Strata Furniture Fremont User manual

Fremont Arms
Page 1 of 1
Parts in the Arm Box:
Hardware in this Box:
Strata
Strata
urniture
1A
1B
Wood Buttons x 8
Bolts (80mm) x 8 Barrel Nuts x 8 Wooden Dowels x 8
Arm - Outside View Arm - Inside View
Watch our assembly videos at www.stratafurniture.com/videos.html

Assembly Instructions for Carriage Body, all sizes
Page 1 of 6
Parts in the Body Box:
Back Deck x 1
Stretcher x 2
Seat Deck x 1
with the Feet attached
Foot Connector Bar x 1
Advance Arms x 2
Hardware in the Box:
Bolts (60mm) x 6
For the Advance Arms
and the Foot Connector Bar
Long Clevis Pins
x 2 Short Clevis Pins
x 2
Washers
x 8
Long Sleeve
x 2
Short Sleeve
x 4
Plastic Runner
x 2
Bungees
x 2
(x4 for Queen Size)
Screw
x 4
(x8 for Queen Size)
Strap
x 1
Long Allen Key
x 1
Locking Pins
x 4
Strata
Strata
urniture
1A
1B
Watch our assembly videos at www.stratafurniture.com/videos.html

Page 2 of 6
Assembly Instructions for Carriage Body, all sizes
Fit the Wooden Dowels into the Stretchers Attach the Arms* to the Stretchers using hardware in arm box.
Be patient, it can be tricky to start the bolts in the nuts -
a screwdiver will help you line up the Barrel Nut with the Bolt.
Drive the Bolts in until they just catch the Nuts.
It is important that these bolts are left loose!
*Your arm style may vary.
Strata
Strata
urniture
2A 2B
End of Stretcher
Wooden Dowels
Wooden Dowels
Bolts
Bolts
Allen Key
Leave Bolts LOOSE!
Stretcher
Barrel Nuts
FRONT SIDE
Arm*
Arm*
Bolts
Bolts
Wooden Dowels
Wooden Dowels
Barrel Nuts
Leave Bolts LOOSE
at this stage!

Assembly Instructions for Carriage Body, all sizes
Page 3 of 6
Back Deck
Back Deck
Seat Deck
Seat Deck
Plastic Runner
Plastic Runner
Long Clevis Pin
Short Clevis Pin
Short Clevis Pin
Washer
Washer
Advance Arm - Slot end outwards!
Advance Arm - Slot end outwards!
Rotate the Back Deck upright.
Slide the short clevis pin through
the back deck, then through a washer
and then through the hole in the Advance
Arm. Secure with a Locking Pin.
Long Clevis Pin
Short Sleeves
Short Sleeves
Stickers
Fit the Advance Arms to the Back Deck.
Strata
Strata
urniture
3A
3B
Lock the clevis pin with a washer
and locking pin.
The Long Clevis
pin goes through
the plastic runner
first,then the
two sleeves
Join the Seat and Back Deck together.
Lay both Decks out flat on the floor with the stickers facing upwards.
The Seat Deck fits inside the Back Deck as shown. Slip the Long
Clevis Pin through the small end of the Plastic Runner,
then two small sleeves, then through the hole in
the Back and Seat Deck. Secure with a
Washer and Locking Pin.

Assembly Instructions for Carriage Body, all sizes
Page 4 of 6
Seat Deck
Foot Connector Bar
Back Deck
Foot
Foot
Foot Foot
60mm Bolts
Assemble the Bungees under the Seat Deck.
Strata
Strata
urniture
4A
4B
Attach the Connector Bar to the Legs.
Lift the Seat Deck so it is
resting on the Back Deck, the
feet should be pointing
DOWNWARDS.
Line up the holes between the
Connector Bar and the Feet.
Make sure the recess for the
bolt is facing outwards.
CAUTION: The metal insert
in the foot MUST be facing
the Back Deck.
Use four Bolts (60 mm) and
bolt it in place.
60mm Bolts
Screw the Bungees to the side of the two inner
rails. Screw the lower end of the Bungee chord
first, then stretch the Bungee over the
Connector Bar. Screw in the top end.
FOR QUEEN SIZES: Screw the additional,
smaller bungees to the middle, inner rails.
(Not shown)
Seat Deck
Screw
Screw
Screw
Bungee
Bungee
Inner Rail

Page 5 of 6
All joints must
be left loose.
Back Deck
Washer
Long Sleeve
Washer
Advance Arm
60mm Bolt
Please Note:
Use 2 people!
All joints must
be left loose.
Assembly Instructions for Carriage Body, all sizes
Tighten all eight Bolts.
Connect the Advance Arms to the Arms.
Fit the Seat Back Decks to the Frame.
Strata
Strata
urniture
5A 5B
5C
Insert the decks into the partially completed
frame. This is where a helper may be useful.
When the Plastic Runners are in the grooves in
the Arms, slide the assembly towards the back
of the frame.

Wood
Buttons
Page 6 of 6
Assembly Instructions for Carriage Body, all sizes
To convert into a couch position
Watch our videos at www.stratafurniture.com/videos.html
Fit the Wood Buttons to the Arms.
Fit the Strap to the Back Deck.
Strata
Strata
urniture
6A Operating Instructions
6C
Finally, when the frame is fully assembled,
make sure all the bolts are secure.
Push fit or lightly tap the Wood
Buttons into the bolt holes on
the Arms.
•Remove any pillows and other obstructions
•Push up the mattress into an inverted couch position
and then lift up the seat deck into a vertical position.
•Resting seat deck on your hip, push the foot
connector down all the way so that the foot
connector rests on the side rail.
•With one hand lightly push the seat deck
down. Then, at the same time, pull on the
top of the mattress with one hand (or the
strap if using a strap) and push in the seat
deck with your other hand or leg until it
locks in.
*DO NOT FORCE! - Frame should operate
easily.
To convert into a bed position
•Lift seat deck up just so it clears the front stretcher. PULL
HORIZONTALLY until the rollers hit the top of the front of the
groove. Then lift into vertical position. At this point, it will look like the
picture above. If you lift vertically too quickly, the frame will slam down.
•Resting the seat deck on your hip, push the seat deck and mattress forward
(towards the back deck) until you can pull the foot
connector bar out towards you until feet are fully
extended.
•Sit the frame down gently. Note: Never lift the frame
by the arm caps - Always lift
from the bottom of the arms.