StarTech.com DK30CHHPD User manual

Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: August 28, 2019 8:48 AM
Product Diagram (DK30CHHPD/DK30CHHPDUK/
DK30CHHPDEU/DK30CHHPDAU)
Front
Component Function
1USB-A Port
• Used to charge a connected USB Device.
• Used to connect USB Devices to the Docking
Station (ash drive, etc.).
• BC 1.2 Compliant.
• 7.5W of power output.
• Charges with or without a connection to the
Host Computer.
2USB-C Port
• Used to charge a connected USB Device.
• B.C. 1.2 compliant.
• 7.5 W of power output.
• Charges with or without a connection to the
Host Computer.
33.5 mm Audio Port • Used to connect an Audio Device to the
Docking Station (headset, microphone, etc.).
4Mounting Holes (x 4)
• Used to mount the Docking Station to a desk
or wall.
Note: Located on the bottom of the Docking
Station.
5Power Button • Used to turn the Docking Station On/O.
6 Lock Slot
• Used to secure the Docking Station to a
secure stationary object.
Note: Located on the side of the Docking
Station.
USB-C Dual Video 1080p Monitor, USB 3.1 Gen 1 Dock
Rear
Component Function
7Power Connector
• Used to power the Docking Station by
connecting the Universal Power Adapter to
the Docking Station.
8USB-C Host Port
• Used to connect the Host Computer to the
Docking Station.
• Used to charge the connected Host Computer.
• Power Delivery 3.0.
• 60W of power output.
9HDMI Video 1 and 2
Ports (x 2)
• Used to connect two HDMI Display Devices to
the Docking Station.
• Maximum Resolution: 1920x1200 @ 60 Hz.
10 RJ-45 Port • Used to connect a Network Device to the
Docking Station.
11 USB-A Ports (x 2) • Used to connect USB Devices to the Docking
Station (mouse, keyboard, etc.).
Requirements
For the latest requirements, please visit www.startech.com/DK30CHHPD
Powering the Docking Station
1. Connect the Universal Power Adapter to the Power Connector on the Docking
Station.
2. Connect the Power Cord to the Universal Power Adapter and to an AC Electrical
Outlet.
12345
6
78 9 10 11

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a three-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
2500 Creekside
Parkwy
Lockbourne, Ohio
43137
U.S.A.
1. Use a web browser to navigate to www.startech.com/DK30CHHPD.
2. On the Product page, click the Support tab located in the middle of the screen.
3. In the Drivers and Downloads section, click on the driver link that corresponds with
the operating system running on the host laptop.
4. Once the download is complete, extract the contents of the le.
5. Click the appropriate driver for the version of operating system that you are running
and follow the on-screen prompts to complete the installation.
Resolution Chart
Resolution Frequency Single or
Mirror Mode
Dual Screen
Extended
Full HD (1920 x1080, 1920x1200) 60 Hz Yes Yes
3. Press the Power Button on the Docking Station to turn the Docking Station On.
Connecting a Host Device
• Connect a USB-C Cable to the USB-C Port on the Docking Station and the other end
to a USB-C port on the Host Computer.
Connecting Display Devices
1. Connect an HDMI Cable (sold separately) to the HDMI Video 1 Port on the Docking
Station and the other end to the HDMI port on the Display Device.
2. Repeat step 1 to connect a second Display Device.
Connecting a Network Device
• Connect a CAT 5e/6 Cable to the RJ-45 Port on the Docking Station and the other
end to an RJ-45 port on a Network Device.
Connecting Peripheral Devices
1. (Optional) Connect a USB Storage Device or other USB Peripheral (mouse, tablet,
phone, etc.) to one of the USB-A Ports on the Docking Station.
2. (Optional) Connect a USB Storage Device or other USB Peripheral to the USB-C
Port on the Docking Station.
Driver Installation
Depending on your Host Laptop’s operating system, the required drivers will
automatically be installed when the Docking Station is connected and powered on. If
the drivers do not automatically install: