Steel mate PTS810 V10 User manual

Steelmate Industrial Park, Heping Street, Dongfu Road, Dongfeng Town,
Zhongshan City, Guangdong, P.R. China 528425
STEELMATE CO., LTD.
Front & Rear Parking Assist System
PTS810 V10
Manual
PRI0886R/A
Think safety think Steelmate
Steelmate Co., Ltd. All rights reserved.
The right to change the design and specifications reserved.
The trademark, patent and copyright are owned by
Steelmate Co., Ltd.
www.eldibg.com
car audio & multimedia system

01
User Manual
Contents
02
02
02
03
03
03
04
05
05
06
07
09
13
13
14
15
15
16
23
24
25
Important notice ----------------------------------------
Disclaimer -----------------------------------------------
About the product --------------------------------------
Key features --------------------------------------------
Specifications -------------------------------------------
LCD display ---------------------------------------------
Self-testing function -----------------------------------
Volume adjustment ------------------------------------
Voice adjustment --------------------------------------
Learning function for cars with tow-bar or spare
wheel -----------------------------------------------------
Dual intelligent function ------------------------------
How does the system work -------------------------
Attention -------------------------------------------------
Sensor maintenance ----------------------------------
Brief installation diagram ----------------------------
Includes --------------------------------------------------
Installation tools ----------------------------------------
Sensor installation -------------------------------------
Wire connection ----------------------------------------
Functional test ------------------------------------------
Troubleshooting ----------------------------------------
User Manual Installation Manual
www.eldibg.com
car audio & multimedia system

02 03
The PAS is designed as a driver assistance device,
and should not be used as a substitute for safe
parking practices. The area into which the vehicle
is to be reversed must be constantly visually
monitored while parking.
The manufacturer and its distributors do not
guarantee or assume liability for collisions or
damages while reversing the vehicle.
Parking Assist System (PAS) helps to provide
assistance when reversing and parking. Driving
skills such as slowing down, use of mirrors etc. is
always essential.
This system is for vehicles with 9~16V DC only.
This system should be installed by a professional
auto technician.
Route wiring harness away from heat source
and electrical components.
It is strongly recommended to check the position
of the sensors before the actual drilling of the
holes.
Perform a functional test after installation.
1.
2.
3.
4.
5.
This PAS comes with 8-sensor and a display that
is an ultrasonic detects the area behind the vehicle
while reversing and driving forward, and alerts with
audible tones & visual warnings, if the system
detects an obstacle. It assists the driver
when parking and in manoeuvring situation.
PTS800V10 is a front and rear parking assist
system with slim black LCD display. All the
detachable sensors are waterproof and can be
easily changed. Combined with the anti-interference
and anti-false alert technology, the system can
detect obstacles in any weather conditions and
response quickly. The system has intelligent
detection, which is ideal for vehicles with tow-bar
or spare tire.
Every part of the product has passed the most
stringent test before releasing to the market. It is
reliable at a wide storage temperature range (-
40 C~+85 C/ -40 F~+185 F) and becomes very
useful when you are parking at a raining day,
snowing day or at night etc. With the help of parking
assist system, you can enjoy a comfortable, relaxed
and safer parking experience.
9~16V
<350mA
-40 C~+80 C/ -40 F~+176 F
-20 C~+70 C/ -4 F~158 F
-40 C~+85 C/ -40 F~+185 F
0.30m~2.59m/ 1.0ft~8.4ft
70~90dB
Operating voltage:
Operating current:
Operating temperature:
ECU:
Display:
Storage temperature:
Detection range:
Siren SPL:
Slim black display with digital showing
Complete front & rear car protection with 8-
sensor
Can change to 6-sensor system (2 front + 4rear)
1 control unit and 1 display for easy installation
All weather design
Sensor with waterproof wire connector
Voice/ beep alert selectable
Anti-false alert technology
Intelligent detection for vehicles with tow-bar,
spare tire or other protrusion
Self-test function
l
l
l
l
l
l
l
l
l
l
Detection range:
Front:
Rear:
0.30~0.89m/ 0.3~3.2ft
0.30~0.59m/ 0.3~1.9ft
(reversing)
0.30~2.59m/ 0.3~8.4ft
Important notice
Disclaimer
About the product Key features
Specifications
LCD display
Digital distance
Matrix obstacle position
SET button Speaker
Universal joint
Pedestal
www.eldibg.com
car audio & multimedia system

04 05
Self-testing function Volume adjustment
Voice adjustment
Once ACC ON and reverse gear is selected. press "SET" button to select the volume level, it will saved and
exit after 1 second later. ("3" for Max, "2" for Middle, "1" for Min)
Default setting: Max volume
1. When ACC ON, the system will test 4 front sensor (E,F,G,H) automatically.
1) Normal 2) Damaged or defective sensor is detected
3) Once the self-test procedure is completed, when you press the footbrake, the system will detect in front of
the vehicle for 5 seconds.
1) Normal 2) Damaged or defective sensor is detected
When detected damaged/ defective sensor:
Beep 3 times for alarm
Other proper sensors will keep working after the alarm
No. of sensor damage/ defective (E1~E6) will be show
on the display together with the corresponding LCD lights
on for showing which sensor(s) is(are) damaged/ defective
The system will not alarm when sensors (F&G) are
damaged/ defective as it will work as 2-sensor system
automatically.
Once ACC ON and reverse gear is selected, press "SET" button for 2 seconds with "Bi" sound once enter the
voice adjustment mode.. Then press the SET button again to turn ON/ OFF the voice function.
Default setting: Voice alarm turn on
"00": Voice alarm turn off
"01": Voice alarm turn on
2. When reverse gear is selected, the system will teat (A,B,C,D,E,H) sensors automatically.
3) Once the self-test procedure is completed,
the system will detect rear of the vehicle
automatically.
Be---Be---Be---No beep
Be--- Be---Be---Be---
l
l
l
l
Normal & no obstacle
www.eldibg.com
car audio & multimedia system

06 07
Learning function for cars with tow-bar or spare wheel Dual intelligent function
Clearing the learning function:
X10
+
1"
Be------
1.
2.
3.
4.
With the ignition "ON", change the gear from "N" to "R" for 10 times (Each gear change must be within
1 second)
After 10th times, leave the gear in "R" position.
The display will beep and flash once to complete the learning process.
When the learning function is activated, the system will ignore the tow bar or spare wheel and only
detect other object behind the vehicle.
1.
2.
3.
With the ignition "ON", change the gear from "N" to "R" for 12 times (Each gear change must be within
1 second)
After 12th times, leave the gear in "R" position.
The display will beep and flash once will dark in turn to indicate that learning function is cleared
successfully and the system is reset.
When this function is ON, the detected distance will increase 20cm between the sensor and obstacle
which is designed for the tow-bar/ Spare wheel.
Jumper position: "0" (Default setting)
Normal detected distance Jumper position: "20" The detected distance from sensor to obstacle
should be increased 20cm.
Note:
1. If you make a mistake while carrying out the above procedure, leave vehicle in the "R" position for 2
seconds to clear the system memory and then start the procedure again.
2. If the vehicle does not have tow-bar or spare wheel, you do not need to use this function.
0.5m
0.3m
www.eldibg.com
car audio & multimedia system

08 09
Distance: (<0.30m/1.0ft)Distance: 0.4m/1.2ftDistance: >0.6m/2.0ft
Driving forward (6 sensors)
Be---Be--- Be------
Jumper position: "55~65cm"
Normal sensor sensitivity
Recommended for the sensor which is installed
between 55~65 cm from ground
Jumper position: "45~54cm" (Default setting)
Low sensor sensitivity
Recommended for the sensor which is installed
between 45~54 cm from ground
How does the system work
Sensor sensitivity adjustment
www.eldibg.com
car audio & multimedia system

10 11
Distance: >1.0m/3.3ft Distance: 0.4m/1.2ft Distance: (<0.30m/1.0ft) Distance:<0.3m/1.0ft Distance:0.8m/2.6ft Distance:>1.5m/4.9ft
Driving forward (8 sensors)
+12V +12V +12V
Reversing
Be---Be--- Be------ Be------ Be---Be--- No Beep
www.eldibg.com
car audio & multimedia system

12 13
Attention Sensor maintenance
Be--Be--Be--
Distance: 0.4m/1.3ft Be--------
Distance:<0.3m/1.0ft
Zigzag reversing
After installation, please fully test the system
before use.
Heavy rain, dirty or damaged sensors may
result in false alarm occasionally.
Ensure that the self-test procedure is comple-
ted and all sensors are functioning before
reversing.
l
l
l
False detection may occur in the following
situations:
Do not wash the sensor with squirt gun or swab
them forcibly.
Please wash car with low-pressure water.
Please melt the ice with water when the sensors
are covered by ice.
Please clean the sensors with cloth or low-
pressure water when the sensors are covered
by mud or snow.
www.eldibg.com
car audio & multimedia system

14 15
Installation Manual
60' ~ 80'
Brief installation diagram
Includes
Installation tools
Manual
The above graphics are for reference only.
Display
ECU
www.eldibg.com
car audio & multimedia system

16 17
L1 L2 L1
H
H > 45cm/1.5ft
H < 65cm/2.1ft
1.5m/4.9ft
1.0m/3.3ft
35cm/1.1ft<L1<45cm/1.5ft
45cm/1.5ft<L2<55cm/1.8ft
45cm/1.5ft<H<65cm/2.1ft
The sensor head angle can be changed to compensate for angled bumpers. Please see the instructions overleaf.
Sensor installation
H > 45cm/1.5ft
H < 65cm/2.1ft
H > 65cm/2.1ft
=1/8L
=2/8L
=1/8L
< 45cm/1.5ft < 45cm/1.5ft < 45cm/1.5ft
H < 45cm/1.5ft
a
b
c
c b a a b c
45cm/1.5ft < H < 65cm/2.1ft
H G F E
Notes:
For 2-sensor system, recommended to install 2 sensors on position
E&H for the best performance.
On some vehicles, due to the number plates location or bumper
design, the distance between the centre of two sensors (L2) will
be greater, i.e. L2>60cm. The kit will still function, however the
detection of narrow objects i.e. posts will be reduced.
1.
2.
2
1
www.eldibg.com
car audio & multimedia system

18 19
Change of sensor cover.
(Built-in)
Tips: Make sure the degree
marking is on the top of
sensor after plug in.
3
00 40 100
4
Check the size of the hole saw
packed in the product to be matching
the diameter of the sensors before
drilling any holes.
www.eldibg.com
car audio & multimedia system

20 21
ABCD
E
F
G
H
Bumper Gap
Hint: If a gap found between bumper and 10osensor cover after installation, please adjust the angle
of the hole shown as below.
Angle
56 7
8
www.eldibg.com
car audio & multimedia system

22 23
Wire connection
Display
ECU
ABCDEFGH
H
G
F
E
D
C
B
A
Black
White
GNG
ACC+Reversing light
Red
Footbrake light
Pink
www.eldibg.com
car audio & multimedia system

24 25
Functional test Troubleshooting
1. After installation, the buzzer/display doesn't
work.
Make sure the wires connected properly.
Make sure the vehicle is ACC ON.
Make sure the reverse gear is selected (the
reversing light should be lighted on).
2. Damaged sensor detected
Make sure ALL sensors plugged into the ECU
correctly and tightly.
Make sure no snow or dirt covered on the
sensor.
Please check the sensor is damaged or not.
3. False alarm
Make sure ALL sensors plugged into the ECU
in the correct position tightly.
Please check if any of sensors detected the
ground.
Please check if the rubber ring of the sensor
came out (if sensor comes with rubber ring).
4. Display alarm sound is too low or too high
Press the SET or volume button to adjust the
volume to a suitable level.
5. If the problem persists, please follow below.
For consumer: Please contact the nearby
dealer or customer service center.
For installer/dealers:
Test the sensors with a certified ECU by
performing a functional test.
Replace another ECU and retest the sensors.
Plug the certified sensors into the ECU and
performing a functional test again.
Please email us at [email protected]
about the problems with details.
Functional testing is possible
by holding a wooden board
(0.3 x1.0m/1x3.3ft) standing
at the front or rear of the car,
and drive the car forward and
backward to test each
function respectively as
shown in this manual.
1.0m/3.3ft
Rear sensor function test
Front sensor function test
0.3m/1.0ft
2.5m/8.2ft
l
l
l
l
l
l
l
l
l
l
l
l
l
l
a.
b.
www.eldibg.com
car audio & multimedia system