Strata Furniture Addison User manual

Addison Instructions
Page 1 of 8
Parts in the Arm Box:
Parts in the Body Box:
Strata
Strata
urniture
1A
1B
Watch our assembly videos at www.stratafurniture.com/videos.html
Arm - Outside View Arm - Inside View
Stretcher x 1 Foot Connector Bar x 1 Advance Arms x 2Back Panel Corbel x 1
Corbels x 4
Seat Deck x 1
with the Feet attached
Back Deck x 1 Back Panel x 1

Hardware in the Body Box:
Addison Instructions
Page 2 of 8
Strata
Strata
urniture
2A
Bolts (60mm) x 6
For the Advance Arms
and the Foot Connector Bar
Long Bolts (80mm) x 10
For the Stretcher and Back Panel
Short Bolts (30mm) x 2
For the Back Panel Corbels
Bolts (50mm) x 4
For the Arm Corbels
Washers x 8 Locking Pins x 4Long Clevis Pins x 2
Short Clevis Pins x 2
Barrel Nuts x 10
Long Allen Key x 1 Plastic Runner x 2 Bungees x 2 Strap x 1
Fit the Wooden Dowels into the Stretchers
2B
End of Stretcher
Wooden Dowels
Wooden Dowels x 12
Long Sleeve
x 2
Short Sleeve
x 4
Screw x 4

Assemble the Back Panel between the Arms
Addison Instructions
Page 3 of 8
Strata
Strata
urniture
3A
Wooden Dowels
Wooden Dowels
Barrel Nut
Barrel Nuts
Barrel Nuts
Back Panel Corbel Long Bolts (80 mm)
Short Bolts (30 mm)
Long Bolts (80 mm)
Fit Wooden Dowels into back panel.
Bolt the parts together using the Long Bolts (80mm) and Barrel
Nuts as shown. It is helpful to keep the frame squared.
Be patient, it can be tricky to start the bolts in the nuts - A
screw driver will help you line up the Barrel Nut with the Bolt.
Drive the Bolts in until they just catch the Nuts.
Attach the Back Panel Corbel to the Back Panel using the Short
Bolts (30 mm).

Assemble the Stretcher between the Arms
Addison Instructions
Page 4 of 8
Strata
Strata
urniture
4A
Wooden Dowels
Wooden Dowels
Stretcher
Barrel Nuts
Back Panel
Long Bolts (80 mm)
Long Bolts (80 mm) Fit the Stretcher, with the Barrel Nut holes on the inside, to the
inside edge of the Arms.
Bolt the parts together with four Long Bolts (80mm) and Barrel
Nuts.
Drive the Bolts in until they just catch the Nuts.

Addison Instructions
Page 5 of 8
Strata
Strata
urniture
5A
Back Deck
Back Deck
Seat Deck
Seat Deck
Plastic Runner
Plastic Runner
Long Clevis Pin
Short Clevis Pin
Short Clevis Pin
Washer
Washer
Advance Arm - Slot end outwards!
Advance Arm - Slot end outwards!
Rotate the Back Deck upright.
Slide the short clevis pin through
the back deck, then through a washer
and then through the hole in the Advance
Arm. Secure with a Locking Pin.
Long Clevis Pin
Short Sleeves
Short Sleeves
Stickers
Fit the Advance Arms to the Back Deck.
5B
Lock the clevis pin with a washer
and locking pin.
The Long Clevis
pin goes through
the plastic runner
first,then the
two sleeves
Join the Seat and Back Deck together.
Lay both Decks out flat on the floor with the stickers facing upwards.
The Seat Deck fits inside the Back Deck as shown. Slip the Long
Clevis Pin through the small end of the Plastic Runner,
then two small sleeves, then through the hole in
the Back and Seat Deck. Secure with a
Washer and Locking Pin.

Addison Instructions
Page 6 of 8
Strata
Strata
urniture
6A
Seat Deck
Foot Connector Bar
Back Deck
Foot
Foot
Foot Foot
Bolts (60mm)
Assemble the Bungees under the Seat Deck.
6B
Attach the Connector Bar to the Legs.
Lift the Seat Deck so it is
resting on the Back Deck, the
feet should be pointing
DOWNWARDS.
Line up the holes between the
Connector Bar and the Feet.
Make sure the recess for the
bolt is facing outwards.
CAUTION: The metal insert
in the foot MUST be facing
the Back Deck.
Use four Bolts (60 mm) and
bolt it in place.
Bolts (60mm)
Screw the Bungees to the side of the two inner
rails. Screw the lower end of the Bungee chord
first, then stretch the Bungee over the
Connector Bar. Screw in the top end.
Seat Deck
Screw
Screw
Screw
Bungee
Bungee
Inner Rail

Addison Instructions
Page 7 of 8
Strata
Strata
urniture
All joints must
be left loose.
Arm
Back Panel
Washer
Long Sleeve
Washer
Advance Arm
60mm Bolt
Please Note:
Use 2 people!
All joints must
be left loose.
Fit the Strap to the Back Deck
Connect the Advance Arms to the Arms.Fit the Seat Back Decks to the Frame.
7A 7B
7C
Insert the decks into the partially completed
frame. This is where a helper may be useful.
When the Plastic Runners are in the grooves in
the Arms, slide the assembly towards the back
of the frame.
Tighten all Stretcher and Back Panel Bolts.

Addison Instructions
Page 8 of 8
Strata
Strata
urniture
8A
To convert into a couch position
Watch our videos at www.stratafurniture.com/videos.html
Attach the Corbels to the Arms.
Operating Instructions
Fit the dowel at the top of the Corbel into the
hole on the underside of the Arm, and then fit
the other dowel into the side of the Arm.
•Remove any pillows and other obstructions
•Push up the mattress into an inverted couch position
and then lift up the seat deck into a vertical position.
•Resting seat deck on your hip, push the foot
connector down all the way so that the foot
connector rests on the side rail.
•With one hand lightly push the seat deck
down. Then, at the same time, pull on the
top of the mattress with one hand (or the
strap if using a strap) and push in the seat
deck with your other hand or leg until it
locks in.
*DO NOT FORCE! - Frame should operate
easily.
To convert into a bed position
•Lift seat deck up just so it clears the front stretcher. PULL
HORIZONTALLY until the rollers hit the top of the front of the
groove. Then lift into vertical position. At this point, it will look like the
picture above. If you lift vertically too quickly, the frame will slam down.
•Resting the seat deck on your hip, push the seat deck and mattress forward
(towards the back deck) until you can pull the foot
connector bar out towards you until feet are fully
extended.
•Sit the frame down gently. Note: Never lift the frame
by the arm caps - Always lift
from the bottom of the arms.
Arm
Corbel
Bolt (50mm)