StreamLight Nightfighter Series User manual

Operating
Instructions
N
ight
F
ighter
®
S
erieS
tL-2
®
S
erieS

English
OPERATING INSTRUCTIONS FOR STREAMLIGHT® NIGHTFIGHTER®
SERIES/TL-2® SERIES
Congratulations on the purchase of the Nightfighter®/TL-2® Series flashlight, a compact and
convenient little flashlight that is a powerhouse of performance. Proper care and use of this
product will provide years of dependable service.
BATTERY INSTALLATION/REMOVAL
1. Unscrew the tail cap and remove depleted batteries.
2. Insert batteries into barrel with the positive ends pointing toward the flashlight head.
3. Screw tail cap onto flashlight barrel and tighten.
WARNING: FIRE, EXPLOSION,
BURN HAZARD – USE ONLY RECOMMENDED LITHIUM BATTERIES
Inferior quality lithium batteries can cause fire, explosion, burns. We recommend the use of ONLY
Streamlight or Panasonic, Sanyo, Energizer or Duracell batteries in our products. Use of other
batteries or mixing brands and old and new batteries may risk leakage, fire, explosion and
serious personal injury. To further avoid this risk for any brand lithium battery, do not recharge,
misuse, short circuit, disassemble, improperly store or discard, expose to high temperatures.
WARNING: The Nightfighter® and TL-2® (Xenon) utilize a high wattage Xenon bulb that can get
very hot. Never place the flashlight face-down against a flat surface or against any flammable
object. To transport or store, turn off the flashlight and unscrew the tail cap 1/8” to minimize
the possibility of accidental activation.
GENERAL OPERATION
Nightfighter®, Nightfighter® LED
• Press the tail switch for momentary activation or twist the tailcap for steady “on”.
Nightfighter® X (Multi-function LED)
• High: From off, press and hold for momentary activation; twist tailcap to lock on.
• Strobe: From off, fast double press and hold for momentary activation; twist tailcap to lock
on.
WARNING - Use of light in “strobe” mode may cause seizure in persons with photosensitive
epilepsy.
• Low: From off, fast triple press and hold for momentary activation; twist tailcap lock
on.

TL-2® X (Multi-function LED)
• High: From off, press and hold for momentary activation; click the switch to lock on.
• Strobe: From off, fast double press and hold for momentary activation; click the switch to lock
on.
WARNING - Use of light in “strobe” mode may cause seizure in persons with photosensitive
epilepsy.
• Low: From off, fast triple press and hold for momentary activation; click the switch to lock on.
The Nightfighter® and TL-2® (Xenon) have an adjustable focus. Rotate the head to adjust the focus from a
long range, pinpoint beam to a wider, softer flood effect for close-up use. The Nightfighter® LED,
Nightfighter® X, TL-2® LED and TL-2® X models use LEDs “fixed” at optimum focus and are not adjustable.
BULB REPLACEMENT
LED models do not require bulb replacement. Do not attempt to change the LED in the
Nightfighter® LED, Nightfighter® X, TL-2® LED or TL-2® X.
The Xenon bi-pin bulb is designed to last through three (3) to five (5) sets of batteries in continuous use.
Intermittent use may produce less bulb life (due to repeated start up shock and higher voltage spikes).
Unscrew the flashlight head from the barrel and remove the bulb holder assembly. Always wear safety
glasses
and gloves. Never touch a hot bulb; allow it to cool before handling. Firmly grasp the burned out
bulb and pull it from the holder assembly. Grasp the replacement bulb and direct the pins straight into the
holes in the holder assembly until the bulb is firmly seated.
MAINTENANCE
Keep the O-ring area on the barrel lubricated.
TL-2®, TL-2® LED
• Press the tail switch for momentary activation or push and click the switch to lock on.
When it comes to quality work lights, Streamlight is the brand you can depend on.