John Lewis Napoli 80310601 User manual

Please check the pack contents before attempting to assemble this product. A full checklist of compo-
nents is given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 45 MINUTES to assemble with 1 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you are missing some fittings please contact our spare parts helpline on 0330 005 9435.
Opening hours are 9am - 5pm Monday to Friday.
John L wis
tock Code: 80310601 - 80310602 - 80310603
Napoli b dsid ch st
Thank you for purchasing this Napoli bedside chest. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
PRE-ASSEMBLY PREPARATION
Please ensure instructions are read in full before attempting to assemble this product.
N c ssary Tools
Screwdriver
002030405060708090 00 020 30 40 50
023456
Ruler/tape
measure Small hammer
Eye protection
NAN 03/14
Page 1

Metal dowel x 22 Long cam lock x 2 Middle cam lock x 14
Wooden dowel x 26
30mm
12mm 18.5mm
10.5mm
Short cam lock x 6
30mm Screw x 8
11mm Euroscrew x 8
25mm Nail x 30
410mm runners x1
360mm runners x1
A B C
G
L
H
M
D E F
I
30mm Screw x 16
Nail guide x 1 Support foot x 4
S
X2
X1
Z2
Z1
Page 2
NAN 03/14
Fittings checklist

1
2
2
3
4
4
5
6
7
18
8
9
9
13
16
14
15
11
10
12
17
Page 3
NAN 03/14
Pa ts checklist

17
1
A
A
A
A
Page 4
Step by step assembly inst uctions
Step One
Attach 8x metal dowels (A) into the pre drilled holes on top panel (1) and bottom panel (17) as shown.
Use a screwdriver to turn fitting (A) clockwise to fix.
1.
NAN 03/14
C
C
C
E
E
2
C
C
A
Step Two
Attach 6x wooden dowels (E) into the pre drilled holes on side panel (2) as shown.
Place 4x cam lock (C) into the holes on side panel (2) as shown, arrow pointing towards the bolt.
Attach 2x metal dowels (A) into the pre drilled holes on side panel (2) as shown.
Use a screwdriver to turn fitting (A) clockwise to fix.
Repeat for the other side panel
1.
2.

C
E
E
5
C
C
E
E
3
B
B
B
Page 5
NAN 03/14
Step by step assembly inst uctions
Step Three
Attach 4x wooden dowels (E) into the pre drilled holes on rails (4) as shown.
Place 4x cam lock (C) into the holes on side panels (4) as shown, arrow pointing towards the bolt.
1.
2.
Step Four
Attach 4x wooden dowels (E) into the pre drilled holes on rails (3) (5) as shown.
Place 2x cam lock (C) into the holes on side panels (5) as shown, arrow pointing towards the bolt.
Place 2x cam lock (B) into the holes on side panels (3) as shown, arrow pointing towards the bolt.
1.
2.
3.
C
C
C
E
E
E
E
C
C
4
4

A
18
18
Top
Bottom
11,5 mm
18 mm
A
A
7
7
Bottom
Top
11,5 mm
18 mm
Page 6
Step by step assembly inst uctions
Step Five
Attach 2x metal dowels (A) into the pre drilled holes on one the two rail (18) as shown.
Attach 2x metal dowels (A) into the pre drilled holes on one the two rail (7) as shown.
1.
2.
NAN 03/14

Page 7
NAN 03/14
M
M
2
2
7
7
18
18
LH
RH
Top
Top
Bottom
Bottom
18 mm
11,5 mm
18 mm
11,5 mm
Step by step assembly inst uctions
Step Six
Fix rails (18) onto side panel (2) using 4x screw (M)
Pay attention to fix in the front part of side panel (2) the rail with the metal dowels fixed as shown.
Pay attention to the right position of rail (18) as shown.
Fix rails (7) onto side panel (2) using 4x screw (M)
Pay attention to fix in the front part of side panel (2) the rail with the metal dowels fixed as shown.
Pay attention to the right position of rail (7) as shown.
1.
2.

Page 8
NAN 03/14
4
4
2
1
A
2
2
LH
RH
3
5
2LH
2RH
1
2
1
A
Step by step assembly inst uctions
Step Seven
Attach rails (3) (4) (5) onto side panels (2) as shown. Ensure metal dowels (A) and wooden dowels (E) are
aligned correctly with the holes of matching parts before attaching.
Secure rails (3) (4) (5) to side panels (2) using a screwdriver to turn fitting (B) C) clockwise to fix.
1.
Step Eight
Attach top panel (1) onto side panels (2) as shown. Ensure metal dowels (A) and wooden dowels (E) are
aligned correctly with the holes of matching parts before attaching.
Secure top panel (1) onto side panels (2) using a screwdriver to turn fitting (C) clockwise to fix.
1.

2LH
2RH
17
1
2
A
Step by step assembly inst uctions
Step Nine
Attach bottom panel (17) onto side panels (2) as shown. Ensure metal dowels (A) and wooden dowels (E)
are aligned correctly with the holes of matching parts before attaching.
Secure bottom panel (17) onto side panels (2) using a screwdriver to turn fitting (C) clockwise to fix.
1.
Page 9
NAN 03/14
M
I
6
17
Step Ten
Position back panel (6) as shown
Attach 4x support foot (I) to bottom (17) with 8x screw(M).
1.
2.

H H
H H
Z2
Z2
Z1
X2
X2
X1
Important:
The cabinet MUST
be ‘square’ when the
back is attached.
F
G
6
F
Page 10
Step by step assembly inst uctions
Step Eleven
Attach back panel (6) onto back side of the unit using 30x nails (F), with the help of the nail guide (G).1.
Step Twelve
Fix runner parts (Z1) (Z2) (X1) (X2) through holes shown in the detail view using euroscrews (H).1.
NAN 03/14