StarTech.com PDU02IP User manual

Manual Revision: 01/02/2014
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
PDU02IP / PDU02IPSC
2 Port Remote Power Control IP PDU
(Power Distribution Unit)
2 Port Remote Power Control IP PDU with Console
and Sensor Ports
*PDU02IP shown in photo

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Product Diagram ....................................................................................1
Rear View...................................................................................................................................................... 1
Front View .................................................................................................................................................... 1
Introduction............................................................................................2
Packaging Contents ................................................................................................................................. 2
LED Indicators.........................................................................................2
Reset Button ...........................................................................................2
Installation .............................................................................................3
Hardware Installation .............................................................................................................................. 3
Logging In for the First Time................................................................................................................. 4
Web Console Operation ........................................................................6
Power Switch Operation......................................................................................................................... 6
Monitor Section......................................................................................................................................... 7
UPS Status (PDU02IPSC Only)............................................................................................................... 9
Dry Contact Input Indication (PDU02IPSC Only)........................................................................... 10
System Section........................................................................................................................................... 10
Firewall Section.......................................................................................................................................... 15
Account Section ........................................................................................................................................ 17
TimeSync Section...................................................................................................................................... 18
Event Section.............................................................................................................................................. 19

Instruction Manual
ii
Firmware Upgrade Procedure ..............................................................22
Specications..........................................................................................23
Technical Support ..................................................................................24
Warranty Information............................................................................24

Instruction Manual
1
Product Diagram
Rear View
Front View
PDU02IP
PDU02IPSC
Reset Button
LED Indicators
RJ45 LAN
Reset Button
LED Indicators
RJ45 LAN RS232 UPS Console
Dry Contact Input

Instruction Manual
2
LED Indicators
Port Indicators
(Top Row)
LED #1 is illuminated when output receptacle #1 is ON.
LED #2 is illuminated when output receptacle #2 is ON.
Reset Indicator
(Bottom Left)
Reset LED will ash when the Reset function is being
performed.
Power Indicator
(Bottom Right)
Utility Power LED is illuminated when there is an acceptable
AC voltage Present.
Reset Button
If you need to reset the PDU back to factory defaults, the Reset Button is located next
to the LED panel. Insert a paperclip to gently press and hold the Reset Button for at
least 3 seconds, then release.
Reset Button
LED Indicators
RJ45 LAN
The IP address will be reset back to 192.168.1.10
The user name and password will be reset back to admin.
All other settings will be unchanged.
Introduction
Packaging Contents
• 1 x 2 Port PDU
• 1 x Power Cable
• 1 x Instruction Manual (CD)

Instruction Manual
3
Installation
Hardware Installation
1. Connect the power cord to the power inlet and to a wall outlet
2. Plug your equipment into the two output receptacles
3. Connect an Ethernet cable from the PDU to your network
4. Turn the power switch to the ON position
*Optional connections - PDU02IPSC only

Instruction Manual
4
Logging In for the First Time
The minimum requirement to operate the PDU is to setup the IP Address, subnet mask,
and default gateway, which can be done through your web browser or using the IP
Search Utility application on the CD.
Default Settings:
IP address: 192.168.1.10
Subnet mask: 255.255.255.0
Default Gateway: 192.168.1.1
User name / Password: admin / admin (lower case)
Web Browser Method
NOTE: The workstation and the PDU must be on the same LAN
1. Open a web browser and input the default IP address (192.168.1.10)
2. After the login screen appears enter admin / admin for the User name and Password
3. Click on the System tab from the menu bar of the web interface and then click on
Network to set the IP address and network info of this device

Instruction Manual
5
IP Search Utility
NOTE: The workstation and the PDU must be on the same LAN for the IP Search Utility
to detect it, and the Windows Firewall must also be turned o.
1. Open the Windows Control Panel
2. Select Windows Firewall
3. Select O and then click the OK button
4. Insert the provided CD in the CD-ROM drive
5. Launch the IP Search Utility program
6. Click on the Refresh button to search for all PDU02IPxx units on the LAN
7. Click on the detected PDU and congure the IP address, Gateway and Net Mask,
then click the Congure button twice. You will see the values you specied populate
in the main window
8. Repeat step 7 for each device if you have multiple PDU02IPxx units connected
9. Once all devices are congured, close the IP Search Utility program and turn the
Windows Firewall back on

Instruction Manual
6
Web Console Operation
Power Switch Operation
The global outlet controls can be used to either turn all outlets on, or all outlets o,
while each individual outlet allows for On / O / Reboot controls.
• Double clicking the ALL ON button will turn ON both outlets. Double clicking on the
ALL OFF button will turn OFF all of the outlets.
• Double clicking the switch for Port 1 or Port 2 will ip the switch to the opposite
state (ON/OFF) for that individual outlet.
• If you want to Reboot (cycle o, then back on) an individual outlet, check the
Reboot box and then double click on the switch.
ON OFF No Power
Not Authorized
(User account
restruction)