Techni Mobili RTA-988D User manual

Thank you for purchasing our product.
MODEL RTA-988D
ASSEMBLY INSTRUCTIONS
REV.CAR-6643-0622

P. 1 RTA-988D P. 1
•Please read carefully the assembly instructions
before the installation.
•Do not discard this manual or any of the packaging
material until the unit has been completely
assembled.
•Might require of two people for the assembly.

P. 2 RTA-988D P. 2
1
x1 2
x1
Tabletop Left side panel
MAIN PARTS LIST
3
x1 4
x1
Top front panel Left front panel
5
x1 6
x1
Right-top side panel Top back panel
7
x1 8
x1
Right side panel Middle side panel

P. 3 RTA-988D P. 3
9
x1 10
x1
Cabinet top panel Cabinet bottom panel
MAIN PARTS LIST
11
x2 Cabinet skirt panel 12
x2 Drawer front panel
13
x1 Cabinet back panel 14
x2 Drawer back panel
15
x2 Drawer bottom 16
x4 Drawer side panel

MAIN PARTS LAYOUT (FOR REFERENCE):
P. 4 RTA-988D P. 4
9
10
12
13
15
8
(2x)
1
2
7
6
11
11
16
16
4
14
3
5

P. 5 RTA-988D P. 5
LIST OF INCLUDED HARDWARE
PART
QTY ITEM
A76 M3.5x14
B4M3.5x25
C8Plastic
dowel
D4Large metal
bracket
E2Small metal
bracket
F1Flat metal
bracket
G24 M6x30
Wooden dowels
H4M3.5x40
I7Plastic
bracket
J6Plastic glide
PART QTY ITEM
K16 M5x30 Bolt
L16 15x11
Cam lock
M18 10x10
Nail
N6Hole cover
O2Plastic
handle
P2
Sets
Metal
sliders, set
of 4 pcs
TOOLS THAT ARE REQUIRED (But not included)
Phillips Screwdriver Hammer
“Flat”: 2 pcs, go inside
the cabinet
“L shaped”: 2 pcs, go
on the drawers

P. 6 RTA-988D P. 6
☛This unit uses cam bolts and locks. The following explains how to use them.
This is not an assembly step; it is a guide for when you are actually doing the
assembly using this kind of hardware.
Cam Bolt
Cam Lock
1. Screw the bolt into the corresponding hole
on panel “A”.
3. Insert the cam lock on panel “B” making
sure it goes aligned to receive the bolt’s head.
4. Turn the cam lock clockwise. This will lock the
parts together and will close any gaps.
Alignment: The cross points
towards the panel “A” with the bolt.
2. Join panel “B” to panel “A”. If panel “B” comes
with the cam lock pre-installed, make sure it is
aligned to receive the bolt’s head (refer to point
3). There might be a very small gap between the
panels which is normal.
Panel “B”
Panel “B”
Panel “B”
Panel “B”

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
❶Do aquick inventory
to make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged
and defective parts can
be replaced at no cost
to you. Please refer to
the last pages on this
manual.
❹If during assembly
you find an issue or
need clarification, please
contact our Customer
Service for assistance.
Please refer to the last
pages on this manual.
❺On each step read the
instructions and analyze
the illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you
understand which
hardware will be used on
each step.Using the
wrong size of screw, bolt
or pin might strip the
threads or cause damage
to the part in which it is
being used.
❼To avoid
misalignments, always
leave the screws loose
and tighten them until
all pieces are
positioned correctly.
❾Sometimes the laminate might cover
partially or entirely the hole on apanel.If there
is no visible hole for the screw, pass and press
the tip of your finger over the area where the
hole should be located to feel the indentation,
and once found, carefully pierce the laminate to
reveal the hole underneath.
❿If the hole seems too small for the screw,
first make sure you are using the correct size of
screw and that it’s been installed in the correct
hole.If the hole still appears to be too small,
carefully pierce the laminate to reveal the
hole’s actual size.
P. 7 RTA-988D P. 7
❸The replacement parts
service is limited to the
48 contiguous United States.
If you reside in Alaska,
Hawaii, Puerto Rico,
U.S. territories or other
countries, please contact the
supplier from where the unit
was purchased.

ASSEMBLY STEPS
Install the wooden dowels Ginto the indicated holes on panels 2, 6, 7, 8,
10, 11 and 13.
P. 8 RTA-988D P. 8
6
2
STEP 1
Hardware:
GM6x30
Wooden
dowels
24
Pcs
Tools required
(But not included)
IT IS RECOMMENDED TO PLACE THE PIECES OVER BLANKETS TO PROTECT THEIR
FINISH DURING ASSEMBLY.
(Top)
(Top)
(Back)
(Bottom)
(Front)
(Front)
(Bottom)
8
7
10
13
x2
11
(Back)
G

P. 9 RTA-988D P. 9
Install the bolts Kinto the indicated holes on panels 1, 2, 7, 8and 9.
2
1
STEP 2
Hardware:
KM5x30
Bolt
16
Pcs
Tools required
(But not included) (Top)
(Back)
(Top)
(Bottom)
(Back)
(Front)
(Front)
(Top)
(Bottom)
(Back)
(Front)
8
7
9
K
K
K
O
P

P. 1 0 RTA-988D P. 1 0
Assemble the “Flat” sliders P to the set of holes on the top and middle of
the side panels 7 and 8 with screws A. Please note:
•The wheel is at the front, and faces down with 2 holes above it.
•The sliders attach at the front on the 2nd and 3rd holes.
•The sliders will be receded from the front edge of the panels.
7
Grab the two sets of sliders P (total 8pcs) and separate them into 2
groups according to their shape:
-The “Flat” ones will be used on the next step.
-The “L Shaped” will be used until step 12, set them aside.
STEP 3
(“Flat” Right, x2)
(Front)
The “Flat” ones will be used on step 4.
The “L-Shaped” will be used on step 12, set them aside.
PP
PP
(“Flat” Left, x2)
(“L” Right, x2) (“L” Left, x2)
(Front)
(Front)
(Back)
(Front)
(Back)
(Top)
(Top)
(Bottom)
(Bottom)
(Front)
P
STEP 4
Hardware:
AM3.5x14
12
Pcs
P“Flat”
4
Pcs
Tools required
(But not included)
8
Flat-Left
(Front)
Flat-Right
P
P
P
A

P. 11 RTA-988D P. 11
•Join the cabinet’s bottom panel 10 and back panel 13 to the right side
panel 7,making sure the big holes for the cam locks go facing
towards the inside and the bottom respectively.
•Insert the cam locks Linto 10 and 13, and turn them to lock the
pieces together as shown and as explained in page 6.
•Join the cabinet’s skirt panels 11 to the right side panel 7.
•Join the middle side panel 8to panels 10, 11 and 13.
•Insert the cam locks Linto 10 and 13, and turn them to lock the
pieces together as shown and as explained in page 6.
Cam locks
alignment on 10
and 13
(Top)
(Bottom)
(Front)
10
7
STEP 5
Hardware:
L
Cam lock
4
Pcs
Tools required
(But not included)
STEP 6
Hardware:
L
Cam lock
4
Pcs
Tools required
(But not included)
8
13
10
Cam locks
alignment on 10
and 13
(The sliders on 8
are located on the
inside at the top)
(Front)
(Back)
13
L
7
11
11
L

P. 1 2 RTA-988D P. 1 2
Attach the bottom plastic glides Jto the bottom of panels 7and 8with
screws Aas shown.
8
8
7
STEP 8
Hardware:
AM3.5x14
8
Pcs
J4
Pcs
Tools required
(But not included)
•Join the cabinet’s top panel 9 to the side panels 7 and 8.
•Insert the cam locks Linto 7 and 8, and turn them to lock the pieces
together as shown and as explained in page 6.
STEP 7
Hardware:
L
Cam lock
4
Pcs
Tools required
(But not included) Cam locks
alignment on 7
and 8 97
L
A
J

P. 1 3 RTA-988D P. 1 3
•For each of the two drawers, install the plastic dowels Cto the side
panels 16.
•For each of the two drawers, join the side panels 16 to the front panel
12 as shown.
For each of the two drawers, assemble the back panel 14 to the side
panels 16 with screws H.
16
12
16
14
STEP 9
Hardware:
CPlastic
dowel
8
Pcs
Tools required
(But not included)
STEP 10
Hardware:
HM3.5x40
4
Pcs
Tools required
(But not included)
(Top)
(Bottom)
(Front)
(Back)
(Front)
(Back)
16
16
16
x2
C
x2
H

P. 1 4 RTA-988D P. 1 4
•For each of the two drawers, place the bottom panel 15 over the
bottom of the drawer frame and slide it into the groove of the front
panel 12.
•Secure the bottom panel 15 with nails Mat the indicated positions.
For each of the two drawers, attach the “L” shaped sliders Pto the
bottom of the drawers on their respective sides with screws Aas shown.
Make sure that the wheel go towards the back, and that they don’t
protrude, otherwise, the drawer raises 1” and won’t fit in the cabinet.
15
15
STEP 11
Hardware:
MNail
18
Pcs
Tools required
(But not included)
STEP 12
Hardware:
AM3.5x14
8
Pcs
P“L shape”
4
Pcs
Tools required
(But not included)
(Top)
(Bottom)
(Front)
When finished, the sliders
should look like this from the
back of the drawer:
The assembly shown below
is incorrect, it raises 1” and
the drawer won’t fit:
(Front)
FRONT: BACK:
“L”-Right
P
12
M
x2 x2
“L”-Left
P
A
P
A
P
(Back)
x2

P. 1 5 RTA-988D P. 1 5
For each of the two drawers, attach the handle Oto the front panel 12
with screws Bas shown.
12
2
1
STEP 13
Hardware:
BM3.5x25
2
Pcs
OHandle
2
Pcs
Tools required
(But not included)
STEP 15
Hardware:
LCam lock
2
Pcs
N2
Pcs
Tools required
(But not included)
STEP 14
•Insert the drawers into the cabinet, first the bottom
one, then the top one. Insert at an angle with their
fronts facing down, making sure the wheels from
the drawer slide in the middle of the sliders inside
the cabinet.
•If the drawers don’t seem to fit, make sure the
drawers are sliding through the cabinet sliders, not
on top of them. Also review the assembly done in
steps 4 and 12 for the correct assembly of the
sliders.
Assemble the left side panel 2to the tabletop 1with cam locks Las
shown and as explained in page 6, then cover the cam locks with N.
(Left)
(Right)
(Front)
(Back)
B
O
x2
L
N

P. 1 6 RTA-988D P. 1 6
To ensure that the parts will end up aligned and as straight with each
other as possible, it is recommended to have another person holding the
pieces while doing this step.Please note that the results are not always
100%perfect.
Place the large metal brackets D well distributed along panels 1and 6,
and secure the pieces with screws Aas shown.
6
1
STEP 16
Hardware:
AM3.5x14
4
Pcs
LCam lock
2
Pcs
N2
Pcs
J2
Pcs
Tools required
(But not included)
•Assemble the top back panel 6 to the left side panel 2 with cam locks
Las shown and as explained in page 6, then cover the cam locks
with N.
•Attach the bottom plastic glides Jto the bottom of panels 2 with
screws Aas shown.
STEP 17
Requires
of 2
persons
Hardware:
AM3.5x14
12
Pcs
DLarge
bracket
3
Pcs
Tools required
(But not included) A
A
A
D
A
L
N
6
2
A
J

P. 1 7 RTA-988D P. 1 7
•Place the plastic brackets I well distributed along the grooves of
panels 3and 4 with their openings facing towards the bigger space on
the panels.
•Secure the brackets with screws A.
•Position the two front panels 3and 4at an angle as shown, and make
sure they are in good alignment.
•Secure both panels 3and 4together with the flat bracket Fand
screws Aas shown.
(Right)
STEP 18
Hardware:
AM3.5x14
7
Pcs
IPlastic
bracket
7
Pcs
Tools required
(But not included) Facing
This way
STEP 19
Hardware:
AM3.5x14
2
Pcs
FFlat
bracket
1
Pc
Tools required
(But not included)
(Top)
(Bottom)
(Left)
$
,
4
3
A
F
Align
3
4

P. 1 8 RTA-988D P. 1 8
With the help of another person, place the tabletop section over the
cabinet section, and on the back side secure panel 6 to panel 13 with
screws B from behind, then cover the screw heads with stickers N.
(Front)
(Back)
6
STEP 21
Requires
of 2
persons
Hardware:
BM3.5x25
2
Pcs
N2
Pcs
Tools required
(But not included)
•Join the front panels 3and 4with the panels 1and 2,and secure the
pieces with screws Athrough the plastic brackets Ias shown.
•Place and securethe side panel 5to panels 3and 6with the small
brackets Eand screws Aas shown.
•Secure the panel 5to panel 1withthe large bracket Dand screws A
as shown.
STEP 20
Requires
of 2
persons
Hardware:
AM3.5x14
15
Pcs
DLarge
bracket
1
Pc
ESmall
bracket
2
Pcs
Tools required
(But not included)
Efor the corners
on 3-5 & 5-6
2
1
5
6D
A
A
E
A
I
Dfor the middle
on 1-5
3
4
B
N
13

P. 1 9 RTA-988D P. 1 9
•Do not exceed the indicated weight limits.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and
water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as
underneath the tabletop.
•Do not sit on the unit or lean against it.
•Do not allow small children to play under or over the unit.
•Do not allow small children to reach inside the drawers without your supervision.
•Do not pull, push or drag the unit to move it for more than 1 feet. The unit must be lifted by
at least 2 persons when moving in the same or adjacent rooms.
•Before moving the unit, make sure to secure or remove any object that is heavy or might
fall off.
•When lifting the unit, use both hands and bend your knees, not your backs.
•When transporting the unit to places far away, it is recommended to separate the tabletop
section from the cabinet section, and protect them to avoid damage in transit.
•Shall any part of the unit become defective during the warranty period, replacement parts
might be available to you at no charge. Please refer to the last pages on this manual.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes
liability for damages or consequences due to accidents, incorrect assembly, negligence,
improper use, modifications, or not heeding the above warnings.
CARE, MAINTENANCE AND SAFETY WARNINGS:
WEIGHT LIMITS
ALL DONE!
Give yourself a nice pat on the back, you did a great job!
Enjoy your new unit.
B
C
A
A
= 13 Lbs
= 44 Lbs
= 22 Lbs
.
.
.
(6 Kg
(20 Kg
(10 Kg
)
)
)
A
C
B