STI Stopper Station Series User manual

S OPPER®S A ION
SERIES SS-2008
PUSH BU ON
PNEUMA IC IMER BU ON
ADA
Compliant
Pneumatic Timer Model
SS-2008 ed
SS-2108 Green
SS-2208 Yellow
SS-2308 White
SS-2408 Blue
ALL MODELS COME WITH A
COLO MATCHED SU FACE
MOUNT BACKBOX

This push button has been tested according to UL38 and UL2017. Manual fire
alarm stations are listed in UL category UNIU and non-fire alarm initiating devices
are listed in UL category UEHX. It is important to read, understand and follow all
instructions provided with this product. It is the installer’s responsibility to com-
ply with NFPA72 and 101, NEC, mounting specifications according to ADA and
other applicable fire and electrical codes. After installation and testing are com-
plete, provide a copy of this manual to all personnel responsible for testing and
maintenance of this product. To avoid electrical shock, DO NOT attempt to install
this product when power is on.
- 1 -

Installation and Service Instructions
S OPPER®S A ION SERIES SS-2008
PUSH BU ON PNEUMAIC IMER
SAFE Y NO ICE O INS ALLERS AND USERS
I. GENERAL
Product Dimensions See page 3
Contact Rating One set NO and one set NC
ated at 10 AMP @ 240 VAC
ecognized component listing is
1,000,000 cycles
II. CON EN S LIS
QTY. DESCRIPTI N
1 Push Button Housing Assembly
1 19001 Allen Head Screw #8-32 x 3/8 in.
1 19015 Allen Wrench 3/32 in.
4 19068 #6 x 5/8 in. hi-low screw
2 19060 Screw #6-32 x 1 in.
1 19021 Ground Screw
4 19039 #6 x 1 1/4 in. SS SMS
4 19018 Plastic Screw Anchor
1 71100A Surface Backbox
1 Warranty Card
III. INS RUC IONS
Product Dimensions .......................................................................... Page 3
Front Housing emoval .................................................................... Page 3
Backbox Preparation ........................................................................ Page 4
Switch Contact Diagram.................................................................... Page 5
Switch Data........................................................................................ Page 5
Installation ........................................................................................ Page 6
- 2 -

VIEW SHOWING FRON HOUSING REMOVAL
- 3 -
PRODUC DIMENSIONS
19011 SCREW ALLEN HEAD
#8 - 32 x 3/8 (1) PROVIDED
BUTTON AND SWITCH ASSEMBLY
19015 WRENCH
(1) PROVIDED
10271 SWITCH HOUSING
RED, GREEN, YELLOW,
WHITE AND BLUE
QTY. PART No. NAME
P
4
1 1
1 2
1
QTY. PART No. NAME
P
3
3
4
1 1
1 2
1
12
9
IS NOT USED
1
1.62 in.
(41mm)
4.87in.
(124mm)
1.5 in.
(38mm)
1.375 in.
(35mm)
QTY. PART No. NAME
P
3
4
1 1
1 2
1
12
9
IS NOT USED
1
3.5mm x 13mm
(
3.25 (82mm)

H
J
BOX MUST BE INSTALLED WITH
"TOP" FACING UPWARD AS SHOWN
SWITCH BACKPLATE
MOUNTING BOSS
H (4 PLACES)
GROUND SCREW BOSS
THESE (4) HOLES MUST
BE DRILLED OUT USING
A 3/16 in. DRILL BIT
J(4 PLACES)
F
H
H H
J
J
J
TOP
BACKBOX PREPARA ION
(N T INCLUDED WITH FLUSH M UNT C VERS)
2.375 in.
(60mm)
.75 in.
(19mm)
1.5 in.
(38mm)
.75 in.
(19mm)
FIELD DRILLING F R C NDUIT
ENTRY IS REQUIRED. L CATI NS
SH WN ALS APPLY T PP SITE,
PARALLEL SIDES.
- 4 -

INS ALLA ION NO E:
ADA mounting compliance requires the
operable part of the initiating device
shall not be less than 1.1m
(3 1/2 ft.) or greater than 1.37m
(4 1/2 ft.) above finished floor service.
CON AC DIAGRAM
SWI CH INFORMA ION
- 5 -
CON AC S
One set NO and one set NC
LEAD WIRE C L RS
IN PARENTHESIS.
QTY. PART No. NAME
P
4
1 1
1 2
1
QTY. PART No. NAME
P
3
3
4
1 1
1 2
1
12
9
IS NOT USED
1
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
FAST
SLOW
TIMER RANGE ADJUSTMENT SCREW
* IF NEEDED, MAKE VERY SMALL
ADJUSTMENTS*
TURN COUNTER CLOCKWISE
TO INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
FACTORY SETTING - 25 TO 45 SECONDS
PART No. NAME
P
3
4
1 1
1 2
1
12
18 x 1
A
6-32 x 1. 00
1
SETTING – 25 TO 45 SECONDS
F
QTY. PART No. NAME
P
3
3
4
1 1
1 2
1
8 x 1
A
IS NOT USED
1
6-32 x 1. 00
1
QTY. PART No. NAME
P
3
4
11
12
1
QTY. PART No. NAME
P
3
3
4
11
1 2
1
12
9
IS NOT USED
1
NC
NO
NC
NO

PNEUMA IC IMER
MODEL
WI HOU PROVIDED
SURFACE BACKBOX
- 6 -
PNEUMA IC IMER
MODEL
WI H PROVIDED
SURFACE BACKBOX
INS ALLA ION
QTY. PART No. NAME
P
3
4
1 1
1 2
1
8 x 1
A
6-32 x 1. 00
1
QTY. PART No. NAME
P
3
4
1 1
1 2
1
IS NOT USED
1
DRILL (4)
3/16 DIA. HOLES
71100A SURFACE BOX
RED, GREEN, YELLOW, WHITE AND BLUE
19068 SCREW
SELF TAPPING (4) PROVIDED
19014 SCREW #8 X 1 (4) PROVIDED
IF WIRE ACCESS OR CONDUIT ENTRY
HOLES ARE NEEDED, THESE HOLES
MUST BE FIELD DRILLED AS REQUIRED.
19018 ANCHOR (4) PROVIDED
19021 GROUND LUG
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND JUMPER WIRE NOT PROVIDED
QTY. PART No. NAME
P
3
4
11
12
1
QTY. PART No. NAME
P
3
4
11
1 2
1
IS NOT USED
1
TYPICAL FLUSH MOUNT
GANG BOX
19021 GROUND LUG
(2) PROVIDED
19010 SCREW
#6-32 X 1
(2) PROVIDED
BUTTON AND
SWITCH ASSEMBLY
CAN BE INSTALLED
ON ANY EXISTING
SINGLE GANG BOX

Safety echnology International, Inc.
2306 Airport Rd • Waterford, MI 48327
Phone: [phone] • Fax: [phone]
800-888-4STI (4784) • www.sti-usa.com
Safety echnology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: [phone]
Fax: [phone] • Freephone: 0800 085 1678 (UK only)
E-mail: [email protected] • Web: www.sti-europe.com
2008 A-IS
02/04