Dream On Me 599 User manual

1
STYLE NO: 599
REF. PART NAME QUANTITY
Read all instructions before assembling.Save
instructions for future use.Carefully remove and lay
out all parts.Familiarize yourself with all diagrams to
facilitate the assembly of your product.Check parts
and the enclosed hardware bag with the hardware
parts list to be sure all are included and quantities
are correct.Destroy cardboard and plastic bags
immediately.
Attention:In order to properly assemble the chest,
follow the assembly instructions carefully.Failure to
assemble in the manner recommended could make
the chest hazardous.
Warning:Never use this product if there are any loose
or missing fasteners,loose joints,broken parts,or torn
mesh/fabric.check before assembly and periodically
during use.Contact Dream On Me.for replacement
parts and instructional literature if needed.
B
A
C
Left Top Panel 1
1
1
Left Front Top Rail
1
2
D
E
Back Bottom Rail
1
F
1
G
1
H
Left Side Panel
Right Side Panel
1
J
1DR1 Drawer Front Panel(Small)
2DR2 Drawer Side Panel(Small)
1DR3 Drawer Back Panel(Small)
3
DR4
3DR5
Drawer Bottom Panel
Drawer Support Rail
2
Drawer Front Panel(Big)
4
Drawer Side Panel(Big)
2
Drawer Back Panel(Big)
Front Bottom Rail
Left Back Top Rail
K
L
M
N
O
P
Q
R
S
Right Top Panel
Centre Panel
Right Front Top Rail
Middle Rail
1
1
Right Back Top Rail
1
1
Left Back Panel
Right Back Panel
2
1
1
1
1
Shelf
Bottom Panel
Foot
Door
DR1
DR3
DR4
Dream On Me Inc.
1532 S Washington Ave
Piscataway Township
NJ 08854
TEL: [phone]
Customer Care: [phone]

STEP 1
Connect front bottom rail (J) and back bottom rail (M) to
bottom panel (O) by using 1-5/8” wood dowel (e),cams (c)
and cam bolts (d).
Tighten all by phillips-head screwdriver.
Connect foot (P) to bottom panel (O) by using 2” screw (h).
12
a2-3/8” bolt
bbarrel nut 12
22
c
d
cams
cam bolts 22
32
e
f1-1/2” screw
1-5/8” wood dowel
27
g1-3/8” screw 10
h
knob 7
i
1” screw 7
j
allen wrench (for f)
allen wrench (for a&h)
1
k
1
1
46
m
n
o
plastic-strip
screw (for back panel)
tip over restraint
2
1
a b c d e
fg
no
p q rst
p
q
r
s
t
k m
h i j
REF. PART NAME QUANTITY
8
2
2
4
4
2” screw
5/8” screw
hinge 2
shelf pin
hinge 1
d
dd
d
e
e
ee
h
PHILLIPS--HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY ----NOT INCLUDE

3
STEP 3
Use allen wrench (q) to connect 2" screw (h).
Connect the assembled parts of STEP 1 to
centre panel (D) by using 1-5/8" wood dowel
(e) and 2" screw (h).
D
h
h
h
e
e
e
e
ee
e
Use allen wrench (q) to connect bolts.
Connect right front top rail (G) and right
back top rail (L) to centre panel (D) by
using 1-5/8” wood dowel (e),barrel nut
(b) and 2-3/8” bolt (a).
Connect right side panel
(E) to the assembled
parts by using 1-5/8”
wood dowel (e),barrel
nut (b) and 2-3/8” bolt
(a).

4
STEP 4
STEP 5
Use allen wrench (q) to connect bolts.
Connect left front top rail (F) and left
back top rail (K) to centre panel (D) by
using 1-5/8” wood dowel (e),barrel nut
(b) and 2-3/8” bolt (a).
Connect left side panel
(C) to the assembled
parts by using 1-5/8”
wood dowel (e),barrel
nut (b) and 2-3/8” bolt
(a).
e
e
e
e
Connect left top panel (A) to left side panel
(C) by using 1-5/8” wood dowel (e),cams (c)
and cam bolts (d).
Connect left front top rail (F) and left back top
rail (K) to left top panel (A) by using 1-5/8”
wood dowel (e) and 1-3/8" screw (g).
Tighten all by phillips-head screwdriver.
PHILLIPS--HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY ----NOT INCLUDE

STEP 7
STEP 6
Connect right top panel (B) to centre panel (D)
and right side panel (E) by using 1-5/8” wood
dowel (e),cams (c) and cam bolts (d).
Connect right front top rail (G) and right back
top rail (L) to right top panel (B) by using 1-3/8"
screw (g).
Tighten all by phillips-head screwdriver.
Connect left back panel (R) and right back panel (S) to
the back of the chest by using screw (s).
Tighten all by phillips-head screwdriver.
PHILLIPS--HEAD SCREWDRIVER
REQUIRED FOR ASSEMBLY
----NOT INCLUDE
5
r
R
R
S
s
s
s

STEP 8
Connect drawer side panel (DR2) to drawer front
panel (DR1) by using 1-1/2” screw (f).
Connect drawer support rail (DR5) to drawer
front panel (DR1) by using cams (c) and cam
bolts (d).
MAKE SURE the grooves line up and face inside.
LOCK cams (c) into drawer support rail (DR5) by
turning them.
USE allen wrench (p) to tighten 1-1/2” screw (f).
Assemble the Drawer.
DR1
c
d
Slide drawer bottom panel (DR4) into grooves of drawer front panel (DR1)
and drawer side panel (DR2) .
STEP 9
DR4
DR1
6

Connect the knob (n) to drawer front panel (DR1) by using 1” screw (o).
STEP 11
DR1
o
o
n
n
7
Connect drawer back panel (DR3) to drawer side
panel (DR2) and drawer support rail (DR5) by
using 1-1/2” screw (f).
TIGHTEN all by allen wrench (p).
ASSEMBLE the rest of drawers by repeating
STEP 8,9,10.
STEP 10
DR4
p
DR3

Slide the drawers into rails on left side panel (C) and centre panel (D).
NOTE: PLEASE PUT THE DRAWER WITH CLEAN STICKER AS THE TOP ONE.
STEP 12
8

9
STEP 13
STEP 14
PHILLIPS--HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY ----NOT INCLUDE
PHILLIPS--HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY ----NOT INCLUDE
Assemble hinge 1 (j) to right side panel (E) by using 5/8" screw (m).
j
j
m
m
m
m
m
mj
m
m
m
m
m
m
n
o
k
Assemble hinge 2 (k) to door (Q) by using 5/8" screw (m).
Connect the knob (n) to door (Q) by using 1" screw (o).
Tighten all by phillips-head screwdriver.

10
STEP 15
1 2 3
1 2 3
1
PHILLIPS--HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY ----NOT INCLUDE
Connect door (Q) to right side panel (E).