Strata Furniture Galena Arms User manual

Galena Arms
Page 1 of 1
Arm - Outside View Arm - Inside View
Parts in the Arm Box:
Hardware in this Box:
1A
1B
Bolts (60mm) x 8 Barrel Nuts x 8 Wooden Dowels x 8 Wood Buttons x 8
Watch our assembly videos at www.stratafurniture.com/videos

(Longer than Seat Deck Rails)
Hardware in Body Box Hardware in Arm Box
-not shown above-
Parts in two body boxes, arms not shown
12
48
Queen size frames have 26
identical size slats, 13 for
each deck
* 52 for queen size
Thank you for purchasing one of our products! We hope the instructions below make the process go
smoothly. We strive to have high quality products and perform numerous quality control steps to ensure all
the hardware is provided and no issues occur during assembly. In the rare case something is missing,
please contact us directly during business hours at [phone] or after hours at [phone]. You can
also reach us at [email protected]. Also, if one of the steps below do not make sense and you need
help figuring it out, we are more than glad to walk you through the assembly. We hope you enjoy your futon!

2A


Coach Frame Assembly Instructions
2 B  


  




 

 
  

 

Attach the Arms* to the Stretchers using separate hardware received
in arm box.


 

 
 

 
 
2A 2B 2B

For full size frames, use the shorter slats for the back deck. Queen size frames use the same size slats on both decks.
Use the longer rails for the back deck
Full size Slats shown.
Queen size uses 13
of the same size slats
for each deck
3A
3B
3A
3A
Completed left side of back deck
Put a 30mm bolt through the counter-sunk holes at the
end of each slat and then into the pre-drilled holes on
the back deck support boards. Repeat this for all of the
slats and tighten all bolts securely.
You can use a power driver with the clutch set on low
to snug up the bolts after you hand start them. Finish
tightening them by hand only.

For full size frames use the longer slats on the seat deck. Queen size frames use the same size slats
for both decks.
Please use shorter rails for the seat deck
Full size slats are
shown here. Queen
size uses 13 of the
same size slats for
each deck
Completed seat deck
Put a 30mm bolt through the counter-sunk holes at the
end of each slat and then into the pre-drilled holes on the
seat deck support boards. Repeat this for all of the slats
and tighten all bolts securely.
You can use a power driver with the clutch set on low to
snug up the bolts after you hand start them. Finish
tightening them by hand only.

When connecting the decks, either
rotate the foot on each side of seat
deck 180 degrees or rotate the foot
perpendicular to the seat deck.

Please notice correct side of foot to attach foot connector board to foot.
Correct
Incorrect
Critical that the bolt is
inserted on correct side of foot



Coach Frame Assembly Instructions
7A
Tighten all eight Bolts.
7B
Connect the Advance Arms to the Arms.
7C   
7D
Fit the Wood Buttons to the Arms and
Back Deck
  

 
 
  
Page 7 of 8



Fit the Strap to the Back Deck.
 


7A
7B
7B
7D

Please see
operating videos at
www.stratafurniture.com
Keep the feet snugly
attached to the seat
deck!
Frame in bed
position After pushing up the
mattress, lift the seat
deck into a vertical
position.
Push the foot connector all the way in so that
the foot connector rests on the side end caps
and locks the feet in place.
With one hand lightly push the
seat deck down while pulling
on the top of the mattress with
the other hand or the strap and
push the seat deck back and
down until it locks in place.
PLEASE NOTE:
Temperature and humidity can affect the tightness of
you frame. It is important to periodically check all
connections for tightness. We have included a 13mm
open-end wrench and a 5mm Allen-head key to use
to keep the feet snugly attached to the Seat Deck End
Caps for proper operation.