STI UB-1PN User manual

UB-1PN Universal
Pneumatic Button
We protect the things that protect you.®
ADA
Compliant
ADA
Compliant

NOTES
It is important to read, understand and follow all instructions provided with this
product. It is the installer’s responsibility to comply with NFPA 70 & 101, NEC,
mounting specifications according to ADA and other applicable electrical codes.
To avoid electrical shock, DO NOT attempt to install this product when power
is on. ADA mounting compliance requires the operable part of the initiating
device shall not be less than 3 1/2 ft. (1.1m ) or greater than 4 1/2 ft. (1.37m)
above finished floor surface. After installation and testing are complete, provide
a copy of this manual to all personnel responsible for testing and maintenance
of this product.
* For access control installations, power for the UB-1PN must be supplied by a
power source Listed to UL294. When used for access control, this device shall
be used as a part of an access controlled egress door system. It is up to the
local AHJ to allow use of this device in place of an automatic sensor. For higher
security installations, lower time limits should be used.
SWITCH RATING
Independent Form “Z” contacts
Rated at: 10A @ 240 VAC
Operating Temp: 15° to 120°F (-9° to 49°C)
1,000,000 Cycles
- 2 -
4.83 in.
(123mm)
3.22 in.
(82mm) .91 in.
(23mm)
1.47 in.
(38mm)
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
SQUEEZE TABS AND PUSH
ASSEMBLY INTO PLATE
A
A
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
NO
NC
COM
LED –
LED +
SWITCH 1
SWITCH 2
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
NC
COM
NO
MAG LOCK
UB-1L LED PCB
UL Listed
NORMAL POSITION BUTTON ACTIVATED
MAGNETIC LOCK
MESSAGE LAMP
ON
OFF
OFF
ON
+
+
+
12-24 VDC Power Supply
NC
NO
NC
NO
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
OFF
ON
+
+
+
MAG LOCK
NC CONTACTS
NO CONTACTS
UB-1L LED PCB
UL Listed
12-24 VDC Power Supply
NORMAL POSITION BUTTON ACTIVATED
ON
OFF
MAGNETIC LOCK
MESSAGE LAMP
UB-1L LED PCB
NYLON WASHER
SCREW
COUNTERCLOCKWISE
CLOCKWISE
TIMER RANGE ADJUSTMENT SCREW
ADJUSTMENT RANGE - 2 TO 60 SECONDS
TIMER FACTORY SET TO MINIMUM TIME
SETTING. TO INCREASE TIME, TURN
SCREW CLOCKWISE IN 1/4 TURN
INCREMENTS. WHEN CLOSE TO DESIRED
TIME, TURN SCREW IN VERY FINE
INCREMENTS TO DESIRED SETTING.
CAUTION: OVER-TIGHTENING MAY
CAUSE DAMAGE TO TIMER.
CONNECTION AND LEAD WIRE
COLOR CODE
12
34
SCREWDRIVER

1. TO CHANGE BUTTON COLOR AND ROUND MESSAGE
1. Choose button message and color. If same as existing, proceed to 2.
2. If choosing a new message, remove button. On the back side of the plate, squeeze tabs
and push actuator assembly into plate just enough to grasp the button and remove.
3. From the front of the plate, push actuator back into original position.
4. Choose button message. Blank plate is available for your custom message.
a. Insert button message, align 4 notches on actuator.
b. Select color lens. Align top and bottom notches with tabs on
actuator and push until it snaps together.
1. Remove LED circuit board.
2. Remove current message by pushing in
and down on tabs 1and 2with a small
screwdriver. If necessary, also push in and
down on tabs 3and 4. Once message is
loose, remove from the front of the plate.
3. Select new message and snap into place.
Blank plates are included to create your
own custom message.
2. CHANGE TOP MESSAGE
- 3 -
4.83 in.
(123mm)
3.22 in.
(82mm) .91 in.
(23mm)
1.47 in.
(38mm)
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
SQUEEZE TABS AND PUSH
ASSEMBLY INTO PLATE
A
A
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
NO
NC
COM
LED –
LED +
SWITCH 1
SWITCH 2
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
NC
COM
NO
MAG LOCK
UB-1L LED PCB
UL Listed
NORMAL POSITION BUTTON ACTIVATED
MAGNETIC LOCK
MESSAGE LAMP
ON
OFF
OFF
ON
+
+
+
12-24 VDC Power Supply
NC
NO
NC
NO
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
OFF
ON
+
+
+
MAG LOCK
NC CONTACTS
NO CONTACTS
UB-1L LED PCB
UL Listed
12-24 VDC Power Supply
NORMAL POSITION BUTTON ACTIVATED
ON
OFF
MAGNETIC LOCK
MESSAGE LAMP
UB-1L LED PCB
NYLON WASHER
SCREW
COUNTERCLOCKWISE
CLOCKWISE
TIMER RANGE ADJUSTMENT SCREW
ADJUSTMENT RANGE - 2 TO 60 SECONDS
TIMER FACTORY SET TO MINIMUM TIME
SETTING. TO INCREASE TIME, TURN
SCREW CLOCKWISE IN 1/4 TURN
INCREMENTS. WHEN CLOSE TO DESIRED
TIME, TURN SCREW IN VERY FINE
INCREMENTS TO DESIRED SETTING.
CAUTION: OVER-TIGHTENING MAY
CAUSE DAMAGE TO TIMER.
CONNECTION AND LEAD WIRE
COLOR CODE
12
34
SCREWDRIVER
4.83 in.
(123mm)
3.22 in.
(82mm) .91 in.
(23mm)
1.47 in.
(38mm)
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
SQUEEZE TABS AND PUSH
ASSEMBLY INTO PLATE
A
A
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
NO
NC
COM
LED –
LED +
SWITCH 1
SWITCH 2
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
NC
COM
NO
MAG LOCK
UB-1L LED PCB
UL Listed
NORMAL POSITION BUTTON ACTIVATED
MAGNETIC LOCK
MESSAGE LAMP
ON
OFF
OFF
ON
+
+
+
12-24 VDC Power Supply
NC
NO
NC
NO
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
OFF
ON
+
+
+
MAG LOCK
NC CONTACTS
NO CONTACTS
UB-1L LED PCB
UL Listed
12-24 VDC Power Supply
NORMAL POSITION BUTTON ACTIVATED
ON
OFF
MAGNETIC LOCK
MESSAGE LAMP
UB-1L LED PCB
NYLON WASHER
SCREW
COUNTERCLOCKWISE
CLOCKWISE
TIMER RANGE ADJUSTMENT SCREW
ADJUSTMENT RANGE - 2 TO 60 SECONDS
TIMER FACTORY SET TO MINIMUM TIME
SETTING. TO INCREASE TIME, TURN
SCREW CLOCKWISE IN 1/4 TURN
INCREMENTS. WHEN CLOSE TO DESIRED
TIME, TURN SCREW IN VERY FINE
INCREMENTS TO DESIRED SETTING.
CAUTION: OVER-TIGHTENING MAY
CAUSE DAMAGE TO TIMER.
CONNECTION AND LEAD WIRE
COLOR CODE
12
34
SCREWDRIVER

3. INSTALL OR REMOVE CONTACT BLOCK
- 4 -
INSTALL
To attach, align tabs (as shown) and
gently snap top, then bottom.
Be sure to hear BOTH tabs snap
into place. Contacts can be rotated
180° if desired.
REMOVE
To remove, use
a small flat blade
screwdriver.
Position screwdriver
blade under tab
and gently rotate
screwdriver until tab
disengages. Repeat
for opposite tab.
4.83 in.
(123mm)
3.22 in.
(82mm) .91 in.
(23mm)
1.47 in.
(38mm)
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
SQUEEZE TABS AND PUSH
ASSEMBLY INTO PLATE
A
A
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
NO
NC
COM
LED –
LED +
SWITCH 1
SWITCH 2
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
NC
COM
NO
MAG LOCK
UB-1L LED PCB
UL Listed
NORMAL POSITION BUTTON ACTIVATED
MAGNETIC LOCK
MESSAGE LAMP
ON
OFF
OFF
ON
+
+
+
12-24 VDC Power Supply
NC
NO
NC
NO
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
OFF
ON
+
+
+
MAG LOCK
NC CONTACTS
NO CONTACTS
UB-1L LED PCB
UL Listed
12-24 VDC Power Supply
NORMAL POSITION BUTTON ACTIVATED
ON
OFF
MAGNETIC LOCK
MESSAGE LAMP
UB-1L LED PCB
NYLON WASHER
SCREW
COUNTERCLOCKWISE
CLOCKWISE
TIMER RANGE ADJUSTMENT SCREW
ADJUSTMENT RANGE - 2 TO 60 SECONDS
TIMER FACTORY SET TO MINIMUM TIME
SETTING. TO INCREASE TIME, TURN
SCREW CLOCKWISE IN 1/4 TURN
INCREMENTS. WHEN CLOSE TO DESIRED
TIME, TURN SCREW IN VERY FINE
INCREMENTS TO DESIRED SETTING.
CAUTION: OVER-TIGHTENING MAY
CAUSE DAMAGE TO TIMER.
CONNECTION AND LEAD WIRE
COLOR CODE
12
34
SCREWDRIVER
4.83 in.
(123mm)
3.22 in.
(82mm) .91 in.
(23mm)
1.47 in.
(38mm)
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
SQUEEZE TABS AND PUSH
ASSEMBLY INTO PLATE
A
A
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
NO
NC
COM
LED –
LED +
SWITCH 1
SWITCH 2
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
NC
COM
NO
MAG LOCK
UB-1L LED PCB
UL Listed
NORMAL POSITION BUTTON ACTIVATED
MAGNETIC LOCK
MESSAGE LAMP
ON
OFF
OFF
ON
+
+
+
12-24 VDC Power Supply
NC
NO
NC
NO
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
OFF
ON
+
+
+
MAG LOCK
NC CONTACTS
NO CONTACTS
UB-1L LED PCB
UL Listed
12-24 VDC Power Supply
NORMAL POSITION BUTTON ACTIVATED
ON
OFF
MAGNETIC LOCK
MESSAGE LAMP
UB-1L LED PCB
NYLON WASHER
SCREW
COUNTERCLOCKWISE
CLOCKWISE
TIMER RANGE ADJUSTMENT SCREW
ADJUSTMENT RANGE - 2 TO 60 SECONDS
TIMER FACTORY SET TO MINIMUM TIME
SETTING. TO INCREASE TIME, TURN
SCREW CLOCKWISE IN 1/4 TURN
INCREMENTS. WHEN CLOSE TO DESIRED
TIME, TURN SCREW IN VERY FINE
INCREMENTS TO DESIRED SETTING.
CAUTION: OVER-TIGHTENING MAY
CAUSE DAMAGE TO TIMER.
CONNECTION AND LEAD WIRE
COLOR CODE
12
34
SCREWDRIVER
CONTACT INFORMATION
CONTACT REMOVAL
DETAIL A

- 5 -
4. ATTACH POWER FOR LED (if desired)
(See drawing)
4.83 in.
(123mm)
3.22 in.
(82mm) .91 in.
(23mm)
1.47 in.
(38mm)
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
SQUEEZE TABS AND PUSH
ASSEMBLY INTO PLATE
A
A
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
NO
NC
COM
LED –
LED +
SWITCH 1
SWITCH 2
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
NC
COM
NO
MAG LOCK
UB-1L LED PCB
UL Listed
NORMAL POSITION BUTTON ACTIVATED
MAGNETIC LOCK
MESSAGE LAMP
ON
OFF
OFF
ON
+
+
+
12-24 VDC Power Supply
NC
NO
NC
NO
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
OFF
ON
+
+
+
MAG LOCK
NC CONTACTS
NO CONTACTS
UB-1L LED PCB
UL Listed
12-24 VDC Power Supply
NORMAL POSITION BUTTON ACTIVATED
ON
OFF
MAGNETIC LOCK
MESSAGE LAMP
UB-1L LED PCB
NYLON WASHER
SCREW
COUNTERCLOCKWISE
CLOCKWISE
TIMER RANGE ADJUSTMENT SCREW
ADJUSTMENT RANGE - 2 TO 60 SECONDS
TIMER FACTORY SET TO MINIMUM TIME
SETTING. TO INCREASE TIME, TURN
SCREW CLOCKWISE IN 1/4 TURN
INCREMENTS. WHEN CLOSE TO DESIRED
TIME, TURN SCREW IN VERY FINE
INCREMENTS TO DESIRED SETTING.
CAUTION: OVER-TIGHTENING MAY
CAUSE DAMAGE TO TIMER.
CONNECTION AND LEAD WIRE
COLOR CODE
12
34
SCREWDRIVER
CONTACT DIAGRAM
4.83 in.
(123mm)
3.22 in.
(82mm) .91 in.
(23mm)
1.47 in.
(38mm)
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
SQUEEZE TABS AND PUSH
ASSEMBLY INTO PLATE
A
A
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
NO
NC
COM
LED –
LED +
SWITCH 1
SWITCH 2
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
NC
COM
NO
MAG LOCK
UB-1L LED PCB
UL Listed
NORMAL POSITION BUTTON ACTIVATED
MAGNETIC LOCK
MESSAGE LAMP
ON
OFF
OFF
ON
+
+
+
12-24 VDC Power Supply
NC
NO
NC
NO
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
OFF
ON
+
+
+
MAG LOCK
NC CONTACTS
NO CONTACTS
UB-1L LED PCB
UL Listed
12-24 VDC Power Supply
NORMAL POSITION BUTTON ACTIVATED
ON
OFF
MAGNETIC LOCK
MESSAGE LAMP
UB-1L LED PCB
NYLON WASHER
SCREW
COUNTERCLOCKWISE
CLOCKWISE
TIMER RANGE ADJUSTMENT SCREW
ADJUSTMENT RANGE - 2 TO 60 SECONDS
TIMER FACTORY SET TO MINIMUM TIME
SETTING. TO INCREASE TIME, TURN
SCREW CLOCKWISE IN 1/4 TURN
INCREMENTS. WHEN CLOSE TO DESIRED
TIME, TURN SCREW IN VERY FINE
INCREMENTS TO DESIRED SETTING.
CAUTION: OVER-TIGHTENING MAY
CAUSE DAMAGE TO TIMER.
CONNECTION AND LEAD WIRE
COLOR CODE
12
34
SCREWDRIVER
4.83 in.
(123mm)
3.22 in.
(82mm) .91 in.
(23mm)
1.47 in.
(38mm)
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
SQUEEZE TABS AND PUSH
ASSEMBLY INTO PLATE
A
A
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
NO
NC
COM
LED –
LED +
SWITCH 1
SWITCH 2
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
NC
COM
NO
MAG LOCK
UB-1L LED PCB
UL Listed
NORMAL POSITION BUTTON ACTIVATED
MAGNETIC LOCK
MESSAGE LAMP
ON
OFF
OFF
ON
+
+
+
12-24 VDC Power Supply
NC
NO
NC
NO
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
OFF
ON
+
+
+
MAG LOCK
NC CONTACTS
NO CONTACTS
UB-1L LED PCB
UL Listed
12-24 VDC Power Supply
NORMAL POSITION BUTTON ACTIVATED
ON
OFF
MAGNETIC LOCK
MESSAGE LAMP
UB-1L LED PCB
NYLON WASHER
SCREW
COUNTERCLOCKWISE
CLOCKWISE
TIMER RANGE ADJUSTMENT SCREW
ADJUSTMENT RANGE - 2 TO 60 SECONDS
TIMER FACTORY SET TO MINIMUM TIME
SETTING. TO INCREASE TIME, TURN
SCREW CLOCKWISE IN 1/4 TURN
INCREMENTS. WHEN CLOSE TO DESIRED
TIME, TURN SCREW IN VERY FINE
INCREMENTS TO DESIRED SETTING.
CAUTION: OVER-TIGHTENING MAY
CAUSE DAMAGE TO TIMER.
CONNECTION AND LEAD WIRE
COLOR CODE
12
34
SCREWDRIVER
CONTACTS
One set NO and one set NC

- 6 -
5. MOUNT BUTTON ONTO ELECTRICAL BOX
4.83 in.
(123mm)
3.22 in.
(82mm) .91 in.
(23mm)
1.47 in.
(38mm)
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
SQUEEZE TABS AND PUSH
ASSEMBLY INTO PLATE
A
A
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
NO
NC
COM
LED –
LED +
SWITCH 1
SWITCH 2
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
NC
COM
NO
MAG LOCK
UB-1L LED PCB
UL Listed
NORMAL POSITION BUTTON ACTIVATED
MAGNETIC LOCK
MESSAGE LAMP
ON
OFF
OFF
ON
+
+
+
12-24 VDC Power Supply
NC
NO
NC
NO
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
OFF
ON
+
+
+
MAG LOCK
NC CONTACTS
NO CONTACTS
UB-1L LED PCB
UL Listed
12-24 VDC Power Supply
NORMAL POSITION BUTTON ACTIVATED
ON
OFF
MAGNETIC LOCK
MESSAGE LAMP
UB-1L LED PCB
NYLON WASHER
SCREW
COUNTERCLOCKWISE
CLOCKWISE
TIMER RANGE ADJUSTMENT SCREW
ADJUSTMENT RANGE - 2 TO 60 SECONDS
TIMER FACTORY SET TO MINIMUM TIME
SETTING. TO INCREASE TIME, TURN
SCREW CLOCKWISE IN 1/4 TURN
INCREMENTS. WHEN CLOSE TO DESIRED
TIME, TURN SCREW IN VERY FINE
INCREMENTS TO DESIRED SETTING.
CAUTION: OVER-TIGHTENING MAY
CAUSE DAMAGE TO TIMER.
CONNECTION AND LEAD WIRE
COLOR CODE
12
34
SCREWDRIVER
SWITCH INFORMATION
4.83 in.
(123mm)
3.22 in.
(82mm) .91 in.
(23mm)
1.47 in.
(38mm)
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
SQUEEZE TABS AND PUSH
ASSEMBLY INTO PLATE
A
A
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
POWER IN
12-30 VDC/VAC
NO
NC
COM
LED –
LED +
SWITCH 1
SWITCH 2
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWER IN
12-30 VDC/VAC
NC
COM
NO
MAG LOCK
UB-1L LED PCB
UL Listed
NORMAL POSITION BUTTON ACTIVATED
MAGNETIC LOCK
MESSAGE LAMP
ON
OFF
OFF
ON
+
+
+
12-24 VDC Power Supply
NC
NO
NC
NO
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
OFF
ON
+
+
+
MAG LOCK
NC CONTACTS
NO CONTACTS
UB-1L LED PCB
UL Listed
12-24 VDC Power Supply
NORMAL POSITION BUTTON ACTIVATED
ON
OFF
MAGNETIC LOCK
MESSAGE LAMP
UB-1L LED PCB
NYLON WASHER
SCREW
COUNTERCLOCKWISE
CLOCKWISE
TIMER RANGE ADJUSTMENT SCREW
ADJUSTMENT RANGE - 2 TO 60 SECONDS
TIMER FACTORY SET TO MINIMUM TIME
SETTING. TO INCREASE TIME, TURN
SCREW CLOCKWISE IN 1/4 TURN
INCREMENTS. WHEN CLOSE TO DESIRED
TIME, TURN SCREW IN VERY FINE
INCREMENTS TO DESIRED SETTING.
CAUTION: OVER-TIGHTENING MAY
CAUSE DAMAGE TO TIMER.
CONNECTION AND LEAD WIRE
COLOR CODE
12
34
SCREWDRIVER

- 7 -
To create your own custom label, size to fit in .48h x 2.23w as shown below.
Also available online at: www.sti-usa.com/ublabel
2.23 in.
.48 in.
6. CUSTOM LABELS
WARRANTY
ACCESSORIES
DESCRIPTION PART #
COLOR MATCH BACK BOX KIT KIT-71100A-*
* (R=Red, B=Blue, G=Green, W=White Or Y=Yellow)
CUSTOM LABEL APPLIED TO UB-1CL-*
BLANK MESSAGE PLATES * (B=Blue, G=Green, W=White Or Y=Yellow)
BUTTON REPLACEMENT LENSES: (red, green & blue) UB-1LENS
2” LENS KIT FOR UNIVERSAL BUTTON UB-2LENS
CONTACT ASSEMBLY FOR UB-1 KIT-UB-1C
24 VOLT LED
WHITE (STANDARD) KIT-E10147
RED KIT-E10145
BLUE KIT-E10141
GREEN KIT-E10143
12 VOLT LED
RED KIT-E10144
BLUE KIT-E10140
GREEN KIT-E10142
COVERS
BOPPER STOPPER STI-6518
UNIVERSAL STOPPER STI-13000 Series
STOPPER II®STI-1100 Series
– See website for complete cover details –

Printed in USA Inst. Sht. UB1PN Button JAN2011
2306 Airport Rd • Waterford, MI 48327, USA
Phone: [phone] • Fax: [phone]
[email protected] • www.sti-usa.com
Taylor House • 34 Sherwood Road • Bromsgrove, Worcestershire • B60 3DR • England
Tel: [phone] • Fax: [phone] • [email protected] • www.sti-emea.com
Warranty
Three year guarantee against breakage of polycarbonate in normal use (one
year on electro mechanical and electronic components). Electronic warranty
form at www.sti-usa.com/wc14.
WARNING: This product can expose you to chemicals including
Dichloromethane, which is known to the State of California to cause
cancer, and Bisphenol A (BPA), which is known to the State of California to
cause birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.