Stirling FS1-40DCWIFI User manual

Model Number FS1-40DCWIFI
40 cm DC Pedestal Fan
with Wi-Fi Control
po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
INSTRUCTION MANUALINSTRUCTION MANUAL
po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534

2po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
Welcome
Congratulations on choosing to buy a STIRLING®product.
All products brought to you by STIRLING®are manufactured to the highest
standards of performance and safety and, as part of our philosophy of
customer service and satisfaction, are backed by our comprehensive 2 Year
Warranty. We hope you will enjoy using your purchase for many years to come.

3
po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
Contents
02 Welcome
04 Warranty Details
05 General Safety Instructions
08 Product Overview
10 Getting Started
13 Instructions
15 Wi-Fi Control
23 Frequently Asked Questions
24 Other Useful Information
27 Repair and Refurbished Goods or Parts Notice

4po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
40 cm DC Pedestal Fan with Wi-Fi Control
Warranty Details
The product is guaranteed to be free from defects in workmanship and parts
for a period of 24 months from the date of purchase. Defects that occur within
this warranty period, under normal use and care, will be repaired, replaced
or refunded at our discretion. The benefits conferred by this warranty are
in addition to all rights and remedies in respect of the product that the
consumer has under the Competition and Consumer Act 2010 and similar
state and territory laws.
Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for
a major failure and to compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does
not amount to a major failure.
REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION

5
po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
General Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
Read this manual thoroughly before first use, even if you are familiar with this
type of product. The safety precautions enclosed herein reduce the risk of
fire, electric shock and injury when correctly adhered to. Keep the manual
in a safe place for future reference, along with the completed warranty card,
purchase receipt and carton. If applicable, pass these instructions on to the
next owner of the appliance.
Always follow basic safety precautions and accident prevention
measures when using an electrical appliance, including the following:
Electrical safety and cord handling
• Voltage: Make sure your outlet voltage and circuit frequency correspond to
the voltage stated on the rating label. If this is not the case, do not use the fan.
• Water: To protect against fire and electric shock, do not immerse the AC
adaptor, cord, plug or the fan itself in water or other liquid, or expose the
electrical connections to water. Ensure your hands are dry before handling
the plug or switching on the fan. Do not use the fan outdoors or on wet
surfaces. Protect it from liquid spills.
• Damage: Check the power cord regularly for visible damage. If the adaptor
cord is damaged, it must be replaced by the manufacturer, its authorised
service agent or appropriately qualified personnel in order to avoid a hazard.
WARNING! Do not pick up or operate the fan if the AC adaptor, cord, plug or
housing is damaged, or after it malfunctions or has been dropped or damaged
in any manner. In case of damage, contact our after sales support centre.
• Protect the adaptor and power cord:
- Do not operate the fan with the AC adaptor’s power cord coiled up;
always fully unwind.
- Do not twist or kink the cord or let it touch heated surfaces or sharp edges.
- Do not allow the cord to hang over the edge of a table or bench.
- Do not put any stress on the cord where it connects to the product.
- Never carry the fan by the cord.
- Arrange the cord away from any traffic area so no one will trip over it.
- Do not run the cord under carpeting or cover it with rugs or runners. In the
event of danger, the plug must be quickly and easily accessible.
• WARNING! No extension cord, no timer: Do not use this fan with an
extension cord, plug adaptor, external timer or separate speed control
device. Plug the AC adaptor straight into an appropriate electrical outlet.

6po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
General Safety Instructions (Cont.)
• Connection: To connect the fan to the power supply, insert the AC
connector into the socket at the back of the appliance, then insert the
power plug firmly into an appropriate electrical outlet.
• Disconnection: Unplug the fan from the power outlet when it is not in use
and before cleaning, servicing, moving or storing the appliance. Grasp the
plug and remove it from the outlet, do not pull the cord when disconnecting.
• Guard removal: Ensure the fan is disconnected from the power supply
before removing a front or rear guard (grille).
• RCD: Unless your home is already fitted with a residual current device (safe-
ty switch), we recommend installing an RCD with a rated residual operating
current not exceeding 30 mA to provide additional safety protection when
using electrical appliances. See your electrician for professional advice.
Usage conditions and restrictions
• Domestic use only: This appliance is intended for indoor household use
only. It is not suitable for commercial, industrial or outdoor use. Do not use it
for anything other than its intended purpose, and only use it as described in
this manual. Any other use may cause fire, electric shock or injury.
• No clothes drying: Do not use this fan as a dryer.
• Attachments: The use of accessory attachments not recommended by the
appliance distributor may result in fire, electric shock or personal injury.
• Usage restriction: This fan is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their
safety.
• Children: This fan is not a toy. Supervise children to ensure they do not play
with it. Close supervision is necessary when any appliance is used by or
near children.
• WARNING! Do not leave unattended during use. Always switch it off and
unplug when not in use, if left unattended and before cleaning and storing.
• Assembly: Do not attempt to operate the fan until fully assembled with all
parts. Do not use the appliance without the protective grilles (rear and front
guards). Do not attempt to force the grille in order to stop or start the fan.
• Location: Place the fan on a dry, flat, stable surface to avoid overturning.
• Keep the top clear: Do not place anything on top of fan.

7
po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
• Airflow openings: Ensure nothing is blocking the airflow outlet and air
intake grilles. Do not insert foreign objects into any opening as this may
cause electric shock and/or a fire hazard. Clean the appliance regularly to
avoid dust accumulation on opening grilles.
• WARNING! DO NOT use the fan in the following areas:
- near an open flame, a hot burner, oven or near other sources of high heat
- on a soft surface (such as carpet) or where it may tip over during use
- outdoors or in areas of high humidity without suitable ventilation (such as
in a bathroom, laundry area, near a sink, washer, pool or any source of
water)
- near curtains or drapes as they may be sucked into the fan and cause an
electrical hazard
- in areas where paint, petrol, etc. is stored and there is a risk of explosion
or fire from flammable gases, or in areas where substances are being
sprayed.
• CAUTION! Personal safety: Avoid contact with moving parts. Never
insert fingers, pencils or any other objects through the grilles when the fan
is running, as this may cause electric shock and/or a fire hazard. Keep hair
and loose clothing well away from the fan when it is in use.
• Misuse of the product can result in personal injury or damage to property.
We accept no liability for any damages or personal injury caused by
misuse of the product and/or failure to follow these instructions.
General Safety Instructions (Cont.)

8po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
Product Overview
Scope of delivery
Assembled fan
1 Guard ring
2 Front and rear guards (grilles)
3 Fan blade
4 Extension pole
5 Height adjustment knob
(at the back, not visible here)
6 LED display
7 Control panel
8 DC socket
(at the back, not visible here)
9 Base tube
10 Remote control (2x AAA
batteries packed separately)
11 Weighted base
12 AC adaptor and cord
Documentation (not shown)
Instruction manual
Quick start guide
Warranty certificate
1
2
4
NOTE: Due to continued product improvement, images and illustrations in this manual
may vary slightly from the product purchased. All images in this manual are for reference
purposes only. Parts are not necessarily pictured to scale.
3
6
7
9
11
5
8
10
12

9
po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
Product Overview (Cont.)
Control panelControl panel and remote
control buttons
13 SPEED button
14 POWER button
15 TIMER button
16 SWING button
17 MODE button
18 ON button
19 MODE button
20 SPEED + button
21 SPEED – button
22 TIMER + button
23 TIMER – button
24 SWING button
25 OFF button
Remote control
18
21
24
23
25
20
22
19
6
13
14
15
16
17

10 po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
Unpacking
• This product has been packaged to protect it against transportation damage.
Unpack the appliance and keep the original packaging carton and materials
in a safe place. It will help prevent any damage if the product needs to be
transported in the future, and you can use it to store the appliance when it
is not in use. In the event that the packaging is to be disposed of, please
recycle it where possible.
• Plastic wrapping can be a suffocation hazard for babies and young children,
so ensure all packaging materials are out of their reach and disposed of safely.
• Unwind the cord to its full length and inspect it for damage. Do not use the
appliance if the appliance or its cord have been damaged or are not working
properly. In case of damage, contact our after sales support centre for advice
on examination, repair or return of the damaged product.
• Make sure you have read and understood all instructions and warnings in
this manual. Refer to the product overview (pages 8–9) and parts illustrations
(pages 11–12) to familiarise yourself with the product and identify all parts.
Pay particular attention to the safety instructions on the previous pages.
Remote control preparation
• The fan comes with a remote control, which is powered by two AAA batteries
(supplied separately). Slide out the battery cover with your thumb on the
mark at the back of the remote control. Insert the batteries following the
polarity symbols (+/-), then replace the cover to the battery compartment.
• When replacing batteries, always replace all batteries with new ones of the
same size and type. Do not mix old and new batteries. Do not mix alkaline,
standard (carbon-zinc), or rechargeable (NiCd, NiMH) batteries. Do not open
or short-circuit batteries.
• If the remote control will not be used for a long period of time, remove the
batteries from the battery compartment to avoid leakage which can damage
the remote control.
• Assembly: Your new fan has been shipped partially assembled to reduce
wastage of packaging material, paper cartons and weight. The illustrations in
the assembly sections show how all the parts fit together.
WARNING: Electric shock hazard!
Do not plug the power supply cord into an electrical outlet
until the fan is fully assembled.
Getting Started

11
po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
Getting Started (Cont.)
Assembling the fan body and base
Using Fig. 1, above, to guide you, assemble the fan as follows:
1. Loosen the screw from the tube and connect the tube with the main body,
then fasten the screw.
2. Assemble the main body into the cover tube and connect the two pieces.
3. Remove the lock nut from the tube. Turn the base parts over, place the
silver-coloured cover on top, then place the base parts over the tube.
Affix the fan body to the base using the lock nut at the underside of the
weighted base, tightening it securely.
4. Tighten the height adjustment screw at a comfortable height for attaching
the fan head.
Main body
Screw
Extension pole
Cover tube (white metal)
Tube base
(silver-coloured cover)
Weighted stand
base and plastic
cover
Lock nut
(attached to the end of the tube)
Fig. 1

12 po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
Getting Started (Cont.)
Assembling the fan head
Using Fig. 2, below, to guide you, assemble the fan head as follows:
1. The motor shaft has the blade cap and guard nut attached. Remove
the cap by turning it clockwise. Then remove the nut by turning it
anticlockwise.
2. Place the rear guard on the front of the motor housing, lining up the two
positioning knobs on the front of the motor housing with the holes in the
rear guard. Push the guard in firmly until the two knobs protrude through
the holes. Secure the rear guard by reattaching the guard nut and turning it
clockwise to tighten.
3. Slide the blade onto the motor shaft, making sure to match the protrusions
on the shaft with the slots in the blade. Tighten the blade with the blade
cap, turning it anticlockwise to tighten it securely.
4. Test the fan by rotating the blade with your hands, making sure that there is
no contact with the nut. The fan blade should rotate freely.
5. If the decorative front plate is covered with a plastic film, remove the film.
6. The front and rear guard are held together with a guard ring, which has two
grooves, one for each of the guards. Slightly loosen the large screw at the
bottom of the ring and ensure the edge of the guard sits in the appropriate
groove, all around the rear guard. Then fit the front guard against the rear
guard and ensure that the edge sits properly in the other groove. Retighten
the screw to secure the guards together.
Your new pedestal fan is now fully assembled.
1 Front guard
2 Guard ring
3 Blade cap
4 Blade
5 Guard nut
6 Rear guard
7 Motor shaft
8 Decorative front
plate
8
Fig. 2
1 2 4 6
7
3 5

13
po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
Instructions
• Place the fan on a dry, level surface.
• Insert the appliance plug of the AC adaptor in the DC socket at the back of
the fan body. Then plug the power plug into an appropriate electrical outlet
and switch on the power to the outlet. All available settings options will be
illuminated briefly on the control panel.
• For remote control operation, please ensure the remote control contains
two AAA size batteries.
Remote control or control panel operation
This fan is equipped with 15 step speed control, 3 breeze modes, a
10 hour timer and a remote control. For your convenience, all functions can
be operated with the remote control, or with the buttons on the control panel
on the main fan body.
You can also control the fan remotely with your mobile device using the fan’s
in-built Wi-Fi module; please refer to pages 15 to 22 for instructions.
Switching on/off
Press the ON / button to switch on the fan. When first switched on, the fan
will start blowing air at the lowest fan speed (1). On subsequent uses it will start
at the previously selected fan speed.
During operation, press the OFF / button to set the fan to standby.
Selecting a fan speed
Press the SPEED+/- / SPEED button(s) to increase/decrease the fan speed in
15 steps.
Mode selection
Press the MODE button to change the fan mode through different breeze
modes.
• Normal: In this mode the fan operates at a constant speed. (The mode
indicator shows the fan icon.)
• Natural: In this mode the fan simulates a natural breeze mode by cycling
on and off, as in nature. (A palm tree indicates Natural mode.)
• Sleep: In this mode the fan simulates a soft, natural breeze suitable for
night-time use. (A half moon indicates Sleep mode.)

14 po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
Instructions (Cont.)
Fig. 3
Timer operation
Press the TIMER / TIMER +/- button(s) to set the timer in half-hour increments
up to a maximum of 10 hours. The set time (number of hours) will appear on
the LED display. After the timer expires, the fan will automatically shut off.
Oscillation
Press the SWING button to activate the oscillation function for left/right
breeze distribution (Fig. 3). To stop oscillation, press the button again when
the fan head is in the desired position.
Tilting the fan head
The fan head can be tilted so that the breeze is targeted at an angle.
To tilt the fan head, make sure the fan is disconnected from the power supply.
Grip the motor housing and carefully tilt the fan head downward until it
reaches the desired angle. Only a soft touch is needed to adjust the fan head
position.
CAUTION: Do not tilt back the fan head further than it is intended to go.
Doing so will damage the unit.

15
po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
Wi-Fi Control
This STIRLING 40 cm DC pedestal fan features Wi-Fi technology, which
enables you to control the appliance remotely from wherever you are —
at work, at play or on the go — so that on your arrival at home the room
temperature is comfortable. The DC pedestal fan works in conjunction with
your mobile device, using your home Wi-Fi network router to communicate with
the fan.
Controlling the DC pedestal fan remotely is very easy. You will need:
• an Android smartphone or an Apple iPhone
• an internet connection at your home
• a Wi-Fi network router set up at home.
You must also have our STIRLING App installed or updated on your
smartphone or iPhone. This app is available from Google Play Store or Apple
App Store.
Initial set-up
Upon installation of your new DC pedestal fan, or when you have changed your
mobile device or wireless router, you will have to set up the communication
channel between the devices. In order to do this, make sure you have the
STIRLING App installed or updated on your mobile device, your Wi-Fi router is
switched on and your mobile device connected to your home Wi-Fi network.
• On your mobile device, tap on the [STIRLING ] app (Fig. WF1). It will
open and take you to the Login Page (Fig. WF2).
Fig. WF1 Fig. WF2

16 po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
Wi-Fi Control (Cont.)
• Before you log in, please tap [ Register ] and register your account using
your email account (Fig. WF3, WF4).
Fig. WF4
Fig. WF3
NOTE: If you do not want to create an account, you may also continue as a
guest. To log in as a guest, tap [ Try now ] (Fig. WF5), then tap [ Continue ]
(WF6). (Some app features may not be available without log in.)
Fig. WF5 Fig. WF6

17
po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
IMPORTANT!
Before you can control your fan remotely with its
in-built Wi-Fi technology, you must reset the Wi-Fi
module. To do so, proceed as follows:
• Unplug the fan for 10 seconds, then
reconnect the power supply.
• To reset the Wi-Fi module, press the
SWING button on the fan’s control panel
and hold it for 5 seconds until it beeps.
• When the Wi-Fi indicator on the control panel
is blinking rapidly (WF10), the Wi-Fi module
is ready for configuration with your mobile
phone.
Fig. WF10
- -
Fig. WF8
Fig. WF7
• Once you have registered and entered your email address, tap [ Get
Verification Code ] and an email will be sent directly to the email account
that you entered when registering. Enter this verification code.
• Now you have to enter your password and tap [ Done ] (Fig. WF7).
• You will now enter the main device list (Fig. WF8). Tap [ + ] or [ Add
Device ] and add your device from the product list (Fig. WF9).
Wi-Fi Control (Cont.)
Fig. WF9

18 po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
• On completion, you
can name your device.
Tap [ Done ].
• You will return to the
Device list and your
device will be shown
(Fig. WF14).
• Click on the device
name and it will take
you to the main control
page (Fig. WF15).
Wi-Fi Control (Cont.)
Fig. WF14
Fig. WF11 Fig. WF12
• On your mobile device, enter your Wi-Fi name and password, then
tap [ Next ] (WF11). Tap [ Confirm indicator rapidly blinks ], then tap
[ Next ] (WF12). The message “Adding device” will appear on the screen
(Fig. WF13).
Fig. WF13
Fig. WF15

19
po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
Wi-Fi Control (Cont.)
• If the device is not responding and you get the following message, you can
try to switch the pairing mode (Fig. WF16). Click [ Switch Pairing Mode ]
and then follow the prompts (WF 17, WF18).
Fig. WF16 Fig. WF17 Fig. WF18
• After you have
confirmed your Wi-Fi
network and password,
connect your mobile
phone to the device’s
hotspot (WF19, WF20),
then go back to the app
and continue to add the
device.
Fig. WF19 Fig. WF20

20 po.org
MODEL: FS1-40DCWIFI PRODUCT CODE: 706541 10/2021
AFTER SALES SUPPORT info@tem
AUS 1300 112 534 po.org
AFTER SALES SUPPORT info@tem
AUS 1300 112 534
Wi-Fi Control (Cont.)
Device sharing
• The device only recognises ONE registered user. But you can share
access to the device with other members of your household if they have
the STIRLING app installed and updated on their phone. To share the
device, proceed as follows:
Fig. WF23
Fig. WF21 Fig. WF22
Fig. WF24
• On the device’s
main control
page, click the
edit symbol in the
top right corner
(WF21). Then
select [ Share
Device ] (WF22)
and follow the
prompts (WF23,
WF24).