Strong SRT 4300 User manual

1
一
Digital Satellite Receiver
USER’S MANUAL

2
Table of contents
Safety…………………………………………………………………………….……4
General Introduction………………………………………………………….…..…6
Front Panel / Rear Panel…………………………………………………………....8
Remote Control Unit………………………………………………………….……. 10
S.T.B Connection……………………………………………………………….......13
User Settings…………………………………………………………………...14
1. User Settings………………………………………………………………...14
1.1 OSD setting……………………………………………………….…...14
1.2 A/V output setting……………………………………………………………14
1.3 Local Time Setting………………………………………………………….14
1.4 Timer Setting………………………………………………………....15
1.5 Parental Control…………………………………………………………...15
2. Installation…………………………………………………………….………16
2.1 Antenna settintg……………………………………………………….………17
2.2 Satellite listt………………………………………………….………...17
2.3 Transponder list…………………………………………….……..….18
2.4 Setup Motor…………………………………………….……..….19
2.5 USALS Setup…………………………………………….……..….19
3. Channel Manager……………………………………….………..20
3.1 TV Channel dit……………………………………….………..20
3.2 Radio Channel Edit……………………………………….………..21

3
Table of contents
4. System……………………………………………………………………………..24
4.1 System Infornation……………………………………………....24
4.2 Factory Default………………………………………………………..…...….…24
5. USB ………………………………………………………………………………25
5.1 PVR Preview…………….………………………………………………………25
5.2 PVR Partition Select………………………………………………………25
5.3 USB Meida……………………………………………………………………26
5.4 USB Game………………………………………………………………………27
5.5 Software Update………………………………………………………………28
5.6 Database backup……….……………………………………………………28
PVR Instruction………………………………………………………………29
TIMESHIFT………………………………………………………………30
6. Games……………………………………………………………………………..31
6.1 Teris………………………………………………………………………………31
6.2 Snake……………………………………………………………………………31
Trouble Shooting………………………………………………………………….…32
Glossary……………………………………………………………….……………...33
Specification………………………………………………………………………….35

4
Safety Instructions
This STB has been manufactured to satisfy the international safety standards.
Please read the following safety precautions carefully.
MAIN SUPPLY
:AC 100/240V, 50/60Hz, 30W.
OVERLOADING
:Do not overload a wall outlet, extension cord or adapter as this may result
in fire or electric shock.
Ensure that the power source (socket) is easily accessible.
LIQUIDS
:This STB shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the STB.
CLEANING
:Disconnect the STB from the main supply before cleaning. Do not use any
kind of solvents to clean the STB, only use a soft-dry cloth.
VENTILATION
:The slots on top of the STB must be left uncovered to allow proper airflow
to the unit.
Ensure a minimum distance of 5cm around the apparatus for sufficient
ventilation.
Ensure that the ventilation is not impeded by covering the ventilation
openings with items such as newspapers, table-cloths, curtains, etc.
Do not stand the STB on soft furnishings or carpets.
Do not expose the STB to direct sunlight or do not place it near a heater.
Do not stack electronic equipments on top of the STB.
Do not place naked flame sources, such as lighted candles on the
apparatus.
ATTACHMENTS
:Do not use any unrecommended attachments as these may cause hazard
or damage to the STB.

5
Safety Instructions
CONNECTION TO THE SATELLITE DISH LNB
:Disconnect the STB from the main supply before connecting or
disconnecting the cable from the satellite dish.
FAILURE TO DO SO CAN DAMAGE THE LNB.
CONNECTION TO THE TV
:Disconnect the STB from the main supply before connecting or
disconnecting the cable from TV.
FAILURE TO DO SO CAN DAMAGE THE TV.
EARTHING
:The LNB cable MUST BE EARTHED to the system earth for the satellite
dish.
LOCATION
:Place the STB indoor in order not to expose to lightening , rain or Sunlight.
Use the apparatus only in moderate climates (not in tropical climates).
Battery handling
:Batteries may contain toxic agents that are hazardous to the environment.
Therefore, dispose of the batteries immediately according to the prevailing
statutory regulations. Never throw the batteries in normal household waste.

6
General Introduction
INTRODUCTION
This manual will help you learn basic functions such as installation, selecting
channels and many other functions of the STB. All functions can be operated by
the remote control. You can easily install it by selecting ”Installation” function
and upgrade its software through communication cable.
The remote control is designed for easy access to all the functions at once and
for comfortable grab for your hand. It is programmed to control all functions and
to easily watch TV and Radio programs via the STB.
WARNING
Any problems can be caused by the use of unofficial software. The use of
software versions other than dealers or distributors official software will void the
manufacturer’s warranty. It is advised that only the formal software released
from dealers or distributors should be used.

7
General Introduction
UNPACKING
Unpack the unit and check to make sure that all of the following items are
included in the packaging.
1 x Remote Control Unit (RCU)
1 x User Manual
2 x AAA batteries
1 x Digital Satellite Receiver
1 x A/V Cable
We hope you enjoy using your digital satellite receiver!

8
Front Panel/ Rear Panel
Front Panel
1 2 3 4
1 USB port, for connecting a USB storage device.
2 To switch the receiver between stand-by mode and po
wer-on mode.
3 To select the next channel, or next option in a menu.
4 To select the previous channel, or previous option in a
menu.

9
Front Panel/ Rear Panel
Rear Panel
No. Symbol Function
1 LNB INPUT Use to connect a satellite dish.
2 Y/Pb/Pr RCA
Component
Component connection (Y/Pb/Pr)
3 Video RCA Composite video connection
4 ANT IN Connect to Terrestrial Antenna through Modulator.
5 A/V RCA To connect the Audio/Video RCA output to TV.
6 LOOP OUT Loop-through output to VCR, etc.
7 RS-232 Use it when connecting to your PC.
8 A/V RCA To connect the Audio/Video RCA output to TV.
9 S/PDIF Digital audio output.
10 POWER Power ON/OFF switch.

10
\
Remote Control Unit

11
Remote Control Unit
1 To switches between power-on and stand-by modes.
2 0–9 To choose a channel directly,or to numeria information
a menu.
3 MULTI
PICTURES
MULTI –PICTURE
4 EPG To show the TV and radio program guide
5 MENU To display the main menu,or return to a previous menu.
6 VOL(◄/►) To change the volume in viewing mode,or to change an
p
tion or setting in a menu.
7 OK To show the channel list in viewing mode,and to select
an item(or confirm a choice) in a menu.
8 FAV To display the favourites list in viewing mode,and to
select a favourite
9 RECALL To return to the prebious channel or station
10 SAT To display SAT list.
11 ZOOM Press to Zoom-in and Zoom-out picture.
12 SLOW To show the playback of a movie
13 TXT
14 To fast rewind a movie or music track
15 To go to the start of a movie or music track,or show the
previous photo
16 To go to the end of a movie of music track ,or show the
next photo.
17 USB To display the USB list

12
Remote Control Unit
18 BOOK
MARK
19 MUTE To turns sound on or off.
20 TV/SAT Switch between TV and SAT mode.
( This function only valid to Terrestrial TV program that is
connected
and deliver by Modulator of this STB )
21 INFO To show information about the current program.
22 EXIT To close the current menu and return to normal viewing.
23 SUBTL To turn subtitles on or off.
24 PAGE
( / )
To move to the next page or previous page ( if there is
more than one page), or to zoom in or out
25 AUDIO To choose speakers (left,right of stereo),audio format
and audio language.
26 TV/RADIO To switches between TV and Radio (and vice versa)
27 PAUSE To freeze the screen
28 RECORD To start recording a movie
29 ►To start or pause a movie or music track
3
0 To fast forward in a movie or music track
31 To stop a movie or music track ,or to stop recording a
movie
32 TIMESHIFT
To Stop playing the USB Media

13
S.T.B Connection
Step 1: Connect to the antenna
Connect the satellite dish lead coming from the wall plate to the LNB INPUT
socket on the SRT 4300(socket1).
Step 2: Choose your Connection
There are a number of methods for connecting the SRT4300, depending on
your preference and the connection types on your TV. These methods are
labeled A, B below.
A: Y / Pb / Pr (Component) using the supplied RCA blue–red–green lead
For Component video, connect with the supplied Y / Pb / Pr Component cable
(green, blue and red leads). Connect the leads to the Y, Pb and Pr sockets on
the SRT4300, and then to the corresponding Component sockets on your TV.
Please pay attention to the color-coding. You will also need to establish a
connection for left and right audio via the audio sockets. This can be done using
the supplied RCA cable.
For right audio, connect the red RCA lead and for left audio, connect the white
RCA lead.
B: CVBS (Composite) using the supplied RCA red–white–yellow lead
Using the appropriate color-coding, you can connect to your TV with the
supplied RCA cable.
For video, connect the yellow RCA lead to the yellow video socket on the
SRT4300 and the corresponding socket on your TV.
For right audio, connect the red RCA lead to the red audio socket on the
SRT4300 and the corresponding socket on your TV.
For left audio, connect the white RCA lead on the SRT4300 and the
corresponding socket on your TV.
Various equipment and TV/VCR can be connected to STB.
This manual will explain common ways to connect to the equipment.
If you experience any problem, please contact your sales agency.

14
User Settings
Plug in the STB. Then press the “power” button on the remote control or the
“Standby” button on the STB Front Panel. The Main Menu screen, the
beginning of the OSD screen, will appear as shown in the following picture. The
Main Menu displays various functions of the STB or you can select with “CH”
buttons and the numeric buttons on the remote control. To proceed to the next
stage, press the “OK” button on the remote control.
Plug in the STB, and power on, there are foreign languages for your choice,
choose the one you prefer. Then please press “Menu” on the remote control to
get started,(default lock code: 0000).will
appear as shown in the following picture.
.1.1. OSD setting
Select the preferred languages and OSD
transparency.
1.2. A/V output setting
To set the basic specifications of your
STB
1.3. Local Time Setting
To set the local time and date to your STB, then save it.
Time Zone
Choose the time zone of your country
belong to.
Local Date
Set the Local Date.
Local Time
Set the Local Time.
Summer Time
If you set summer time to “ON”, then your
local time should add one hour more.
Date format
Choose the format to display the Date.

15
User Settings
1.4.Timer Setting
Timer Number
From 1 to 8, you can set total 8 different
Timers
Timer Set
To open or close each Timer, if the Timer
Set is off, then you can not continue to set
Timer.
Timer Control
There are total 3 types of Timer type: Start time only; Stop time only; Both on.
Repeat Mode
There are 3 types of Repeat Mode: one time, week(1-5), week(6-7).
Start time :
To set STB power on time.
Stop time :
To set STB power off time.
Channel
To select the channel what you want .
TV/RADIO
To shift between TV or radio.
1.5. Parental Control
To prevent the unauthorized Accessing of
your STB, you can set the Parental
control password to you receiver. (Default
password: 0000)
Channel Manager Lock: To lock the
Channel Edit menu to prevent
unauthorized adjusting of Channel.
Installation Lock: To lock the installation
menu to prevent unauthorized adjusting of Installation.

16
User Settings
System Setting Lock: To lock the System Setting menu to prevent unauthorized
adjusting of System Setting.
Channel Lock: To lock the channels to prevent the channels that are not suitable
for Children.
Receiver Lock: To lock the receiver to prevent from unauthorized watching.
Factory Default Lock: To lock the Factory Default menu to prevent unauthorized
operation.
You can also change the password by input numeric key for NEW Password,
and then repeat again to VERIFY Password.

17
Installation
2. Installation
Your STB can be easily installed by using
“Installation” Menu.Press the VOL move
to installation.
2.1.Antenna setting
Selecting your installed Satellite on the
right side, and press “Vol+” button to
enter into left side, then set all the other
figures such as LNB type;LNB low,LNB
high,Tp,DiSEqc; 22KHz; DiSEqC control; LNB Power and so on, using the ”Vol”
buttons on the remote control then press yellow button to save the settings.
ALL + NIT: To Search out all the Free
Channels + Scrambled Channels
available in particular Satellite or
Transponders including the new
transponders that are not
preprogrammed in your STB but
broadcasting by Satellite Provider.
Then press ”OK” button to start searching,
while the related menu shows a details
info of the scanning status.
2.2 Satellite list
Add satellite
Press the yellow button to add the new
Satellite to this STB.
Edit satellite
In this menu, you can view the satellite
information, and edit the satellite by
Rename and Modify Using the “Vol” or

18
Installation
numeric buttons.
Rename
To change the name of the Satellite
Modify
To modify the longitude and direction of
the Satellite
Delete satellite
Press the yellow button to delete the
Satellite from this STB forever.
Muti satellite search
Press the yellow button to select the
satellite name then scan button to select the scan mode “ALL,FTA,CAS”and
pree OK button ,the scanning will beginning.
Blind scan
2.3.Transponder list
You can edit with various option choices of transponder specifications and
settings, also you can easily manually search a single transponder by selecting
SCAN.
Add TP
Press yellow button to add a TP.
Input the frequency value and symbol rate
value by numeric key, choose the correct
Polarization, Horizontal or Vertical, then
save it.
Edit TP
Press the yellow button you can edit the
current TP. Input the frequency value

19
Installation
and symbol rate value by numeric key, choose the correct Polarization,
Horizontal or Vertical, then save it.
Delete TP
Press yellow button you can delete the channel you do want to view.
2.4 Setup Motor
To set up the auto Satellite Dish (DiSEqC1.2 system) and generate the
positioner system.
Continuously Move
Using the ”Vol” buttons to adjust West
and East to move the dish, the signal and
quality bars at the bottom of the screen
judge the best position of the dish.
Step Size
Adjust the Move Step from 1 to 10.
Move steps
Dish move step by step, adjust the dish to
the best position.
Limit set
Using the ”Vol” buttons to fix East or West limit or disable limit status.
2.5 USALS Setup
To set up the USALS system onto your STB.
If you have a USALS motorized system, you must set your position (latitude and
longitude) in order to calculate all motor positions for viewable satellites. You
should refer to the motor’s manual .
Set the correct value of Longitude and Latitude of your position, press OK key,
then you can see the moving direction and angle to your selected satellite from
Motor menu.

20
Channel Manager
3.1 TV Channel dit
You can easily access to any TV and
Radio programs by the variable functions
available from this STB, and enjoy your
digital entertainment TV fun.
3.1.1 Edit channel
Press Red button, then you can use the
color buttons to Rename, Modify and
Lock the channels.
Rename: Press Red button, you can change the name of selected channel.
Modify: Press yellow button, you can re-set PID settings of selected channel by
numeric key.
Lock: Press OK button to select the channel you wish to Lock, then press blue
button, you can lock the selected channel from authorized watching.
Return: Press red button, you can return to previous menu.
3.1.2 Delete channel
Press red button to select the channel
you wish to delete, then press yellow
button to delete the selected channel
from STB.
3.1.3Move channel
Press red button to select the channel
you wish to move, then press yellow
button to pop-up Move-To menu and input
channel numbers you wish to move, and
press OK button again to insert.