Streamline ARCISAN Synergii SY04117 User manual

Synergii Toilet Suite
SY04117 (Slim Seat) and SY04127 (Standard Seat)
SY04118 (Slim Seat) and SY04128 (Standard Seat)
Installation Guide
www.streamlineproducts.com.au | Ph: 1300 735 352
This Synergii Bottom Inlet Toilet Suite is designed for
a left or right hand bottom inlet installation.
A 1/2” male thread will need to be plumbed in at the
location shown.
The standard set-out for a S-Trap is 80-200mm.
All distances are from final floor or finished wall.
The installer will need to supply the stop tap.
For bottom inlet the installer will also need to supply
the flexible hose for connection between the inlet and
the stop tap.
A 500mm length flexible hose will suit most installations
but the required length is dependent on the position of
the stop tap.
1
Back
Inlet
80-200
185
210
75
735
Optional elbow for set out 160-220mm (JT34)
Dimensions are in millimeters and are subject to manufacturing variations. Streamline reserves
the right to vary specications at any time without notice. Information provided within this
installation sheet is correct at the date of printing.
Version: 1.2 - March 2022
This product installation must comply to AS/NZS 3500.
B
A
210
min 210 min
200 max 200 max
Bottom
Inlet

NOTE:
If you have a bottom inlet cistern, follow instructions
on the top of page 3 (A).
If you have a back inlet cistern, follow instructions on
the bottom of page 3 (B).
1
Place the pan in
position ensuring
it is centred in
accordance with the
centre line of the outlet.
Mark location of pan xing bolts.
2
Remove pan, drill holes for xing bolts and attach brackets.
3
For S Trap installation, cut horizontal pipe to required length
and t seal. Attach wall xing kit to elbow, push elbow into
the pan collar and adjust to correct height. Fix to wall and
adjust to ensure the elbow is vertical.
4
Attach pan bolts, into holes, as shown.
6
Locate the pan in
the nal position.
Screw threads into
oor mount brackets.
55
7
Fit outlet seal to bottom of outlet mechanism. Do not place
outlet seal on pan and then sit cistern on top!
2
57mm
5
Ensure screws are centred when the cistern is placed on
the pan.

8
Remove inlet mechanism. Locate the cistern onto the pan.
Screw down tightly to ensure a seal between the bolt head
and the bottom of the cistern.
10
Check if the inlet valve is under normal operation and adjust
the inlet valve oat adjustment thumbscrew clockwise (for
higher oat & water level) or anticlockwise (for lower oat &
water level).
Screw inlet hose onto stop tap. Place inlet valve into position
within the cistern.
9
Back Inlet
8
Connect exible hose (not supplied) to inlet pipe at bottom
of cistern.
10
Join the inlet mechanism hose
to the thread and replace inlet
mechanism. Connect exible
hose to stop tap.
Bottom Inlet
9
Feed hose through hole in pan and locate the cistern onto the
pan. Screw down tightly to ensure a seal between the bolt
head and the bottom of the cistern.
3

4
Technical and Service - Ph: 1300 735 352 | Email: [e-mail]
11
Seat Install: Insert xing bolts into holes in the pan.
12
Push the plastic and metal washers as far down the screw as
possible, then nger tighten.
13 14
Once you have positioned the seat in the desired position, open
the lid and with an 8mm spanner, tighten the posts until the seat
is locked in place.
Push seat onto the posts and close lid. Move the seat around
until it is square with the pan.
Please leave the instructions with the owner.