32” BRIV®Al.
Alloy, Brass, Steel
17 +.010 .120 07150-06215 .149
18 +.010 .120 07150-07215 .149
5/32” BRIV®
St.Steel only
19 - - - -
20 - - - -
3/16” BRIV®Al.
Alloy, Brass, Steel
21 +.010 .151 07150-06216 .170
22 +.010 .151 07150-07216 .170
3/16” BRIV®
St.Steel only
23 - - - -
24 - - - -
6mm BRIV®Al.
Alloy, Steel
25 +.010 .189 07150-06218 .177
26 +.010 .189 07150-07218 .177
HOLE
SIZE
3RD OVERSIZE MANDREL - RED SPRING PART Nº
HEAD Ø MANDREL PART Nº P MAX.
- - - - 07170-06873
- - - - 07170-06903
- - - - 07150-06814
- - - - 07150-07814
- - - - 07170-06875
- - - - 07170-07875
- - - - -
- - - - -
+.012 .153 07150-06316 .173 07170-06876
+.012 .153 07150-07316 .173 07170-07876
- - - - -
- - - - -
- - - - 07150-06846
- - - - 07150-07846

19
Mandrel Head Types and ‘P’ Length
Briv®- Metric
Nose Assemblies
Mandrels for stainless steel Briv®are easily identifiable by a ‘V’ cut in the end of the mandrel heads.
When using curved nose jaws, mandrels have to be bent by hand to match the curvature of the nose jaw, thus ensuring good feed of fasteners.
PP
P P
P
P
AVLUG®
CHOBERT®, GROVIT®,
AVSERT®, AVTRONIC®
BRIV®
RIVSCREW®
SHORT REACH
(CHOBERT®&
GROVIT®ONLY)
BRIV®
(STAINLESS STEEL)
FASTENER REF.
Nº
HOLE
SIZE
STANDARD MANDREL - GREEN
HEAD Ø MANDREL PART Nº P MAX.
2.4mm BRIV®
Brass only
13 AS REC. 1.83 07150-06013 3.02
14 AS REC. 1.83 07150-06013 3.02
3.2mm BRIV® Al.
Alloy, Brass, Steel
15 AS REC. 2.34 07271-06414 3.05
16 AS REC. 2.34 07271-07414 3.05
4.0mm BRIV® Al.
Alloy, Brass, Steel
17 AS REC. 2.79 07150-06015 3.45
18 AS REC. 2.79 07150-07015 3.45
4.0mm BRIV®
St.Steel only
19 AS REC. 3.05 07170-06805 3.20
20 AS REC. 3.05 07170-07805 3.20
4.8mm BRIV® Al.
Alloy, Brass, Steel
21 AS REC. 3.58 07150-06016 3.99
22 AS REC. 3.58 07150-07016 3.99
4.8mm BRIV®
St.Steel only
23 AS REC. 3.81 07170-06806 3.81
24 AS REC. 3.81 07170-07806 3.81
6mm BRIV® Al.
Alloy, Steel
25 AS REC 4.54 07150-06018 4.18
26 AS REC 4.54 07150-07018 4.18
HOLE
SIZE
1ST OVERSIZE MANDREL – YELLOW SPRING PART Nº
HEAD Ø MANDREL PART Nº P MAX.
+.10 1.93 07150-06113 3.12 07170-06873
+.10 1.93 07150-06113 3.12 07170-06903
+.13 2.46 07271-06514 3.20 07150-06814
+.13 2.46 07271-07514 3.20 07150-07814
+.13 2.92 07150-06115 3.61 07170-06875
+ .13 2.92 07150-07115 3.61 07170-07875
+ .13 3.15 07170-06825 3.35 07170-06875
+ .13 3.15 07170-07825 3.35 07170-07875
+.13 3.71 07150-06116 4.17 07170-06876
+.13 3.71 07150-07116 4.17 07170-07876
+ .13 3.90 07170-06826 3.96 07170-06876
+ .13 3.90 07170-07826 3.96 07170-07876
+.13 4.65 07150-06118 4.34 07150-06846
+.13 4.65 07150-07118 4.34 07150-07846
FASTENER REF.
Nº
HOLE
SIZE
2ND OVERSIZE MANDREL - BLUE
HEAD
ØMANDREL PART Nº P MAX.
2.4mm BRIV®
Brass only
13 +.20 2.01 07150-06213 3.20
14 +.20 2.01 07150-06213 3.20
3.2mm BRIV® Al.
Alloy, Brass, Steel
15 +.25 2.59 07271-06614 3.38
16 +.25 2.59 07271-07614 3.38
4.0mm BRIV® Al.
Alloy, Brass, Steel
17 +.25 3.05 07150-06215 3.78
18 +.25 3.05 07150-07215 3.78
4.0mm BRIV®
St.Steel only
19 - - - -
20 - - - -
4.8mm BRIV® Al.
Alloy, Brass, Steel
21 +.25 3.84 07150-06216 4.32
22 +.25 3.84 07150-07216 4.32
4.8mm BRIV®
St.Steel only
23 - - - -
24 - - - -
6mm BRIV® Al.
Alloy, Steel
25 +.25 4.79 07150-06218 4.49
26 +.25 4.79 07150-07218 4.49
HOLE
SIZE
3RD OVERSIZE MANDREL – RED
SPRING PART Nº
HEAD
ØMANDREL PART Nº P MAX.
- - - - 07170-06873
- - - - 07170-06903
- - - - 07150-06814
- - - - 07150-07814
- - - - 07170-06875
- - - - 07170-07875
- - - - -
- - - - -
+.30 3.85 07150-06316 4.39 07170-06876
+.30 3.85 07150-07316 4.39 07170-07876
- - - - -
- - - - -
- - - - 07150-06846
- - - - 07150-07846

20
Avlug®, Avsert®, Avtronic®and Rivscrew®- Imperial and Metric
Nose Assemblies
For mandrel or mandrel follower spring selection, follow instructions on page 18.
HOLE SIZE 1ST OVERSIZE MANDREL - YELLOW SPRING PART Nº
HEAD Ø MANDREL PART Nº P MAX.
+.005 .081 07150-06703 .478 07150-06803
+.003 .079 07150-07703 .368 07150-07803
- - - - 07150-06804
- - - - 07150-07804
- - - - 07150-06803
- - - - 07150-06804
+ .003 .073 07170-06125 .140 07150-06803
+ .003 .073 07170-07125 .140 07150-07803
+ .003 .082 07170-06128 .150 07170-06528
+ .003 .082 07170-06128 .150 07170-06873
+ .003 .082 07170-07128 .150 07170-07528
- - - - 07271-06630
- - - - 07271-06630
- - - - 07271-06635
- - - - 07271-06640
FASTENER REF. Nº HOLE SIZE STANDARD MANDREL – GREEN
HEAD Ø MANDREL PART Nº P MAX.
3/32” AVLUG® 27 AS REC. .076 07150-06603 .353
28 AS REC. .076 07150-07603 .353
1/8” AVLUG® 29 AS REC. .098 07150-06604 .593
30 AS REC. .098 07150-07604 .593
2.5mm. 4-40 UNC
AVSERT® 31 AS REC. .0725 07150-06003 .145
3.0mm. 6-32 UNC
AVSERT® 32 AS REC. .088 07150-06004 .185
2.5mm AVTRONIC® 33 AS REC. .070 07170-06025 .140
34 AS REC. .070 07170-07025 .140
2.8mm AVTRONIC®
35 AS REC. .079 07170-06028 .150
36 AS REC. .079 07170-06028 .150
37 AS REC. .079 07170-07028 .150
2.8mm RIVSCREW® 38 AS REC. * .065 07271-06030 .127
3.0mm RIVSCREW® 39 AS REC. * .065 07271-06030 .127
3.5mm RIVSCREW® 40 AS REC. * .0825 07271-06035 .132
4.0mm RIVSCREW® 41 AS REC. * .103 07271-06140 .150
* These Dimensions are Across Flats
FASTENER REF. Nº HOLE SIZE 2ND OVERSIZE MANDREL - BLUE
HEAD Ø MANDREL PART Nº P MAX.
3/32” AVLUG® 27 - - - -
28 - - - -
1/8” AVLUG® 29 - - - -
30 - - - -
2.5mm. 4-40 UNC
AVSERT®
31 - - - -
3.0mm, 6-32 UNC
AVSERT®
32 - - - -
2.5mm AVTRONIC® 33 + .006 .076 07170-06225 .140
34 +.006 .076 07170-07225 .140
2.8mm AVTRONIC® 35 +.006 .085 07170-06228 .150
36 +.006 .085 07170-06228 .150
37 +.006 .085 07170-07228 .150
2.8mm RIVSCREW® 38 - - - -
3.0mm RIVSCREW® 39 - - - -
3.5mm RIVSCREW® 40 - - - -
4.0mm RIVSCREW® 41 - - - -
HOLE SIZE 3RD OVERSIZE MANDREL - RED SPRING PART Nº
HEAD Ø MANDREL PART Nº P MAX.
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - 07150-06803
- - - - 07150-07803
- - - - 07170-06528
- - - - 07170-06873
- - - - 07170-07528
- - - - -
- - - - -
- - - - -
- - - - -
FASTENER REF. Nº HOLE SIZE STANDARD MANDREL - GREEN
HEAD Ø MANDREL PART Nº P MAX.
3/32” AVLUG® 27 AS REC. 1.93 07150-06603 8.97
28 AS REC. 1.93 07150-07603 8.97
1/8” AVLUG® 29 AS REC. 2.49 07150-06604 15.06
30 AS REC. 2.49 07150-07604 15.06
2.5mm, 4-40 UNC
AVSERT® 31 AS REC. 1.84 07150-06003 3.68
3.0mm, 6-32 UNC
AVSERT® 32 AS REC. 2.24 07150-06004 4.70
2.5mm AVTRONIC® 33 AS REC. 1.78 07170-06025 3.56
34 AS REC. 1.78 07170-07025 3.56
2.8mm AVTRONIC®
35 AS REC. 2.01 07170-06028 3.81
36 AS REC. 2.01 07170-06028 3.81
37 AS REC. 2.01 07170-07028 3.81
2.8mm RIVSCREW® 38 AS REC * 1.65 07271-06030 3.23
3.0mm RIVSCREW® 39 AS REC. * 1.65 07271-06030 3.23
3.5mm RIVSCREW® 40 AS REC. * 2.10 07271-06035 3.35
4.0mm RIVSCREW® 41 AS REC. * 2.62 07271-06140 3.81
* These Dimensions are Across Flats
HOLE SIZE ST OVERSIZE MANDREL - YELLOW SPRING PART Nº
HEAD Ø MANDREL PART Nº P MAX.
+.10 2.06 07150-06703 12.14 07150-06803
+.10 2.01 07150-07703 9.35 07150-07803
- - - - 07150-06804
- - - - 07150-07804
- - - - 07150-06803
- - - - 07150-06804
+.07 1.85 07170-06125 3.56 07150-06803
+.07 1.85 07170-07125 3.56 07150-07803
+.07 2.08 07170-06128 3.81 07170-06528
+.07 2.08 07170-06128 3.81 07170-06873
+.07 2.08 07170-07128 3.81 07170-07528
- - - - 07271-06630
- - - - 07271-06630
- - - - 07271-06635
- - - - 07271-06640
FASTENER REF. Nº HOLE SIZE 2ND OVERSIZE MANDREL - BLUE
HEAD Ø MANDREL PART Nº P MAX.
3/32” AVLUG® 27 - - - -
28 - - - -
1/8” AVLUG® 29 - - - -
30 - - - -
2.5mm, 4-40 UNC
AVSERT® 31 - - - -
3.0mm, 6-32 UNC
AVSERT® 32 - - - -
2.5mm AVTRONIC® 33 +.15 1.93 07170-06225 3.56
34 +.15 1.93 07170-07225 3.56
2.8mm AVTRONIC®
35 +.15 2.16 07170-06228 3.81
36 +.15 2.16 07170-06228 3.81
37 +.15 2.16 07170-07228 3.81
2.8mm RIVSCREW® 38 - - - -
3.0mm RIVSCREW® 39 - - - -
3.5mm RIVSCREW® 40 - - - -
4.0mm RIVSCREW® 41 - - - -
HOLE SIZE 3RD OVERSIZE MANDREL - RED SPRING PART Nº
HEAD Ø MANDREL PART Nº P MAX.
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - 07150-06803
- - - - 07150-07803
- - - - 07170-06528
- - - - 07170-06873
- - - - 07170-07528
- - - - -
- - - - -
- - - - -
- - - - -