STORZ & BICKEL Mighty User manual

INSTRUCTIONS FOR USE
Read carefully before using the device
and save these instructions.

32
Table of Contents ....................................................................... Page
1. Product Overview, Scope of Delivery .............................................. 4
2. Explanation of Symbols, Safety Recommendations ................... 6
2.1. Explanation of Symbols............................................................. 6
2.2. Safety Recommendations ........................................................ 8
3. Intended Use ........................................................................................ 10
4. Overview of Plants ............................................................................. 11
5. Factors Inuencing Vaporization .................................................... 12
6. The MIGHTY Vaporizer ..................................................................... 12
6.1. Unpacking................................................................................... 12
6.2. Power Connection ....................................................................13
6.3. Application and Operation ......................................................13
6.4. Storage........................................................................................13
6.5. In Case of Problems ................................................................. 14
6.6. Possible Faults / Troubleshooting ........................................14
6.7. Disposal.......................................................................................14
7. Commissioning and Operation ....................................................... 15
7.1. Charging the Battery .............................................................. 15
7.2. Heating Up ................................................................................ 16
7.3. Temperature Setting .............................................................. 17
7.4. Reset to Default Settings ...................................................... 18
7.5. Default Settings ....................................................................... 18
8. Filling the Filling Chamber ................................................................ 19
8.1. Filling Aid ................................................................................... 20
8.2. Filling the Filling Chamber
using the Filling Aid ................................................................. 21
INSTRUCTIONS FOR USE ENGLISH
Table of Contents ....................................................................... Page
9. Application ........................................................................................... 22
10. Disassembling, Cleaning and Assembling ................................... 23
10.1. Disassembling and Reassembling
the MIGHTY Cooling Unit ...................................................... 24
10.2. Cleaning the MIGHTY Cooling Unit .................................... 26
10.3. Removal of the Lower Filling Chamber Screen ................ 26
11. Accessories ......................................................................................... 27
11.1. Dosing Capsules and Magazin................................................ 27
11.2. Disposable Lip Piece for Hygienic Use ................................ 30
12. Technical Specications ................................................................... 31
13. CE Declaration of Conformity .......................................................... 32
14. Warranty, Liability ............................................................................... 33
14.1. Warranty......................................................................................33
14.2. Liability ........................................................................................33
14.3. Copyright.....................................................................................34
INSTRUCTIONS FOR USE ENGLISH

Dosing Capsule
54
1. PRODUCT OVERVIEW MIGHTY VAPORIZER
Power
Adapter
Herb Mill
Filling Aid
Cleaning Brush
3 pcs. Spare Screens
MIGHTY
Vaporizer
Drip Pad
Instructions
for Use
Scope of Delivery:
1 Set of Spare
Seal Rings (one Seal Ring
each)
(optional accessory: 12 Volt Car Charger)
Please check whether all components have been included. If not, please inform the
Storz & Bickel Service Center.
In the case of technical problems, questions about the device, warranty claims and
disposal of the device, customers in the US and Canada should contact the following
address:
Storz & Bickel America, Inc.
1078 60th Street, Suite A · Oakland, CA 94608
All other customers should contact this address:
Storz & Bickel GmbH & Co. KG
In Grubenäcker 5-9 · 78532 Tuttlingen, Germany
1. PRODUCT OVERVIEW MIGHTY VAPORIZER
ON/OFF Switch
Type Label
(on the rear)
Minus Temperature Button Plus Temperature Button
Actual Temperature Display
Charging Socket
Filling Chamber
Mouthpiece
Cooling Unit
Filling Chamber Tool
(under the Type Label)
Set Temperature
Display
Battery Charging Display
MIGHTY Vaporizer functional elements:

76
2.1. Explanation of Symbols
Read the following safety
recommendations thorough-
ly and carefully before using
the device.
These Instructions for Use are a
signicant part of the Vaporizer and
power adapter and must be provided
to the user.
The instructions given in these In-
structions for Use must be strictly
observed as they are extremely im-
portant to ensure safety during in-
stallation, use and maintenance of
the Vaporizer and power adapter.
Please keep this brochure in a safe
place for future reference.
You may download the current In-
structions for Use for the MIGHTY
on www.storz-bickel.com.
2. SAFETY RECOMMENDATIONS
Please follow these instructions carefully!
Safety recommendations!
In order to avoid injuries to persons and damage to the equipment,
it is mandatory to observe instructions marked with this symbol.
Note/Tip!
This symbol always gives you technical information or useful tips
regarding the Vaporizer.
EU conformity symbol:
The manufacturer conrms with this symbol the compliance of the
product with the applicable European directives and standards.
The device was introduced after 13 August 2005. It may not be
disposed of in normal household waste. The X on the trash can
indicates the necessity of disposing of this device separately. The
device contains a built-in rechargeable lithium-ion battery that must
be discharged before disposal.
Symbol for the manufacturer - the manufacturer‘s name and
address are next to the symbol
2. SAFETY RECOMMENDATIONS
Safety tested and production monitored by TUEV SUED according
to EN 60335-1, UL 499 and CAN/CSA-22.2 No. 64-M91.
Caution! Hot surfaces!
Do not touch metal parts!
Protect from direct sunlight.
Protect against moisture and humidity.
UL Recognized Component Mark: This symbol indicates that the
corresponding devices are listed by UL
The following symbols relate to the power adapter.
Restriction on the use of certain hazardous substances in electrical
and electronic equipment
Equipment with this symbol may only be used in the house
(dry surroundings).
Eciency Level 5
Eciency of power adapter
Safety Category II device
DC (direct current)

98
2.2. Safety Recommendations
The packaging material (plastic
bags, boxes etc.) must be kept out
of the reach of children as it is a
potential source of danger.
Check the packaging and the hous-
ing of the Vaporizer. In case the
housing appears to be damaged,
please send back the Vaporizer
immediately. In any event, avoid
contact of any kind with leakage
liquid.
People who require assistance
must be supervised constantly
during application. Such persons
often underestimate the hazards
involved (e.g. strangulation with the
power adapter cord), thus resulting
in a risk of injury.
The device contains small parts.
which can block the respiratory
tract and lead to choking. There-
fore, make sure that you always
keep the Vaporizer and the acces-
sories out of the reach of babies
and infants.
When charging the battery, only
use the power adapter supplied
with the Vaporizer or the 12 Volt
car charger available as an acces-
sory from Storz & Bickel. The use
of charging devices from other
sources can damage the battery.
If you have any concerns, ask a
specialist to check whether the
electrical system is in accordance
with the local safety regulations.
If there are any problems during
operation, immediately pull out
the power adapter from the
socket.
The power adapter cord must be
unwound over its entire length
(avoid rolling up and overlapping
the cord). It must not be exposed
to any impacts and must be kept
out of the reach of children. Also,
it must not be kept near liquids or
sources of heat and must not be
damaged. Do not wind the power
adapter cord tightly, nor pull it over
sharp edges and never crush or
kink it. If the power adapter cord
is damaged, please contact our
Service Center to have it replaced.
Never try to repair a power
adapter cord yourself!
The use of multiple sockets and/
or extension cables is not recom-
mended. However, if this is abso-
lutely necessary, only products
with a quality certificate (such
as UL, IMQ, VDE, +S etc.) may
be used, provided the specified
power exceeds the power required
(A=Ampere) by the devices that
are connected.
After use, the Vaporizer must be
placed on a stable, flat surface.
To be used only at a sufficient
distance away from heat sources
(ovens, stoves, fireplaces), and
in locations where the ambient
temperature cannot drop below
+5°C (+41°F). Store the Vaporizer
2. SAFETY RECOMMENDATIONS
and power adapter in a dry place
protected against the effects of
weather and out of the reach of
children or unqualified persons. It
cannot be used in damp locations
(such as bathrooms, etc.)
Do not operate the Vaporizer close
to flammable objects such as
curtains, tablecloths, or paper.
Keep the Vaporizer and power
adapter away from pets (e.g.
hamsters, mice) and other animals
which could damage the insulation
of the power adapter cord.
The Vaporizer and power adapter
may not be repaired by the cus-
tomer. Incorrectly performed
repairs without the use of original
spare parts can prove dangerous
to the user.
Danger to life when opening the
power adapter as live components
and connections are exposed.
The Vaporizer must never be
repaired or transported when the
power adapter is plugged in.
The Vaporizer and power adapter
must never be operated when the
power adapter cord is faulty.
Do not put any objects into the
openings of the device.
Do not leave the Vaporizer unat-
tended while it is being operated.
After use, switch off the heater.
The ventilation slots and the hot
air outlet of the Vaporizer may not
be closed, obstructed, or blocked
while the device is being used, nor
while it is cooling down.
Caution! Hot surfaces!
The Filling Chamber is made of
metal; do not touch it when it is
hot.
Before cleaning, disconnect the
power adapter from the socket.
The Vaporizer and the power
adapter should be cleaned only
with a dry cloth - or a damp cloth
if absolutely necessary. Never im-
merse the Vaporizer or the power
adapter in water or any other liquid,
nor clean it with direct jets of water
or steam.
The Vaporizer and the power
adapter must not be used in damp
or wet conditions.
Do not expose the Vaporizer or the
power adapter to rain. Do not use
in the bathroom or above water.
Never touch the Vaporizer or power
adapter with wet or damp parts of
the body.
Never operate the Vaporizer or
power adapter when it is wet
or damp. If the Vaporizer or the
power adapter gets wet, it must be
checked by our Service Center for
damage to electrical components.
Do not use in an atmosphere with
risk of explosion or ignition.
2. SAFETY RECOMMENDATIONS

1110
2. SAFETY RECOMMENDATIONS
Never allow the Vaporizer or the
power adapter to be used by chil-
dren or unqualified persons.
Only use original Storz & Bickel
accessories and spare parts.
3. INTENDED USE
The MIGHTY Vaporizer releases fra-
grances or aromas from the herbs
and other plant materials listed below.
These aromatic substances are re-
leased through vaporization by heated
air, and may be directly inhaled.
The device may only be used with the
recommended vaporizing media. The
use of other substances can present a
health risk.
The MIGHTY Vaporizer is not FDA ap-
proved.
4. OVERVIEW OF PLANTS
Portion of the Temperature-
Plant name Botanical name plant used setting
Eucalyptus Eucalyptus globulus the leaves 130°C (266°F)
Hops Humulus lupulus the cones 154°C (309°F)
Chamomile Matriarca chamomilla the blossoms 190°C (374°F)
Lavender Lavandula angustifolia the blossoms 130°C (266°F)
Lemon balm Melissa ocinalis the leaves 142°C (288°F)
Sage Salvia ocinalis the leaves 190°C (374°F)
Thyme Thymus vulgaris the herb 190°C (374°F)
Below is an overview of the plants that
are suitable for vaporization in the
MIGHTY Vaporizer.
The aromas and fragrances from the
plant materials listed below may be
vaporized.
Any other use is inappropriate and po-
tentially dangerous.
It is important to observe the following
instructions in order to set the MIGHTY
Vaporizer with the plant material in the
best possible way for your personal re-
quirements.
The MIGHTY Vaporizer is not FDA ap-
proved.
WARNING:
Please consult your doctor
or pharmacist if you have any
medical concerns. It is possible that
some plants may cause allergic reac-
tions for the user. If this occurs, it is
urgently recommended to refrain from
further use of such plants.
Only use the plant parts which are
found in this list and which have been
veried according to the regulations
of the European or any other pharma-
copoeia with regard to genuineness,
purity and pathogenic germs. You can
purchase such plants or plant parts in
pharmacies.
The manufacturer is not re-
sponsible for any damage or
personal injury caused by in-
appropriate, incorrect or irresponsi-
ble use.

1312
5. FACTORS INFLUENCING VAPORIZATION
The amount of aromas and fragrances
released can be inuenced by the fol-
lowing factors:
1. Quality: The amount of aroma or
fragrance contained in the respec-
tive plant material that can be va-
porized.
2. Quantity: The amount of vaporiza-
tion material in the Filling Chamber.
3. Surface: The ner the plant is
ground, the greater the surface and
the more aromas and fragrances
can be released during the vapori-
zation cycle.
4. Temperature: The higher the tem-
peratures, the more aromas and
fragrances will be released at once.
Please note: Increasing the tempera-
ture should be the last resort, because
plant material tastes more roasted
when using higher temperature.
Since the plant ingredients are re-
leased in a gentle manner, the vapori-
zation cycle may be repeated with the
same contents in the Filling Chamber.
Depending on the four factors de-
scribed above, the Filling Chamber
contents may be reused multiple times
until the aromas and fragrances are
released completely.
If no more vapor is produced at the
highest temperature, then the vapori-
zation material is completely exhaust-
ed and must be replaced with new ma-
terial. However, for the best aroma
results it is advisable to replace the
vaporization material before this point.
6. THE MIGHTY VAPORIZER
6.1. Unpacking
The box contains all components as
well as the Instructions for Use. Keep
the Instructions for Use for future ref-
erence.
Remove the Vaporizer and the acces-
sories from the box. Immediately after
unpacking, check whether the Vapor-
izer, the accessories, the power adapt-
er and the device plug are all included
in the delivery and work properly. If
you notice any defects, inform the
seller or the delivery agent immedi-
ately.
The packing material (plastic
bags, boxes etc.) must be kept
out of the reach of children as
it is a potential source of danger.
Please dispose of the packing mate-
rial in a proper and environmentally
friendly manner.
We recommend keeping the original
packaging in case it is required later
(transpor t, Storz & Bickel Service Cent-
er etc.).
6. THE MIGHTY VAPORIZER
6.2. Power Connection
Before connecting up the Vaporizer,
make sure that the information given
on the power adapter type label corre-
sponds to the local power supply volt-
age.
All parts of the electrical system must
comply with currently applicable o-
cial regulations.
Place the heated Vaporizer only on a
hard, stable surface, and not on any
soft or heat-sensitive material.
Take care that the power adapter cord
cannot be damaged through kinking,
crushing or pulling.
Improper installation may lead
to personal injury or material
damages, for which the manu-
facturer cannot be held responsible.
6.3. Application and Operation
This Vaporizer was developed
for vaporizing the plant materi-
als listed in the plant overview.
Any other use is inappropriate and po-
tentially dangerous.
The user should always follow the in-
structions listed here for use and main-
tenance.
If you have any concerns, or if there are
any problems immediately switch off
the Vaporizer and pull the power adapt-
er cord, if used, from the socket. Do not
try to remedy the defect yourself. Con-
tact our Service Center directly.
After using the Vaporizer and power
adapter, allow them to cool down be-
fore placing them in storage.
6.4. Storage
Store the Vaporizer and the power
adapter in a dry place protected
against the effects of weather and out
of the reach of children or unqualied
persons.
6.5. In Case of Problems
If the power adapter has been in use,
unplug it at the socket and ensure that
no one can connect the Vaporizer to
the mains supply again without this
being noticed.
Before any maintenance work is done,
the Vaporizer has to be switched off
and the power adapter unplugged
from the power supply.
Put the Vaporizer in the original pack-
aging, or pack it properly in other pack-
ing material, and send it to our Service
Center.

1514
If the preceding tips do not
yield the desired results, or for
any other defects or problems
not mentioned here, please unplug the
power adapter and contact our Service
Center immediately.
Do not open the Vaporizer or
the power adapter! Without
special tools and specialized
knowledge, any attempt to open either
of these devices will cause damage to
them. Such an attempt will invalidate
the warranty claim.
6. THE MIGHTY VAPORIZER
Do not try to remedy the defect your-
self. Contact our Service Center direct-
ly.
6.7. Disposal
If the Vaporizer or the power adapter
has been irreparably damaged after
the warranty period, please do not sim-
ply throw them away. As they are made
of high quality, completely recycla-
ble component parts, they should be
brought to a material recycling center
in your neighbourhood or sent to our
Service Center for disposal.
6.6. Possible Faults / Troubleshooting
Problem Possible Cause/Remedy
MIGHTY cannot be
switched on.
Please ensure that the MIGHTY’s battery is charged or
the Vaporizer is connected via the power adapter to a
functioning mains socket. If the Vaporizer still does not
work, then the device is faulty. In this case, disconnect
from the mains without delay and get in touch immedi-
ately with our Service Center.
The display of the
MIGHTY
shows: ERR 001.
Battery temperature is too high. Allow the Vaporizer to
cool down.
The display of the
MIGHTY
shows: ERR 002.
Battery temperature is too low. Warm up the Vaporizer.
The display of the
MIGHTY
shows: ERR 003.
The power adapter is not suitable. Please use an origi-
nal Storz & Bickel power adapter or 12 Volt car charger.
The display of the
MIGHTY
shows: ERR 004.
The Vaporizer is faulty. In this case, disconnect from
the mains without delay and get in touch immediately
with our Service Center.
7. COMMISSIONING AND OPERATION
Do not leave the device unat-
tended during operation.
Place the MIGHTY Vaporizer
only on a hard, heat-resistant, at, sta-
ble surface, never on soft surfaces or
ammable material. Check whether
the power adapter supply voltage cor-
responds to the voltage rating listed on
the power adapter. The power adapter
cord and power adapter must be in
perfect condition. Connect the power
adapter only to a properly installed
socket.
The manufacturer will not bear any
responsibility whatsoever if this acci-
dent prevention measure is not taken.
To completely disconnect from the
mains power supply, please unplug the
power adapter from the mains socket.
7.1. Charging the Battery
Explanation of the battery charging
display:
The battery charging display shows a
battery symbol with six elds indicat-
ing the charging status. If the battery is
almost discharged, the battery frame
starts to ash; if fully charged, the
frame and all six elds are visible.
The number of status elds visible
depends on the extent of the battery
charge.
Battery charging display
Check the housings of the Va-
porizer and the power adapter
for signs of damage each time
before using or charing. The Vaporizer
may not be charged and neither Vapor-
izer nor power adapter used if these
are damaged.
The battery charge of the new prod-
uct has a level of up to 80%. Fully
charge before using for the rst time.
The charging time for the battery de-
pends on how old it is and how high
the charge is on starting; it takes about
two hours if the battery is completely
discharged.
Connect the power adapter to the
charging socket of the Vaporizer and
then plug into a suitable power socket.
Note: When the power adapter is
plugged into the mains, the display
lights up for a moment and the Vapor-
izer vibrates for a short time. This is a
functional check and indicates that the
charging operation has started.
The battery charging display lights up
and starts to ash, i.e. the battery is
being charged. As soon as the battery
is fully charged, the battery charging
display stops ashing and indicates
the charge level (full = all six elds).
Once the charging operation is com-
plete, rst disconnect the power
adapter from the mains socket and
then unplug from the Vaporizer.

Minus temperature button
Plus temperature button
Actual temperature displaySet temperature display
(displayed blinking:
booster temperature)
Battery charging display
1716
Connecting the Vaporizer using the power
adapter or the 12 Volt car charger
7. COMMISSIONING AND OPERATION
The battery can also be
charged via the optional 12
Volt car charger. Connect the
12 Volt car charger to the power socket
of the Vaporizer and then plug into the
cigarette lighter or suitable 12 V sock-
et. Charge and complete the operation
in the same way as with the power
adapter (Chapter 7.1. “Charging the
Battery”, page 15).
Batteries are specially assem-
bled consumable items that
can only be replaced by Storz
& Bickel when the MIGHTY Vaporizer
is sent in to them.
Any attempt by the customer to re-
place the battery by him/herself is
potentially dangerous and leads to
loss of any claims under the warranty
and exempts Storz & Bickel from any
liability.
Mains Operation
The MIGHTY Vaporizer can also be
operated with the power adapter, even
when the batteries are completely
discharged. Proceed as described in
Chapter 7.1. “Charging the Battery”,
page 15 and then connect up the
Vaporizer.
Automatic Switching Off
The automatic switching off is used to
save battery capacity so that the Va-
porizer can be used as long as possible
without charging.
The device switches off automati-
cally two minutes after the last press
of a button or the last application. The
switching off of the Vaporizer is indi-
cated by a short vibration.
A short press of the ON/OFF
switch during operation can
reset the automatic switching-
off to two minutes.
7.2. Heating Up
The MIGHTY Vaporizer provides two
temperature levels that are set in the
factory: The basic temperature at
180°C (356°F) and the booster tem-
perature at 195°C (383°F).
Switch on the device (heating up the
Vaporizer with full Filling Chamber and
Cooling Unit mounted is recommend-
ed). To do this, press the orange ON/
OFF switch for at least half a second.
The Vaporizer responds with a short
7. COMMISSIONING AND OPERATION
vibration. The vibration does not take
place if there is a fault.
The display signals that heating is in
progress by showing the set and actual
temperatures. Set the desired temper-
ature using the temperature buttons to
the left and right of the set temperature
display. Heating up the heat exchanger
can take up to two minutes, depend-
ing on the set temperature and battery
charge level. Once the set temperature
The temperature can be set between
40°C and 210°C (104°F and 410°F)
(see Chapter 4. “Overview of Plants”,
page 11).
When you press the plus button, the
set value is increased, and when you
press the minus button, the set value is
decreased. When you briey tap on the
plus or minus button, the set values are
increased or decreased respectively in
1-degree increments. If you keep the
7.3. Temperature Setting
is reached, this is signaled by a short
double vibration.
If the basic temperature can no longer
provide adequate evaporation, the
booster temperature can be activated
by means of a double-click on the
orange-colored ON/OFF switch. Once
the booster temperature is reached,
this is signaled by a short double vibra-
tion and a blinking Set Temperature
display.
plus or minus button pressed, the set
values start running continuously in
the corresponding direction.
The booster temperature can be ad-
justed in the same way. However, it
cannot be set lower than the previous
set temperature.
The current acutal temperature can be
read from the upper line of the display.

1918
7. COMMISSIONING AND OPERATION
Fahrenheit/Celsius
If you simultaneously tap on the plus
button and the minus button, the dis-
play changes from degree Celsius to
degree Fahrenheit and vice versa.
7.4. Reset to Default Settings
It is possible to reset settings. The
reset is made by pressing the ON/
OFF button for ten seconds while the
MIGHTY Vaporizer is switched on. If
the ON/OFF button has been pressed
for ten seconds, the signaling of the
reset is made by vibration. The basic
temperature is reset to 180°C (356°F)
and the booster temperature is reset to
195°C (383°F).
7.5. Default Settings
Basic temperature: 180°C (356°F)
Booster temperature:
additional 15°C (27°F),
so corresponding to 195°C (383°F)
8. FILLING THE FILLING CHAMBER
Turn the Cooling Unit with a 90° rota-
tion counterclockwise in order to re-
move it from the Vaporizer.
Always ll the Filling Chamber com-
pletely up to the plastic rim with ground
plant material. Do not compress the
Removal of Cooling Unit (with Mouthpiece)
Filling Chamber properly lled
Filling Chamber partially lled, with Drip Pad
placed on top
plant material too much so that the
airow is not unnecessarily impeded.
Remove any excess plant material left
around the lling aperture so that it is
clean and allows the Cooling Unit to be
tted.
If the Filling Chamber is only
partially lled, then the vapori-
zation material may shift
around; the hot air then bypasses the
vaporization material, so that no va-
porization can occur.
If the Filling Chamber is not to be lled
completely, it is recomended to place
the included Drip Pad over the herbs,
and then mount the Cooling Unit on the
Vaporizer.

Upper
Cap
Plug
Lower
Cap
Bowl
2120
8. FILLING THE FILLING CHAMBER
Filled Filling Aid
(upper cap removed)
Take care that the Screens are
not obstructed with plant ma-
terial. To guarantee optimal
results, we recommend cleaning the
Screens after each vaporization cycle
with the enclosed Cleaning Brush.
The upper Screen especially can be-
come clogged with plant material and
so make inhaling dicult. In this case,
remove the Screen as described in
Chapter 10. “Disassembling, cleaning
and assembling”, page 23 and clean
or insert a new Screen.
Then re-mount the Cooling Unit by ro-
tating it clockwise through 90°.
As soon as the lower Filling Chamber
Screen is clogged or shows depos-
its, a cleaning of the Filling Chamber
is needed. For that, please rstly re-
move the lower Screen as described
in Chapter 10.3. “Removal of the lower
Filling Chamber Screen”, page 26
and clean the Filling Chamber with
a cotton stick that has been soaked
in alcohol. Please make sure that no
alcohol drops into the inner of the de-
vice. After cleaning, a new Screen is to
be inserted.
8.1. Filling Aid
The Filling Aid supplied with the unit
makes lling the Filling Chamber an
easy and clean operation and serves
as a magazine for transporting and
storing plant material already ground
in the Herb Mill.
To ll the Filling Aid, remove the up-
per cap and ll the bowl incl. plug with
ground plant material. Replace the up-
per cap and close it.
8.2. Filling the Filling Chamber using
the Filling Aid
Remove the Cooling Unit from the Va-
porizer and remove any residues that
may be in the Filling Chamber. The
Filling Chamber Tool can be a help in
doing this.
Remove the lower cap of the Filling Aid
by turning counterclockwise. Place the
Filling Aid on the Vaporizer and attach
by turning it clockwise. Remove the
upper cap from the Filling Aid. Pull the
plug and use it to ll a portion of plant
material through the central opening
into the Filling Chamber.
Make sure that the Filling
Chamber is not overlled (see
Chapter 8. “Filling the Filling
Chamber”, page 19).
Fill the Filling Aid to the lower rim
(see the two following drawings)!
Overlling leads to clogging of the
Screens and can make inhaling more
dicult.
Then re-insert the plug into the central
opening and screw on the upper cap of
the Filling Aid.
Unscrew the Filling Aid with a 90° rota-
tion and screw on the lower cap again.
Then re-mount the Cooling Unit by ro-
tating it clockwise through 90°.
Filling the Filling Chamber with the Filling Aid
8. FILLING THE FILLING CHAMBER
The lower rim of the Filling Aid must be above
the top level of the plant material

Cap Lock
Mouthpiece
Cooling Unit Cap
Base Seal Ring
(small)
Base Seal Ring
(large)
Upper Screen
(coarse mesh width)
Cooling Unit Base
Mouthpiece Seal Ring
2322
9. APPLICATION
Using the MIGHTY Vaporizer
Mount the Cooling Unit on the Vaporiz-
er and heat up. This ensures that both
the Filling Chamber and the material
to be vaporized are preheated and the
vaporizing can begin as soon as the
heating process is completed.
Caution! Hot surface!
After using the MIGHTY Va-
porizer, do not touch the Fill-
ing Chamber until it has cooled down
again.
Once the Vaporizer has reached the
set temperature (set and actual tem-
peratures are the same, also signaled
by a short double vibration) and the
Mouthpiece is folded out, the inhaling
process can then begin.
Please note the following about va-
por generation: the more intense the
vapors, the greater the impairment of
the flavor.
A very high intensity (density)
of the vapor can lead to irrita-
tion of the respiratory passag-
es from the concentration of the aro-
mas and fragrances.
In this case, the temperature should
be lowered, so that the intensity of the
vapors is reduced.
The device is not to be used, if
the user has respiratory tract
or lung conditions. Depending
on the density, the vapor could irritate
respiratory tracts or lungs, which can
lead to coughing.
Inhale only half of air you can
normally manage. Hold your
breath for a few seconds and
exhale slowly. It is advisable to deliber-
ately concentrate on your breathing
process.
After vaporization, turn off the
MIGHTY Vaporizer. To do this, press
the orange ON/OFF switch for at least
half a second. The Vaporizer acknowl-
edges the switching off with a short
vibration.
Pull the power adapter (if it is used)
from the socket and disconnect from
the Vaporizer.
Allow the Vaporizer and the power
adapter to cool down before they are
packed away.
10. DISASSEMBLING, CLEANING AND ASSEMBLING
When the vapors are cooled, it is in-
evitable that a small fraction is con-
densed on the internal surfaces of the
Cooling Unit.
The component parts of the Cooling
Unit, including the Mouthpiece must
be thoroughly cleaned on a regular ba-
sis to guarantee proper operation and
pure avor.
For hygienic reasons, it is also neces-
sary to clean these components when
the Vaporizer is to be used by a differ-
ent person.
The condensate can be sticky.
The Cooling Unit can be dis-
mantled more easily when it
rst warmed up.
Product Overview of the MIGHTY Cooling Unit
The Cooling Unit consists of:
Take the Mouthpiece between the lips,
and inhale slowly and evenly for sev-
eral seconds.

2524
10. DISASSEMBLING, CLEANING AND ASSEMBLING
10.1. Disassembling and Reassem-
bling the MIGHTY Cooling Unit
Turn the Cooling Unit with a 90° rota-
tion counterclockwise in order to re-
move it from the Vaporizer.
Pull out the Mouthpiece from the Cool-
ing Unit cap, rotate slightly back and
forth while doing this, and pull off the
Mouthpiece Seal Ring.
Pulling the Mouthpiece from the Cooling Unit
Cap
Opening the Cap Lock
Open the Cap Lock by pulling it rear-
wards.
Remove the Cap Lock from the cap by
pulling up at one side.
Only if you intend to immerse
the Cooling Unit into alcohol
(ethanol) is it necessary to re-
move the Cap Lock. Extended contact
with alcohol can lead to whitening of
the Cap Lock Label or disintegration of
the glue.
Removal of the Cap Lock
Separate the Cooling Unit Cap from
the Cooling Unit Base by pulling off the
cap upwards.
Removal of the large Base Seal Ring
Remove the large and small Base Seal
Rings. Lever out the large Seal Ring
from the recess in the notch using the
Filling Chamber Tool.
Reassemble in reverse order.
When assembling, make sure
that Seal Rings are properly
seated. The Mouthpiece Seal
Ring, especially, must sit completely in
the cap and be no longer visible.
The upper Screen must be inserted
carefully into the groove provided. Dis-
regarding this may allow plant parti-
cles to enter the Cooling Unit, so block-
ing this or be inhaled.
Pressing out the upper Screen
Push the upper Screen downwards out
of the Filling Chamber Cap from above
by using the Filling Chamber Tool sup-
plied.
10. DISASSEMBLING, CLEANING AND ASSEMBLING
Pull the Cooling Unit
Cap from the Cooling Unit Base

2726
Do not immerse any plastic
components in alcohol or eth-
anol for longer than an hour.
Extended contact with alcohol or etha-
nol can lead to discoloration or embrit-
tlement of plastic parts.
Before assembling allow all compo-
nent parts to dry properly.
After cleaning, check all component
parts for surface damage, tears, sof-
tening or hardening, impurities, distor-
tion and discoloration and set dam-
aged component parts aside.
Warning! Alcohol (ethanol) is
ammable and may easily ig-
nite.
Sets of new Cooling Units may
be ordered from www.storz-
bickel.com.
10.3. Removal of the Lower Filling
Chamber Screen
Remove the lower Filling Chamber
Screen using the Filling Chamber
Tool by pushing in along the indenta-
tion of the Filling Chamber. In this way
the Screen arches and detaches itself
from the notch.
Inserting a new Screen: It is easier to
insert the Screen if it was previously
curved and inserted with the curved
side facing up. Using the Filling Cham-
ber Tool, you can press the screen at
so that the edges of the screen seat
into the groove at the bottom of the
Filling Chamber.
10.2.Cleaning the MIGHTY Cooling
Unit
The Cooling Unit can be disassem-
bled for cleaning purposes and then
assembled again (see Chapter 10.1.
“Disassembling and Reassembling the
MIGHTY Cooling Unit”, page 24).
The Cleaning Brush, cotton swabs and
paper or cotton towels may be used for
cleaning. As solvent, we recommend
alcohol (ethanol) or warm water with
wash-up liquid.
For optimal airow, please ensure the
Cooling Unit and Mouthpiece are clean
and free from debris blockage.
Manual cleaning of the disassembled Cooling
Unit
10. DISASSEMBLING, CLEANING AND ASSEMBLING 11. ACCESSORIES
11.1. Dosing Capsules and Magazin
Dosing Capsules with Magazine
With the Dosing Capsules, which are
available as accessories, you can ll
ground plant material or aromatic oils
using the Drip Pads into the Dosing
Capsules in advance and store them
in the Magazine. This facilitates the
handling.
Filling the Dosing Capsules with
ground Plant Material
The plant material has to be ground
with the included Herb Mill rst.
The Dosing Capsules can be lled with
ground plant material per Capsule and
be stored in the Magazine as a reserve.
Dosing Capsule with removed cap
Grind the plant material and ll the
Dosing Capsule by using the Magazine
Cap (funnel).
Dosing Capsule while being lled with
Magazin Cap (funnel)
Attach the cap onto the Dosing Cap-
sule. Repeat the lling process until the
desired amount of Dosing Capsules is
lled and insert them into the Maga-
zine. The Magazine can hold up to 8
Dosing Capsules.

2928
11. ACCESSORIES
Attaching the Magazine Cap
After lling the Dosing Capsules, at-
tach the Magazine Cap and close it by
turning it clockwise.
Filling the Dosing Capsules with
aromatic Oils
The Dosing Capsules with inserted
Drip Pad, which are available as acces-
sories, can be lled with aromatic oils
and store them in the Magazine.
Dosing Capsule with removed cap and
inserted Drip Pad
Please make sure to not over-
ll the Drip Pad. It can contain
up to 5 drops.
Attach the cap onto the Dosing Cap-
sule. Repeat the lling process until the
desired amount of Dosing Capsules is
lled and insert them into the Maga-
zine. The Magazine can hold up to 8
Dosing Capsules.
Attaching the Magazine Cap
After lling the Dosing Capsules, at-
tach the Magazine Cap and close it by
turning it clockwise.
Inserting the Dosing Capsules
Turn the Cooling Unit with a 90° rota-
tion counterclockwise in order to re-
move it from the MIGHTY Vaporizer.
Removal of Cooling Unit (with Mouthpiece)
11. ACCESSORIES
The inserted Dosing Capsule
Insert the Dosing Capsule with the cap
facing upwards into the Filling Cham-
ber of the MIGHTY Vaporizer.
Then re-mount the Cooling Unit by ro-
tating it clockwise through 90°.
The Filling Chamber of the MIGHTY
can be lled directly as well (without a
Dosing Capsule), see Chapter 8. “Fill-
ing the Filling Chamber”, page 19.
As soon as the lower Filling Chamber
Screen is clogged or shows deposits,
a cleaning of the Filling Chamber is
needed. For that, please rstly remove
the lower Screen as described in Chap-
ter 10.3. “Removal of the lower Filling
Chamber Screen”, page 26 and
clean the Filling Chamber with a cotton
stick that has been soaked in alcohol.
Please make sure that no alcohol
drops into the inner of the device. Af-
ter cleaning, a new screen is to be in-
serted.

3130
11. ACCESSORIES
11.2. Disposable Lip Piece for Hy-
gienic Use
The Lip Piece, which is available as an
accessory, will be delivered brand new
and in a low-germ, but not fully-sterile
state.
The Lip Piece is equipped with
a check valve. This check
valve reduces the danger of a
potential contamination inside the
Cooling Unit by preventing breathing
into the Cooling Unit.
Cooling Unit with Mouthpiece and Lip Piece
The Lip Piece is put on the folded out
Mouthpiece, slid until stop and is then
ready for operation.
The Cooling Unit with Mouthpiece and
the Lip Piece may be used by only one
person.
A Lip Piece may be used for max. 4
hours after initial operation if it is un-
damaged and clean. Afterwards, it
must be disposed of in the household
waste and a new Lip Piece must be
used due to hygienic reasons.
Every further use beyond this or the
use of damaged and/or contaminated
products respectively is the user’s re-
sponsibility.
We assume no liability if this recom-
mendation is ignored.
Please note that damaged or
brittle Lip Pieces are not to be
used.
Power Adapter:
Power consumption: 36 W
Supply voltage: 100-240 V / 50-60 Hz
Output voltage: 12 V DC
MIGHTY Vaporizer:
Supply voltage: 12 V DC
The voltage details are located on the respective type labels of the MIGHTY
Vaporizer and power adapter.
Power required by MIGHTY Vaporizer: 36 W
Operating temperature: 5°C - 40°C / 41°F - 104°F
Vaporization Temperature:
adjustable between approx. 40°C - 210°C / 104°F - 410°F
Size: 14 x 8 x 3 cm (5.5 x 3.2 x 1.2 inch)
Weight: approx. 235 g (0.5 lb)
Please unplug the power adapter from the mains socket to completely disconnect
from the mains power supply.
Subject to technical changes.
Patents and designs:
www.storz-bickel.com/patents
Manufacturer:
Storz & Bickel GmbH & Co. KG
In Grubenäcker 5-9
78532 Tuttlingen, Germany
12. TECHNICAL SPECIFICATIONS

3332
The devices comply with the following EC Directives:
DIN EN 60 335
DIN EN 60 950
Electromagnetic Compatibility 2004/108/EG
13. DECLARATION OF CONFORMITY 14. WARRANTY, LIABILITY
14.1. Warranty
Storz & Bickel GmbH & Co. KG and
Storz & Bickel America Inc., as sellers,
hereby guarantee the customer, that
the product will be free from defects
in accordance with the specications
of German law, and pursuant to our
General Terms and Conditions (GTC),
upon which the purchasing agreement
are based. Of course, Storz & Bickel
will only be subject to a warranty ob-
ligation if the customer has purchased
the products directly from us. If prod-
ucts are purchased from third parties,
warranty claims may only be asserted
against these third parties, and Storz &
Bickel cannot provide any information
on the content of such claims.
In clarication, we would like to note
once again, that the warranty extends
only to correcting such initial defects
that exist despite proper handling of
the product in consideration of this
Instructions for Use and further infor-
mation provided to users. Normal wear
or tear to the products – and especially
to the batteries - is not considered a
defect under warranty law. If the cus-
tomer has commissioned third parties
with completing maintenance or repair
of the product, or if the customer uses
external products, Storz & Bickel’s
warranty obligations will only exist if
the customer can prove that the defect
was not caused by use of the external
service or external product.
Storz & Bickel will decide at its own
discretion whether to correct a defect
covered by warranty law through re-
pair or by delivering a new product to
the customer.
Any warranty claims must be directed
to Storz & Bickel GmbH, In Grubenäck-
er 5-9, 78532 Tuttlingen. American
and Canadian customers should di-
rect warranty claims to Storz & Bickel
America Inc., 1078 60th Street, Suite
A, Oakland, CA 94608. Please send the
complete defective item to us, not dis-
assembled, with invoice. Please use
external packaging that would prevent
any damage during transportation.
In order to avoid misunderstandings,
we would like to note that all informa-
tion on our products provided in this
Instructions for Use or elsewhere
does not represent any guarantee of
features or durability, unless we have
expressly referred to a guarantee for
such features or durability.
14.2. Liability
Storz & Bickel shall be liable for any
damages caused to the customer by
our products in accordance with Ger-
man law and pursuant to our GTC. Un-
der said provisions, we are only liable for
damages caused by intentional action
or gross negligence, unless such dam-
ages involve death, personal injury, or
injury to health, or if the injury is related

34
14. WARRANTY, LIABILITY
to a cardinal contractual obligation. In
such cases, we will also be liable to the
customer for simple negligence.
14.3. Copyright
This document is copyright protected,
and may not be used either in whole or
in part pursuant to Sections 15 et seqq.
UrhG (German Copyright Act) without
prior written approval of Storz & Bickel.

STORZ & BICKEL GMBH & CO. KG
In Grubenäcker 5-9 · 78532 Tuttlingen/Germany
©by STORZ & BICKEL GmbH & Co. KG · MAL-30-204 09-2018-sec_EN · Subject to alterations · All rights reserved