Struers LaboForce-1 User manual

Manual No.: 15277001
Date of Release .08.2012
LaboForce-1
Instruction Manual

LaboForce-1
Instruction Manual
Always state Serial No and Voltage/frequency if you have technical questions or when ordering spare parts.
You will find the Serial No. and Voltage on the type plate of the machine itself. We may also need the Date
and Article No of the manual. This information is found on the front cover.
The following restrictions should be observed, as violation of the restrictions may cause cancellation of
Struers legal obligations:
Instruction Manuals: Struers Instruction Manual may only be used in connection with Struers equipment
covered by the Instruction Manual.
Service Manuals: Struers Service Manual may only be used by a trained technician authorised by Struers.
The Service Manual may only be used in connection with Struers equipment covered by the Service Manual.
Struers assumes no responsibility for errors in the manual text/illustrations. The information in this manual is
subject to changes without notice. The manual may mention accesso
ries or parts not included in the present
version of the equipment.
Original instructions. The contents of this manual is the property of Struers. Reproduction of any part of
this manual without the written permission of Struers is not allowed.
All rights reserved. © Struers 2012.
Struers A/S
Pederstrupvej 84
DK-2750 Ballerup
Denmark
Telephone [phone]
Fax [phone]

LaboForce-1
Instruction Manual
LaboForce-1
Safety Precaution Sheet
To be read carefully
before use
1. The operator should be fully aware of the use of the machine according
to the Instruction Manual. The machine must be mounted securely on
the grinding/polishing machine.
2. Be sure that the actual voltage corresponds to the voltage stated on the
back of the machine. The machine must be earthed.
3. Blue lubricant: follow the current safety rules for handling, mixing, filling,
emptying and disposal of the alcohol-based lubricant.
4. If you observe malfunctions or hear unusual noises - stop the machine
and call technical service.
The equipment should only be used for its intended purpose and as detailed in the Instruction Manual.
The equipment is designed for use with consumables supplied by Struers. If subjected to misuse, improper
installation, alteration, neglect, accident or improper repair, Struers will accept no responsibility for
damage(s) to the user or the equipment.
Dismantling of any part of the equipment, during service or repair, should always be performed by a qualified
technician (electromechanical, electronic, mechanical, pneumatic, etc.).

LaboForce-1
Instruction Manual
Disposal
Equipment marked with a WEEE symbol contain electrical and
electronic components and must not be disposed of as general
waste.
Please contact your local authorities for information on the correct
method of disposal in accordance with national legislation.

LaboForce-1
Instruction Manual
1
User’s Guide
Table of Contents Page
1.Getting Started
Checking the Contents of Packing.....................................................2
Getting Acquainted with LaboForce-1................................................2
Setting up LaboForce-1......................................................................3
Adjusting the Specimen Mover Position.............................................3
Distance to Preparation Disc ....................................................3
Connecting LaboForce-1....................................................................4
Supplying Power.......................................................................4
Communication.........................................................................4
Mounting a Drip Lubricator.................................................................5
Mounting a LaboDoser Dosing Unit ...................................................5
2.Operation
Inserting a Specimen .........................................................................6
Adjusting the Force............................................................................6
Operating LaboForce-1......................................................................7
Replacing the Specimen Mover Plate................................................7
Operating a Drip Lubricator................................................................8
Changing Lubricant............................................................................8

LaboForce-1
Instruction Manual
2
1. Getting Started
In the packing box you should find the following parts:
1 LaboForce-1
1 Allen-key 3 mm
2 Extra screws M4 for securing the specimen mover plate
1 Nut, M16
3 Washers, 1 mm for levelling of column height
1 Washer, 3 mm for levelling of column height
1 Set of Instruction Manuals
Take a moment to familiarise yourself with the location and
names of the LaboForce-1 components.
Handle
Distance adjustment screw
Force adjustment screw
Release button
Thrust pad
Specimen mover plate
Checking the Contents of
Packing
Getting Acquainted with
LaboForce-1

LaboForce-1
Instruction Manual
3
LaboForce-1 is prepared to be mounted on Struers
grinding/polishing machines, LaboPol-1, -2, -4, -5, -6, -21 or -25.
Remove the plastic lid from the pre-punched hole for the
LaboForce column. Turn the LaboPol machine onto its left-
hand side.
Lead the LaboForce-1 column through the hole. Mount and
tighten the bottom nut using a 24 mm spanner.
Raise the LaboPol machine to upright position.
Go to paragraph Adjusting the Specimen Mover Position.
Remove the plastic lid from the pre-punched hole for the
LaboForce column. Move LaboPol to the left so that the part
of the machine where LaboForce-1 is to be mounted is free of
the table.
Lead the LaboForce-1 column through the hole. Mount and
tighten the bottom nut using a 24 mm spanner.
Move LaboPol back onto the table.
Go to paragraph Adjusting the Specimen Mover Position.
To ensure correct working conditions for LaboForce-1 you need to
adjust the actual distance between the specimen mover plate and
the preparation disc of your grinding/polishing machine.
Place the specimen mover plate on the shaft and secure it
with the screw.
Remove the plastic cap on top of LaboForce-1, insert the
Allen-key and turn it clockwise until LaboForce-1 is in top
position.
Mount a grinding or polishing disc on the LaboPol and swing
LaboForce-1 into correct position over the disc.
Press LaboForce-1 down and adjust the distance between
grinding or polishing disc and specimen mover plate to about
1.5 - 2 mm by turning the Allen-key counter clockwise.
If the distance is too small you must:
−Remove LaboForce-1 from the grinding/polishing
machine.
−Attach 1 or more additional washers (1-3 mm). Grease
the washers and fasten them under the column, using the
grease as an adhesive.
−Mount LaboForce-1 in its hole again and tighten the
bottom nut.
Finally mount a counter nut to ensure that the column
remains in the correct position.
Setting up LaboForce-1
On LaboPol-1/-2/-4/-5
On LaboPol-21/-25
Adjusting the Specimen Mover
Position
Distance to Preparation Disc
Repeat the above procedure until the correct distance is achieved.

LaboForce-1
Instruction Manual
4
Connect the power cable to the socket on the back of the
LaboPol machine.
To let the LaboPol know that a LaboForce-1 is connected, the
communications plug attached to the power cable has to be
connected to the socket on the back of LaboPol.
Connecting LaboForce-1
Supplying Power
IMPORTANT
Check that the mains voltage corresponds to the voltage stated on the type
plate on the back of the machine.
Communication

LaboForce-1
Instruction Manual
5
A drip lubricator can be mounted on the LaboForce-1 to supply
the necessary lubricant during the preparation process.
Remove the drip lubricator from its box.
Loosen the finger screw underneath LaboForce-1.
Guide the bottom plate of the drip lubricator onto the finger
screw and the positioning pin underneath the LaboForce-1,
and re-tighten the finger screw.
Hold the lubricant bottle with one hand and remove the lid.
Fill the bottle with lubricant.
Replace the lid and the drip lubricator is ready to use.
Follow the Instructions for Use that are supplied with the Dosing
Unit.
Mounting a Drip Lubricator
(Accessory)
Mounting a LaboDoser Dosing
Unit (Accessory)

LaboForce-1
Instruction Manual
6
2. Operation
Lift the thrust pad on the adjustment screw to make room for
the specimen.
Place the specimen in one of the holes of the specimen mover
plate and lower the thrust pad.
Adjust the force by turning the adjustment screw .
The marks on the spring loaded screw correspond to the
actual force in Newton as stated below:
Inserting a Specimen
Tip
For quick positioning of the adjustment screw (e.g. for specimens of
differing heights), press the release button and move the screw up or down.
Adjusting the Force
Indication Force
0 0 N
1 2.5 N
2 5 N
3 7.5 N
4 10 N
5 12.5 N
6 15 N
7 17.5 N
8 20 N
WARNING
If less than three specimens are prepared, ensure that the unused pressure
feet do not touch the preparation surface.
Thin mark
Thick mark

LaboForce-1
Instruction Manual
7
Press LaboForce-1 down and turn it into the correct position
over the grinding or polishing disc.
Secure LaboForce-1 in that position by locking the handle
Place 1 to 3 specimens in the specimen mover plate.
Adjust the force.
Adjust the lubricant dosing level.
Press START on LaboPol.
Perform the method step and press STOP on LaboPol.
Stop lubricant dosing:
Drip Lubricator: Close the valve on the drip lubricator
LaboDoser: Stops automatically after the pre-set time.
As specimens must fit the holes in the specimen mover plate
quite accurately, the specimen mover plate has to be
replaced when samples of another size have to be prepared.
Unlock LaboForce-1 and let it move into top position.
Turn LaboForce-1 to the left over the edge of the LaboPol.
Unscrew the fastening screw of the specimen mover plate.
Place the new specimen mover plate on the column and secure
it with the screw.
Lower LaboForce-1 again and lock the handle.
Operating LaboForce-1
Important
The specimens should run close to the edge of the grinding/polishing disc.
The distance should be about 2 mm.
Remember
LaboForce-1 will start rotating as soon as LaboPol is switched on unless the
switch “specimen mover” on the back of LaboPol has been switched off.
Replacing the
Specimen Mover Plate

LaboForce-1
Instruction Manual
8
Position the dosing nozzle in the correct position over the
preparation disc.
Open the valve and adjust the lubricant dosing level.
After completion of the preparation close the valve again to
stop lubricant dosing.
Remove the drip lubricator from LaboForce-1.
Hold the lubricant bottle firmly and remove the top lid.
Pour out the lubricant, and fill the bottle with a mild soap
solution.
Open the valve to clean the tube.
Exchange the soap solution with clean water and repeat the
above procedure.
Empty the lubricator.
Put the lubricator back on LaboForce-1 and tighten the finger
screw.
Refill with lubricant and mount the lid.
Follow the Instructions for Use that are supplied with the Dosing
Unit.
Operating a Drip Lubricator
(Accessory)
Changing Lubricant
Drip Lubricant
(Accessory)
LaboDoser Dosing Unit
(Accessory)

LaboForce-1
Instruction Manual
9
Reference Guide
Table of Contents Page
1.Accessories ...........................................................................10
2.Struers Metalog Guide™ ....................................................11
3.Maintenance
Every Day.........................................................................................12
Every Week......................................................................................12
4.Trouble-Shooting..................................................................13
5.Technical Data......................................................................14

LaboForce-1
Instruction Manual
10
1. Accessories
Please refer to the LaboForce brochure for details of the range
available.
Remember...
Struers offers a comprehensive range of consumables for grinding and
polishing. Please ask for separate leaflets.

LaboForce-1
Instruction Manual
11
2. Struers Metalog Guide™
LaboForce-1 is designed for preparation of most materials. In
Struers Metalog Guide™ you will find a detailed description of
grinding/polishing methods for automated mechanical specimen
preparation.
Struers Metalog Guide™ offers preparation methods for the most
common materials, based on a simple analysis of two key
properties: hardness and ductility. Finding the right method is
easy, including choice of consumables. Always consult Struers
Metalog Guide™ on the Struers website for the correct
preparation method for the actual specimens.
Metalog Guide™
A complete guide to materialographic specimen preparation.
www.struers.com/KNOWLEDGE/Metalog Guide.

LaboForce-1
Instruction Manual
12
3. Maintenance
Clean the specimen holder plate with a damp cloth.
Clean LaboForce-1 with a damp cloth.
Remove the drip lubricator from LaboForce-1.
Hold the lubricant bottle firmly and remove the top lid.
Pour out the lubricant, and fill the bottle with a mild soap
solution.
Open the valve to clean the tube.
Exchange the soap solution with water and repeat the above
procedure.
Empty the lubricator.
Put the lubricator back on LaboForce-1 and tighten the finger
screw.
Refill with lubricant and remount the lid.
Follow the Instructions for Use that are supplied with the Dosing
Unit.
Every Day
Every Week
Cleaning a Drip Lubricator
Cleaning a LaboDoser Dosing
Unit

LaboForce-1
Instruction Manual
13
4. Trouble-Shooting
Error Cause Action
The specimen mover
plate on LaboForce-1
does not start turning.
The switch for the specimen mover on the
back of LaboPol is set to “off”. Set the switch to “on”.
The specimen mover
plate runs unevenly or
stops.
Force too high. Reduce the force.
The column of
LaboForce-1 starts
turning.
Bottom nut of column is loose. Immediately tighten the nut
at the base of column (See
Section INSTALLATION).

LaboForce-1
Instruction Manual
14
5. Technical Data
Subject Specifications
Motor output 0.5 W
Torque at disc Continuous 0.5 Nm
Amperage
The motor is equipped with a thermal
switch for protection against overload.
16 mA/220-240 V
32 mA/100-120 V
Rotational speed 8/9.5 rpm at 50/60 Hz
Force per specimen Min. approximately 2 N, max. approx. 20 N
Safety Standard Please refer to the Declaration of Conformity
Noise Level 46 dB (A) at idle running, at a distance of 0.25m/10” from the machine
Power Supply LaboForce-1 is connected directly to LaboPol
Dimensions and
Weight Width 190 mm/7.5” (including drip lubricator)
Depth 265 mm/10.5”
Height 295 mm/11.6” (above grinding/polishing disc)
Weight 5.9 kg/13 lbs

LaboForce-1
Instruction Manual
15
Quick Reference
Lift the thrust pad to make room for the specimen.
Place the specimen in the specimen holder plate hole and
lower the thrust pad. Make sure that the specimen diameter
fits the specimen holder plate hole.
Adjust the force by turning the adjustment screw.
Stop the grinding/polishing machine.
Unlock the LaboForce-1 handle and let it move into top
position.
Change the disc on the turntable.
Lower LaboForce-1 again and lock the handle.
Lower LaboForce-1 and lock the handle.
Place 1 to 3 specimens in the specimen holder plate on the
chosen surface.
Adjust the lubricant dosing level.
Press START on LaboPol.
Perform the method step and press STOP on LaboPol.
Stop lubricant dosing
Drip Lubricator: Close the valve on the drip lubricator
LaboDoser: Stops automatically after the pre-set time.
Inserting a Specimen
Replacing a
Grinding/Polishing Disc
Starting a Preparation Step