Star Trac E-SM User manual

Preventative Maintenance
Star Trac E-SM Preventative Maintenance
E-SM
PREVENTATIVE MAINTENANCE
With durable, high performance components, the Star Trac E-SM StairMill is designed for heavy usage
with minimal maintenance required. To keep your Stepper in top condition, Star Trac strongly recommends
performing the regular daily, weekly and monthly pre- ventive maintenance routines outlined below. Any
unusual symptoms, such as a loud continuous noise during operation, should be reported to STAR TRAC
PRODUCT SUPPORT DEPARTMENT at [phone].
DAILY MAINTENANCE
■Remove excessive accumulations of dust, dirt, and other substances by using a clean, soft cloth and a
non-abrasive liquid cleaner, such as Formula 409TM or FANTASTIKTM. Wipe down the exterior of the
display panel, hand rails, pedals, shrouds and heart rate grips.
NOTE: DO NOT spray the cleaner directly onto the Display Panel or heart rate grips.
WEEKLY MAINTENANCE
Perform the following services
each week:
■Vacuum the floor under and around
the StairMill.
■Inspect the Display Panel mounting screws for security, and
retighten if necessary.
■Inspect the Display Panel
keypads for wear.
MONTHLY MAINTENANCE
Perform the following services each month,
or as needed:
■Check that the steps and shrouds
are secure.
■Check the hand rails for looseness. Tighten screws
as necessary.
■Check for smooth and quiet operation of all
moving parts.
MANAGER / MAINTENANCE MODE
After using your Star Trac E-SM StairMill for a period of time, you may wish to
change some of its settings.

Preventative Maintenance
MANAGER MODE
The Manager Mode lets you query and modify the basic settings of your StairMill. To
enter Manager Mode:
1. Press and hold the ,and keys together.
2. A beep will sound and “MANAGER MODE” will display momentarily in the Information Window.
3. Release all keys. “SERIAL NO #####” will display in the
Information Window. NOTE: The system will automatically exit Manager
Mode if no key is pressed for 30 seconds. The following keys are used to
modify settings in MANAGER MODE:
Upper and Lower Data Information Window SCROLL Keys: Display the next and
previous parameters, respectively.
Increase and Decrease LEVEL Keys: Adjust the value of the displayed parameter up and
down, respectively, in increments of 1 unit. These keys do not save the new value - see OK
Key below.
Numeric Keypad: Allows you to enter specific values for numeric parameters. These keys do
not save the new value
- see OK Key below.
OK Key: Updates (saves) the values of all parameters in non-volatile memory, and exits
Manager Mode.
NOTE: To exit Manager Mode without saving any values or settings, press the
QUICK START key.
The items that you may display and change with the previous keys are:
Item Lowest
Value Highest Value Default Value
Meaning
Serial No 0 65535 0 Serial number (set by factory)
Date
01/00
12/99
01/05
Manufacture date for the Stepper (set by factory)
Display Vers 1 01.00 99.99 N/A Display panel software version (set by factory)
Display Vers 2 01.00 99.99 N/A Display panel software version (set by factory)
LCB Vers 01.00 99.99
N/A
Display panel software version (set by factory)
Units English Metric English English = units of pounds, feet,
Metric = units of kilograms, meters
Time 5 99 99 Maximum time in minutes allowed for program, excluding cool-down.
Weight 1 (Lb) 350 (Lb) 155 lbs Default (to user), typical weight in lb (UNITS=English), or kg
1 (KG)
158 (KG)
70 (KG)
(UNITS=Metric).
Language N/A N/A ENGL
Language is English (ENGL), Dutch (DUTC), French (FREN), German (GERM),
Portuguese (PORT), Spanish (SPAN), Swedish (SWED), Italian (ITAL) or

Preventative Maintenance
Katakana (KATA).
MAINTENANCE MODE
Your Service Representative may need to check accumulated data about the past usage of your Star
Trac E-SM StairMill, test its display controls, or investigate error messages. For these reasons, your
Stepper is equipped with a Maintenance Mode. The Maintenance Mode includes all of the items available
through Manager Mode, plus additional items for Service and Diagnostic use. To enter Maintenance Mode:
1. Press and hold the ,and keys together.
2. A beep will sound and “MAINTENANCE MODE” will display momentarily in the Information Window.
3. Release all keys. “SERIAL NO #####” will display in the
Information Window. The following keys are available in
MAINTENANCE MODE:
Upper and Lower Data Information Window SCROLL Keys: Display the next and
previous parameters, respectively. Keys will repeat if held.
Increase and Decrease LEVEL Keys: Adjust the value of the displayed parameter up and
down, respectively, in incre- ments of 1 unit. These keys do not save the new value - see OK
Key below.
Numeric Keypad: Allows you to enter specific values for numeric parameters. These keys do
not save the new value
- see OK Key below.
OK Key: Updates (saves) the values of all parameters in non-volatile memory, and
exits Maintenance Mode. NOTE: To exit Maintenance Mode without saving any values or settings,
press the QUICK START key.

Preventative Maintenance
The items that you may display and change with the
previous keys are:
Item Lowest
Value Highest Value Default Value
Meaning
Serial No
0
65535
0
Serial number (set by factory)
Date 01/00 12/99 01/05 Manufacture date for the StairMill (set by factory)
Display Vers 1 01.00 99.99 N/A Display panel software version (set by factory)
Display Vers 2 01.00 99.99 N/A Display panel software version (set by factory)
LCB Vers 01.00 99.99 N/A Load Control Board software version (set by factory)
Units Time
English
Metric
English
English = units of pounds, feet,
Metric = units of kilograms, meters
Weight
5
99
99
Maximum time in minutes allowed for program, excluding warm-up and cool-
down.
Language
1 (Lb)
350 (Lb)
155 lbs
Default (to user), typical weight in lb (UNITS=English), or kg
1 (KG)
158 (KG)
70 (KG)
(UNITS=Metric).
N/A
N/A
ENGL
Language is English (ENGL), Dutch (DUTC), French (FREN), German (GERM),
Portuguese (PORT), Spanish (SPAN), Swedish (SWED), Italian (ITAL) or
Katakana (KATA).
Model
N/A
N/A
STEPPER
BIKE = Upright Bike / Upright Recumbent
TBT = Total Body Trainer
STEPPER = STEPPER
LCB TYPE
N/A
N/A
VER3
Type of LCB detected by display. Turns
CSAFE
N/A
N/A
OFF
on/off CSAFE functionality. ATSC/NTSC
PVS
N/A
N/A
OFF
or PAL/SECAM, RF signal. Turns the
Wall Power
N/A
N/A
OFF
wall power setting on/off.
AUTO FAN
OFF
ON
ON
Turns on the FAN one minute into the program.
OPER Hours
0 65535 0 Total operating hours.
Quick Start
0 65535 0 Number of times the Quick Start program was run since last reset.
Manual
0 65535 0 Number of times the Manual program was run since last reset.
Fat Burner
0 65335 0 Number of times the Fat Burner program was run since last reset.
IHR Prog
0 65535
0
Number of times the Interval Heart Rate Control program was run since last reset.
CHR Prog
0
65535
0
Number of times the Constant Heart Rate Control program was run since last
reset.
Fit Test
0
65535
0
Number of times the Fitness Test program was run since last reset.
Glt Sculpt
0
65535
0
Number of times the Glute Sculptor program was run since last reset.
Thigh Tnr
0
65535
0
Number of times the Thigh Toner program was run since last reset.
Famous Stp
0
65535
0
Number of times the Famous Steps program was run since last reset.
Comm Lost
0
65535
0
Number of times a “Communication Lost” condition occurred since last reset.
Key Down
0 65535 0 Number of times a “Key Down” condition occurred since last reset.
LED Test
N/A
N/A
N/A
Access to integral LED test function (for use by authorized Maintenance
Technician).
Keypad Test
N/A
N/A
N/A
Access to integral keypad test function (for use by authorized Maintenance
Technician).
Heart Rate
Test N/A N/A N/A Access to integral heart rate system test function (for use by authorized
Maintenance Technician).
Fan Test N/A
N/A
N/A
Access to integral fan test system test function (for use by authorized

Preventative Maintenance
Maintenance Technician).
CSAFE Test
N/A N/A N/A Access to integral CSAFE test system test function (for use by authorized
Maintenance Technician).
Measurements N/A N/A
N/A
Access to integral Measurements function (for use by authorized Maintenance
Technician).
TROUBLESHOOTING
Star Trac E-SM StairMill perform a self-test at the beginning of every workout. If a problem is detected, a
message displays before or after the workout, depending on the nature of the problem. Star Trac
recommends that you refer your questions about your Star Trac E-SM StairMill operation and suspected
malfunctions to Star Trac’s Service Hotline at [phone].
SERVICE MESSAGES
The following messages are displayed if the associated problem is
detected during self-test.
■Key Down - One or more keys on the display panel are stuck in the “on” position. This can occur if a
user presses keys before the system is turned on, or if a key is held down for more than 10 seconds.
Call Star Trac Product Support for assistance if the Key Down message continues to display.