STAR TRAC FITNESS S-CTx User manual

Star Trac Fitness™
S-CTx Cross Trainer
Install Guide

STAR TRAC S-CTx CROSSTRAINER Install Guide

TRAC SCTX CROSSTRAINER Install Guide
ASSEMBLY AND SETUP
UNPACKING
NOTE: Do not remove the base from the shipping carton at this time.
Remove the top cover from the shipping carton. Remove all parts and shipping supports (except the base) from the carton, and
verify that the following parts are included in your shipment:
Description Qty
Base 1
Display 1
Upper Body Arms 2
End Caps 2
Bolt, Allen Head, __________ 4
Description Qty
Bolt, Hex Head, __________ 8
Screw, Phillips Head, ___________ 8
Flat Washer, ___________ 4
Lock Washer, ___________ 8
TOOLS REQUIRED
Your STAR TRAC S-CTx CROSS TRAINER can be assembled using the following tools:
Metric Hex Key Wrenches
Metric Open-End Wrenches
Metric Ratchet Socket Wrench Set
Torque Wrench
Channel Lock Pliers
Vice Grip Pliers
Rubber Mallet
Phillips Head Screwdriver
Your STAR TRAC S-CTx CROSS TRAINER includes a hex key set and combination open-end wrench.
ASSEMBLY
1. Unpack and Position the Base
CAUTION: The rear end of the base is very heavy. Two persons are
needed to lift this end when moving the base.
Cut the long edge of the shipping carton base at both ends. Fold
the flap down to make a ramp.
With the aid of a helper, lift the rear end of the base, and roll the
base off of the shipping carton platform. Place the base on the floor
in the location where the unit will be used. Be sure the chosen
location is level.
2. Install the Display
NOTE: You will need someone to assist you to install the display.
Have the person who is assisting you hold the display while you
route the display cables and connect the neck.
Have your helper hold the display close the neck on the base. Plug
the display power and I/O cables from the base into the mating
display connectors.
Once display power and I/O cables are connected, route the coaxial
cable up the full length of the display neck before seating the
display unit on the base.
NOTE: The round coaxial cable is not used.
Ste
p
1
Step 2a
STAR

STAR TRAC S-CTX CROSSTRAINER Install Guide
Gently push the display cables down into the neck, and slide the
display into the base. Be sure the display is fully seated. Secure
the display to the base with four M8 allen head bolts and four M8
flat washers. Use two screws in the front side of the neck, and two
in the rear side. Tighten the screws securely to a torque of 8-10
lbs-ft.
3. Install the Upper Body Arms
NOTE: Take care not to install the upper body arms backwards. Be
sure the arms are positioned as shown when installed.
Place on upper body arm on the right-side hub. Be sure the pin in
the arm bracket engages the unthreaded hole on the hub. Secure
the upper body arm to the hub with four hex bolts and four lock
washers. Tighten the bolts securely.
Repeat for the left-side upper body arm.
4. Install the End Caps
NOTE: Be sure the holes in each end cap face the rear of the unit.
Separate the halves of the right-side end cap. Place the end cap halve
around the hub. Use a piece of tape to temporarily hold the end cap
halves together.
Secure the end cap halves together with four Phillips head screws.
Tighten the screws firmly.
Repeat for the left-side end cap.
5. Final Assembly
Be sure all bolt and screws are tightened securely.
If needed, use the leveling adjusters at the rear of the base to level
the unit. Loosen the lock nuts on the adjusters. Rotate the
adjusters until the unit is stabilized, then retighten the lock nuts.
You have now completed assembly of your STAR TRAC S-CTx
CROSS TRAINER.
Step 3
Step 4
Step 2b
Step 5