Strata Furniture Adriana User manual

A d r i a n a
Parts in Box 1
1A
Parts in Box 2
1B
S t r a t a F u r n i t u r e
Page 1 of 8
Assembly Instructions for all sizes.
**AD 0306**
Parts in Box 3
1C
Arm- inside viewArm- outside view Advance Arms x 2
Back Deck x 1
Seat Deck x 1
with the Feet attached
Back Panel x 1
Foot Connector
Bar x 1
Stretcher x 1

Hardware in this Box:
2A A d r i a n a
S t r a t a F u r n i t u r e
Page 2 of 8
Assembly Instructions for all sizes.
**AD 0306**
Long Allen Key
x 1
Locking Pins
x 4
Short Clevis Pins
x 2
Bungies
x 2
Screw
x 4
Sleeve
x 2
Bolts (100mm) x 8
for the Stretcher
and Back Panel
Bolts (60mm) x 6
For the Advance Arms
and the Foot Connector Bar
Thumb Nuts
x 2
Washers
x 10
Long Clevis Pins
x 2 Plastic Runner
x 2
Wood Button
x 8
Barrel Nuts
x 6
Strap x 1

Assemble the Back Panel between the Arms.
3A A d r i a n a
S t r a t a F u r n i t u r e
Page 3 of 8
Assembly Instructions for all sizes.
Use 2 People!
Please Note:
Bolt the parts together with using the Bolts and Nuts as
shown in the drawing. It is helpful to keep the frame squared.
Be patient, it can be tricky to start the bolts in the nuts - a
screwdriver will help you line up the Barrel Nut with the Bolt.
Drive the Bolts in until they just catch the Nuts.
It is important that these bolts are left loose !
**AD 0306**
Thumb
Nut
Wooden
Dowel
Thumb
Nut
Back Panel
100mm JCB
Barrel
Nut
100mm JCB
Wooden
Dowel Barrel Nut
100mm JCB

100mm
Bolts
Barrel
Nuts
Back Panel
Stretcher
100mm
Bolts
Barrel
Nuts
Wooden
Dowels
60mm Bolt
Sleeve
Washer
Washer
Advance Arm
Wood Block
Note! Recess for Clevis Pin
The slotted end of the Advance Arm attaches to the
little wood block at the back of the Arm. Slip a
washer and Sleeve over the Bolt, and pass it
through the slot. Add another washer and fix it to
the Arm. Tighten the Bolt. Be sure that the Advance
Arm moves freely. Rotate so that it is pointing up.
Fit the Stretcher between the Arms. Bolt the parts together
with four long Bolts (100mm) and Barrel Nuts.
Drive the Bolts in until they just catch the Nuts.
It is important that these bolts are left loose !
Assemble the Stretcher between the Arms.
4A A d r i a n a
S t r a t a F u r n i t u r e
Page 4 of 8
Assembly Instructions for all sizes.
Attach the Advance Arms to the Arms
4B
Leave the
Advance Arm
pointing up.
**AD 0306**

Join the Seat and Back Deck together.
5A
Lay both Decks out flat on the floor with the stickers facing upwards.
The Seat Deck fits inside the Back Deck as shown. Slip the Long
Clevis Pin through the small end of the Plastic Runner, through the
hole in the Back Deck and the corresponding hole in the Seat Deck.
Secure with a Washer and Locking Pin.
A d r i a n a
S t r a t a F u r n i t u r e
Page 5 of 8
Assembly Instructions for all sizes.
**AD 0306**
Long Clevis Pin
Sticker
- facing upwards
Plastic
Runner
Long
Clevis Pin
Plastic Runner
Back Deck
Seat Deck
Sticker
- facing upwards
Sticker
Sticker
Washer
Washer
Lock the Clevis
Pin with a washer
and Locking Pin
Washers

Attach the Connector Bar to the Legs.
6A
Assembly Instructions for all sizes.
Lift the Seat Deck so it resting on the Back Deck.
The feet should be pointing downwards.
Line up the holes between the Connector Bar and the
Legs. Make sure the recess for the head of the Bolt is
facing outwards.
Use four short Bolts (60mm) and bolt it in place.
Screw the Bungies to the side of the two inner
rails. Fix the lower end of the Bungie chord first,
then stretch the Bungie over the Connector Bar.
Fix the top end.
Assemble the Bungies under the Seat Deck.
6B
A d r i a n a
S t r a t a F u r n i t u r e
Page 6 of 8
**AD 0306**
60mm
Bolts
Foot Connector Bar
Foot
60mm Bolts
Foot
Back Deck
Seat Deck
Screw
Bungie
Inner Rail
Screw
Screw
Screw
Inner Rail
Back Deck
Seat Deck

Fit the Seat and Back Decks to the Frame.
7A
Insert the decks into the partially completed
frame. This is where a helper may be useful.
When the guides are in the grooves in the
Arms, slide the assembly to the back of the
frame.
Tighten all Stretcher and Back Panel Bolts.
Use 2 People!
Please Note:
All joints must
be left loose.
A d r i a n a
S t r a t a F u r n i t u r e
Page 7 of 8
Assembly Instructions for all sizes.
All joints must
be left loose.
Connect the Advance Arms
to the Arms.
7B
7C Fit the Strap to the
Back Deck.
**AD 0306**
Advance Arm
Clevis Pin
Secure with a Washer
and Locking Pin.

Wood
Buttons
Wood
Button
Wood
Button
Fit the Wood Buttons to the Arms.
8A
Page 8 of 8
Assembly Instructions for all sizes.
Finally, when the frame is fully assembled,
make sure all the bolts are secure.
Note: Never lift the frame by the
arm caps - Always lift from
the bottom of the arms.
Push fit or lighly tap the Wood Buttons into
the bolt holes on the Arms
A d r i a n a
S t r a t a F u r n i t u r e
To convert into couch position:
Lift up the seat deck into a vertical position.
Resting seat deck on your hip, rotate the foot connector
towards you until the feet are fully extended.
Set the frame down gently.
Operating Instructions:
To convert into bed position:Operating Instructions:
•
•
•
Correct Foot position
Remove any pillows and other obstructions. Reach to
the back and lay the strap on top of the mattress.
Lift up the seat deck into a vertical position.
Resting seat deck on your hip,
push the foot connector down all
the way so that the foot connector
touches the side rail -
It is Very Important that the feet are
in proper position - see diagram.
With one hand lightly push the seat
deck down and with other hand
pull the back using the Strap, making
sure that the matress clears back rail.
Push the seat deck in all the way.
•
•
•
•
•
DO NOT FORCE - the frame should operate easily.
**AD 0306**