Stanley NB08PT-18 User manual

1
NB08PT-18 Blind nut tool
Battery Power Tool
Accessories
Manual

2
©2021 Stanley Black & Decker
All rights reserved.
The information provided may not be reproduced and/or made public in any way and through any means (electronically or mechanically) without
prior explicit and written permission from STANLEY Engineered Fastening. The information provided is based on the data known at the moment of
the introduction of this product. STANLEY Engineered Fastening pursues a policy of continuous product improvement and therefore the products
may be subject to change. The information provided is applicable to the product as delivered by STANLEY Engineered Fastening. Therefore, STANLEY
Engineered Fastening cannot be held liable for any damage resulting from deviations from the original specifications of the product.
The information available has been composed with the utmost care. However, STANLEY Engineered Fastening will not accept any liability with
respect to any faults in the information nor for the consequences thereof. STANLEY Engineered Fastening will not accept any liability for damage
resulting from activities carried out by third parties. The working names, trade names, registered trademarks, etc. used by STANLEY Engineered
Fastening should not be considered as being free, pursuant to the legislation with respect to the protection of trademarks.
OriginalInstruction

3
STANLEY Engineered Fastening policy is one of continuous product development and improvement
and we reserve the right to change the specification of any product without prior notice.
Nose Assemblies
Nose equipment varies according to the blind insert nut type being installed. Each nose assembly
represents a unique set of components which can be ordered individually. Component numbers
refer to the illustration below. We recommend maintaining some stock of spares as items will need
regular replacement if worn. Read the Service Manual for nose assembly instructions.
D
E
B
C
A
A
F
B
C
D
G
I
K
A
H
J
T
K
J

4
MAIN COMPONENTS LIST
A
Mandrel
G
Spin Pull Head Case
B
Nosepiece
H
Spin Pull Head
C
Lock Nut
I
FR Lever
D
Nose Housing
J
Mast Housing
E
Nose Housing Nut
K
Nut
F
Mandrel Lock
*for complete tool explosion and Bill of Material please see service manual
ACCESSORIES CHANGING INSTRUCTIONS
Always wear approved hearing and eye protections at all times when using installation
equipment.
WARNING: Before adjusting tool, always remove the battery pack.
Mounting the mandrel and nosepiece
•Select the correct mandrel (A) and nosepiece (B) for the blind nut (K) to be
installed.
•Loosen the nose housing nut (E), Remove the nose housing (D).
•Press the mandrel lock (F), Loosen and remove the mandrel (A).
•Screw the correct mandrel (A) into Spin Pull Head (H) while pressing the mandrel
lock (F). Lock the mandrel (A)
•Loosen the lock nut (C) and unscrew and remove the nosepiece (B) and Lock nut
(C)
•Screw the Lock nut (C) onto the correct nosepiece (B) and screw the nosepiece (B)
into the nose housing (D) lightly.
•Adjust the position of the nosepiece (B) according to the blind nut (K) to be
installed. The length of mandrel protruding from the top of blind nut (K) to be 0-
0.5mm.
•Tighten the lock nut (C) by a spanner properly.

5
PLACING SPECIFICATIONS
Nut Type
PLACING CAPACITY
NB08PT-18
M3
M4
M5
M6
M8
M10
Eurosert®
●
●
●
●
●
●
Thin Sheet Nutsert®
●
●
●
●
●
●
DK/DL
●
●
●
●
●
●
Euro Hexsert®/Hexsert®
●
●
●
●
●
●
High Strength Hexsert®
●
●
Squaresert®
●
●
●
Standard Nut (Steel)
●
●
●
●
●
●
Standard Nut (Aluminum)
●
●
●
●
●
●
Standard Nut (Stainless
steel)
●
●
●
●
●
Closed End Nut
●
●
●
●
●
Hexagonal Nut
●
●
●
●
●
●
All Hexagonal Nut
●
Tetra Nut
●
●
●
●
Knurled Nut
●
●
●
●
Soft Set Nut
●
●
●
Slit Nut
●
Pipe Nut
●
HB Bolt
●
HB Bolt for round pipe
●
Note:
Force control can be used for the following sizes only.
Aluminum M6 or more (Except for Slit Nut).
Steel M5 or more.
Stainless steel M5 or more.

6
MANDREL AND NOSEPIECE
WARNING: When selecting mandrel and nosepiece, always use the compatible parts. Using different
parts may cause nut tightening failure or tool failure.
Note:
1. Refer Table B for Thin sheet Nutsert®.
2. Refer Table C for Thin head Hexsert®.
Table A Mandrel and Nosepiece compatible chart *：Option parts
Nut Size
MANDREL
NOSEPIECE
Part No.
O.D
Part No
I.D
M3
PNT600-01-3*
φ3
PNT600-02-3*
φ4.0
M4
PNT600-01-4
φ4
PNT600-02-4
φ4.5
M5
PNT600-01-5P
φ5
PNT600-02-5
φ5.1
M6
PNT600-01-6P
φ6
PNT600-02-6
φ6.1
M8
PNT600-01-8M
φ8
PNT600-02-8
φ8.1
M10
PNT600-01-10A*
φ10
PNT600-02-10*
φ10.1
6-32 UNC
PNT600-01-632*
φ3.5
PNT600-02-632*
φ3.6
8-32 UNC
PNT600-01-832*
Φ4.1
PNT600-02-832*
Φ4.3
10-24 UNC
PNT600-01-1024*
Φ4.8
PNT600-02-5
φ5.1
10-32 UNF
PNT600-01-1032*
Φ4.8
PNT600-02-5
φ5.1
Table B Thin sheet Nutsert® compatible chart *：Option parts
Nut Size
MANDREL
NOSEPIECE
Part No.
O.D
Part No
I.D
M3
PNT600-01-3*
φ3
TNM00146*
φ3.1
M4
PNT600-01-4P*
φ4
TNM00147*
φ4.1
M5
PNT600-01-5P
φ5
TNM00148*
φ5.1
M6
PNT600-01-6P
φ6
TNM00149*
φ6.1
M8
PNT600-01-8P*
φ8
TNM00150*
φ8.1
Inside Diameter
Outside Diameter
M8×1.0
Inside Diameter
Outside Diameter
M8×1.0

7
Table C Thin head Hexsert® compatible chart *：Option parts
Nut Size
MANDREL
NOSEPIECE
Part No.
O.D
Part No
I.D
M4
PNT600-01-4P*
φ4
TNM00151*
φ4.1
M5
PNT600-01-5P
φ5
TNM00152*
φ5.1
M6
PNT600-01-6P
φ6
TNM00153*
φ6.1
M8
PNT600-01-8P*
φ8
TNM00150*
φ8.1
MANDREL AND NOSEPIECE (OPTIONS)
1. Pipe Nut (Made to order)
When fastening the pipe nut SRH-630-191-K2, install the nose assembly for the pipe
nut. The mandrel used is PNT600-01-6P. Please refer to the following list for the
nose assembly components for pipe nuts.
●SRH-630-191-K2
Nose Assembly
TNM00354
SA Mast Housing
TNM00355
SA Nose Housing
TNM00356
Nose Housing
TNM00257
Nose Slider
PNT600-137A
Slider Spring
AN600P-31
Retaining Ring
AN600P-32
Nosepiece
PNT600-02-6NP
Lock Nut
PNT600-03
Hexagon socket button bolt
PNT600-100
Spacer
PNT600-138
Outside Diameter
M8×1.0
Inside Diameter
Lock Nut
Slider Spring
Nosepiece
Retaining Ring
Nose Slicer
Nose Housing
SA Mast Housing
Spacer
Button Head Cap Screw

8
2. Pipe HB Bolt (Made to order)
When fastening pipe HB bolts, install the pipe HB nose assembly. Change the
mandrel attached to the tool to the socket that comes with the nose assembly.
Please refer to the following list for each nose assembly component.
●SRB-630-480LF-K2-180L
Nose Assembly
TNM00358
SA Mast Housing
TNM00355
SA Nose Housing
TNM00359
Nose Housing
TNM00258
Nose Slider
TP134-080
Slider Spring
AN600P-31
Retaining Ring
AN600P-32
Nosepiece
TZ024-435
Lock nut
PNT600-03
Button Head Cap Screw
PNT600-100
Spacer
PNT600-138
Socket
TNM00365
●SRB-830-480-K2-70L
Nose Assembly
TNM00360
SA Mast Housing
TNM00355
SA Nose Housing
TNM00361
Nose Housing
TNM00257
Nose Slider
PNT600-137A
Slider Spring
AN600P-31
Retaining Ring
AN600P-32
Nosepiece
TZ034-433
Lock nut
PNT600-03
Button Head Cap Screw
PNT600-100
Spacer
PNT600-138
Socket
TNM00366
Lock Nut
Slider Spring
Nosepiece
Retaining Ring
Nose Slider
Button Head Cap Screw
Nose Housing
SA Mast Housing
Spacer
Socket

9
3. HB Bolt (Made to order)
When tightening HB bolts, replace the mandrel attached to the following nosepiece
and tool with the following socket to make a tool for HB bolts.
HB Bolt
Socket
Nosepiece
SPB-650R-WB*****
PNT600-01-6HB-WB
PNT600-02-6HB-WB
SPB-625-RLT
PNT600-01-6HB
PNT600-02-6HB
4. Slit Nut (Made to order) *Only can be used by Stroke control
When fastening the slit nut, attach the sleeve to the outer diameter of the
mandrel and replace it with the following nose piece. The mandrel used is
PNT600-01-6P.
Slit Nut
Nosepiece
SPH-640-SLIT
PNT600-02-64SLT-S
ENS-M6SV-S
SPH-670-SLIT
PNT600-02-67SLT-S
Nosepiece
Socket
Socket
Sleeve

10
STANLEY Engineered Fastening
4 Shelter Rock Lane
Danbury, Connecticut,
United States, 06810
Tel. [phone]
Fax [phone]
Holding your world together ®
Find your closest STANLEY Engineered Fastening location on
www.stanleyengineeredfastening.com/contact
For an authorized distributor nearby please check
www.stanleyengineeredfastening.com/econtact/distributors
Manual Number
Issue
C/N
TNM00383
0
210406-1
©2021 Stanley Black & Decker, Inc.
Avdel®, Avex®, Avibulb®, Avinox®, Bulbex®, Hemlok®, Interlock®, Klamp-Tite®, Monobolt®, POP®,
ProSet®, Stavex® and T-Lok® are registered trademarks of Stanley Black & Decker, Inc. and its affiliates.
The names and logos of other companies mentioned herein may be trademarks of their respective owners.
Data shown is subject to change without pior notice as a result of continuous product development and
improvement policy. Your local STANLEY Engineered Fastening representative is at your disposal should
you need to confirm latest information.