Stryker The Go BED FL17E User manual

TECHNICAL ASSISTANCE AND PARTS
1 800 428-5025 (Service in English in Canada)
1 800 361-2040 (Service in French in Canada)
1 800 327-0770 (In United States)
E-mail (Canada): [e-mail]
December 2000
Manufactured by Stryker Bertec Medical Inc 72-0171 R1.0
Printed in Canada
OPERATIONS MANUAL
The GO BED
ELECTRIC ACUTE CARE BED
Product Number: FL17E
Product Number for the United States: 2500
TM

TABLE OF CONTENTS
3
1. INTRODUCTION.......................................................................................................................................5
1.1 BED SPECIFICATIONS ..................................................................................................................5
1.2 TECHNICAL SUPPORT..................................................................................................................5
1.3 WARNING / CAUTION / NOTE DEFINITIONS ...............................................................................6
1.4 SAFETY TIPS AND GUIDELINES ..................................................................................................6
1.5 WARRANTY ....................................................................................................................................8
Limited Warranty.............................................................................................................................8
To Obtain Service and/or Parts ......................................................................................................8
Return Authorization.......................................................................................................................8
Damaged Merchandise...................................................................................................................8
1.6 BED CLEANING AND MATTRESS CARE......................................................................................8
Cleaning Beds.................................................................................................................................8
Bed Mattress Care..........................................................................................................................9
1.7 BED POSITION PICTOGRAMS......................................................................................................9
1.8 BED ILLUSTRATION.....................................................................................................................10
2. BED OPERATION GUIDE......................................................................................................................11
2.1 SWITCHING ON POWER (ON/OFF SWITCH).............................................................................11
2.2 APPLYING THE BRAKE ...............................................................................................................11
2.3 MOVING THE BED........................................................................................................................11
Steer Pedal Operation..................................................................................................................12
Moving the Bed in a Straight Line.................................................................................................12
Moving the Bed in All Direction (Full Mobility) ..............................................................................12
2.4 FOLEY BAG HOOK USAGE.........................................................................................................12
2.5 FOOT PROP USAGE....................................................................................................................13
2.6 FRACTURE FRAME USAGE........................................................................................................13
2.7 PATIENT RESTRAINT STRAP LOCATIONS ...............................................................................13
2.8 CPR EMERGENCY RELEASE (OPTIONAL) USAGE..................................................................13
2.9 NIGHT LIGHT (OPTIONAL) USAGE.............................................................................................14
2.10 NURSE CALL (OPTIONAL) USAGE.............................................................................................14
2.11 120V AUXILIARY POWER OUTLET USAGE...............................................................................14
2.12 POSITIONING SIDE-RAILS..........................................................................................................14
2.13 HEAD AND FOOT BOARDS.........................................................................................................15
Removing Boards .........................................................................................................................15
Replacing Boards .........................................................................................................................15
Fixing Boards Permanently...........................................................................................................15
2.14 SIDE-RAIL FUNCTION GUIDE.....................................................................................................16
2.15 FOOT BOARD CONTROL PANEL GUIDE...................................................................................17
Lock-out Switches.........................................................................................................................17
Fowler Control Switches...............................................................................................................17
Knee Gatch Control Switches.......................................................................................................17
Hi-Lo Switches..............................................................................................................................18
Trendelenburg Switch...................................................................................................................18
Auto Contour (optional equipment) Pictogram .............................................................................18

N
NO OT TE E
Stryker Bertec gives special attention to the quality of the information found in this document. Any
comments on its content will be most welcomed. Please forward your remarks to our Technical Service
department (see section 1.2).
3. ACCESSORIES......................................................................................................................................19
3.1 IV POLE.........................................................................................................................................19
Installing the Permanently Attached I. V. Pole .............................................................................19
3.2 PENDANT CONTROL USAGE .....................................................................................................20
Installing a Pendant Control..........................................................................................................20
3.3 PATIENT HELPER SYSTEM USAGE...........................................................................................21
Installation of the Patient Helper System......................................................................................21
3.4 MATTRESS SUPPORT EXTENSION USAGE.............................................................................22
Installing the Mattress Support and Mattress Extensions.............................................................22
3.5 BED CRADDLE USAGE................................................................................................................23
Installing a Bed Cradle..................................................................................................................23
3.6 TRANSPORTATION CART OPERATION.....................................................................................23
Installing the Transportation Cart..................................................................................................23
3.7 FLIP TYPE BED SHELF USAGE..................................................................................................24
Installing the Shelf on the Bed......................................................................................................24
Storing the shelf............................................................................................................................24
3.8 OXYGEN BOTTLE HOLDER USAGE...........................................................................................25
Installing the Oxygen Bottle Holder ..............................................................................................25
3.9 SIDE-RAIL PAD USAGE...............................................................................................................25
Installing the Side-rail Pads ..........................................................................................................25
3.10 CHART HOLDER USAGE.............................................................................................................26
3.11 EMERGENCY CRANK USAGE ....................................................................................................26
Manual Operation of the Bed........................................................................................................26

Introduction Chapter 1
5
1. INTRODUCTION
This operations manual is designed to assist you with the operation of the GO BED. Before
operating the bed, it is important to read and understand all information in this guide. Hospital
staff should be able to refer to this guide at all time when using the bed.
A maintenance guide, included in the Customer’s Guide, is also available to assist you with the
servicing of the bed.
This operations manual is an integral part of the bed and should be turned over to the new user
should the bed be sold or transferred.
1.1 BED SPECIFICATIONS *
Maximum Weight Capacity 500 lb including 100 lb of boards and
accessories
227 kg including 45.5 kg of boards and
accessories
Overall Bed Length/Width -Steel Side-rails
Overall Bed Length/Width -Plastic Side-rails
93" x 41 9/16" (steel side-rails up)
93" x 38 3/8" (steel side-rails down)
236.2 cm x 105.5 cm (steel side-rails up)
236.2 cm x 97.5 cm (steel side-rails down)
93" x 42 9/16" (plastic side-rails up)
93" x 38 3/4" (plastic side-rails down)
236.2 cm x 108.1 cm (plastic side-rails up)
236.2 cm x 98.4 cm (plastic side-rails down)
Overall Weight (w/o boards and accessories) 385 lb -175 kg
Patient Sleeping Surface 35" x 80" extendable to 82" -84"
89 cm x 203 cm extendable to 208 -213 cm
Minimum/Maximum Bed Height 14" to 29" -35.5 cm to 74.7 cm
Sound Level <58 dBa
Fowler Angle 0° to 65°
Knee Gatch w/o Contour Positioning
Knee Gatch w/Contour Positioning 0° to 32° 0° to 24°
Trendelenburg/Reverse Trendelenburg -14° to +14°
Electrical Requirements -All electrical
requirements meet the CSA standard C22.2
No 125 and UL 544 specifications for Class
2G
100 VAC, 50-60 Hz, 7.5 A
120 VAC, 50-60 Hz, 9.8 A w/o outlet
120 VAC, 50-60 Hz, 14.8 A w/outlet
200 VAC, 50-60Hz, 3.2 A
220 VAC, 50-60 Hz, 2.9 A
240 VAC, 50-60 Hz, 2.7 A
* Stryker Bertec Medical affords special attention to product improvement and reserve the right to change specifications
without notice.
1.2 TECHNICAL SUPPORT
For questions regarding this product, contact one of the following Technical Service
departments or your local representative:
In Canada: In the United States:
Stryker Bertec Medical Inc Stryker Medical
Service in English: 1 800 428-5025 1 800 327-0770
Service in French: 1 800 361-2040 6300, Sprinkle Road
E-mail (Canada): [email protected] Kalamazoo, MI 49001-9799
70, 5th Avenue, P.O. Box 128 USA
L’Islet (Québec), G0R 2C0, Canada

Chapter 1 The GO BED Operations Manual
6
W
W
A
A
R
R
N
N
I
I
N
N
G
G
1.3 WARNING / CAUTION / NOTE DEFINITIONS
The words WARNING, CAUTION and NOTE carry special meanings and should be carefully
reviewed.
The personal safety of the patient or user may be involved. Disregarding this information could
result in injury to the patient or user.
These instructions point out special procedures or precautions that must be followed to avoid
damaging the equipment.
N
NO OT TE E
Notes provide special information to make maintenance easier or important instructions clearer.
1.4 SAFETY TIPS AND GUIDELINES
The following is a list of safety precautions that must be observed when operating or servicing
the GO BED. They are repeated throuhout the guide, where applicable. Carefully read and
strictly follow them before operating or servicing this unit.
•The GO BED is not intended for pediatric use.
•It is important that all users have been trained and educated on the inherent hazards
associated with the use of manual and electric beds. Bed mechanisms can cause serious
injury to the patient or user. Operate bed only when all people are clear of the mechanisms.
•This bed is equipped with a hospital grade plug for protection against shock hazard. It must
be plugged directly into a properly grounded receptacle. Grounding reliability can be
achieved only when a hospital grade receptacle is used.
•Possible fire hazard exists when this bed is used with oxygen administering equipment other
than nasal, mask type or half bed-length tent type. It is recommended to disconnect the bed
in such circumstances. When using a half bed-length tent type, ensure the side-rails are
outside the oxygen tent and oxygen tent should not extend below the mattress support level.
•Always keep the caster brakes applied when a patient is on the bed (except during
transport). Serious injury could result if the bed moves while a patient is getting in or out of
ed. After the brake pedal is applied, push on the bed to ensure the wheels are locked.
•To help reduce the number and severity of falls by patients, always leave the bed in the
lowest position and side-rails fully up when the patient is unattended. After raising a side-
rail, pull firmly on the side-rail to ensure it is securely locked into position.
•Always keep side-rails in the fully raised position and the sleeping surface horizontal in its
lowest position when the patient is sleeping unless the patient's medical conditions dictates
otherwise. If the sleeping surface is not in a horizontal position and the bed is equipped with
half-length side-rails, it is strongly recommended that only the head side-rails be kept in their
highest position and the foot side-rails be stored on the side of the bed to avoid the risks of a
patient becoming caught between the two side-rail sections.
W
W
A
A
R
R
N
N
I
I
N
N
G
G
C
C
A
A
U
U
T
T
I
I
O
O
N
N

Introduction Chapter 1
7
•Side-rails, with or without their padded covers or nets, are not intended to serve as restraint
devices to keep patient from exiting the bed. Side-rails are designed to keep a patient from
inadvertently rolling off the bed. It is the responsibility of the attending medical personnel to
determine the degree of restraint necessary to ensure a patient will remain safely in bed.
Failure to utilize the side-rails properly could result in serious patient injury.
•When a patient's condition requires greater safety measures for his security, use the lock-
out switches in the foot board control panel to deactivate the side-rail or pendant control
commands and install protective pads on the side-rails.
•When the sleeping surface sections are articulated, ensure that all spaces created by the
raised side-rails are clear in order to avoid the patient's limb becoming trapped between
side-rails or between side-rails and boards.
•When moving the bed with a patient in it, ensure that the bed is in the lowest position with
side-rails fully raised and securely locked in order to reduce risks of injuries to the patient.
•Do not attempt to move the bed directly sideways with the 5th wheel activated. The 5th
wheel can not pivot. Attempting to do so may cause injury to the patient or user.
•The instant CPR release is for emergency use only. When activating the CPR release, all
people and equipment must be removed from the area below and around the head and foot
sections of the bed or serious personal injury or damage to equipment could occur.
•When large fluid spills occur in the area of the circuit board, cables and motors, immediately
unplug the bed. Remove the patient from the bed and clean up the fluid. Have maintenance
completely check the bed. Fluids can have an adverse effect on operational capabilities of
any electrical product. DO NOT put the bed back into service until it is completely dried and
has been thoroughly tested for safe operation.
•Do not steam clean, hose off or ultrasonically clean the bed. Do not immerse any part of the
bed. The internal electrical parts may be damaged by exposure to water. Hand wash
regularly all surfaces of the bed with warm water and a mild detergent. Wipe cleaned
surfaces dry to avoid build up of cleaning substance. Inspect the mattress after each use.
Discontinue use if any cracks or rips are found in the mattress cover which may allow fluid to
enter the mattress. Failure to properly clean mattress or dispose of defective mattress will
increase the risk of exposure to pathogenic substances which may cause injury to the
patient or user.
•Always unplug the bed power cord from the wall outlet when cleaning or servicing the bed.
When working under the bed with the bed in the high position, always place blocks under
the frame and lock the casters to prevent injury in case the "Bed Down" switch is
accidentally pressed.
•When using the emergency crank during a power failure, unplug the power cord from the
wall receptacle so that unexpected resumption of power will not rotate handle. Remove and
store the crank before reconnecting the bed.
•Ensure that any bed malfunction is promptly reported to service personnel for immediate
attention. Preventive maintenance should be performed periodically to ensure all bed
features are functioning properly.
•Never move the bed using the raised side-rails nor hit the side-rails against any object found
in the room, for example: other furniture, walls, door frame, etc. Damage to the equipment
could result from such actions. Use the push/pull handles integrated on the head and foot
boards to move the bed, they provide a solid grip when moving the bed.
C
C
A
A
U
U
T
T
I
I
O
O
N
N

Chapter 1 The GO BED Operations Manual
8
1.5 WARRANTY
Limited Warranty
All Stryker Bertec products are guaranteed against material or manufacturing defects, improper
operation of mechanisms, and premature wear of bed components under normal use
conditions.
For questions regarding warranty, please contact Stryker Bertec Technical Service department
(see section 1.2) or your local representative.
To Obtain Service and/or Parts
For an on-site diagnosis and/or repair of a bed malfunction by a Stryker Field Service
Representative or to order replacement parts (see section 1.4, "To Order Parts" in the GO BED
Maintenance Manual), simply contact Stryker Bertec Technical Service department or your local
representative.
Return Authorization
Merchandise cannot be returned without approval from the Stryker Bertec Technical Service
department. An authorization number will be provided which must be clearly printed on the
returned merchandise. Stryker Bertec reserves the right to charge shipping and restocking fees
on returned items.
Damaged Merchandise
Claims for damaged merchandise must be made with the carrier within fifteen (15) days of
receipt of merchandise. DO NOT ACCEPT DAMAGED SHIPMENTS UNLESS SUCH DAMAGE
IS NOTED ON THE DELIVERY RECEIPT AT THE TIME OF RECEIPT. Upon prompt
notification, Stryker Bertec will file a freight claim with the appropriate carrier for damages
incurred. Claims will be limited in amount to the actual replacement cost. In the event that this
information is not received by Stryker Bertec within the fifteen (15) days period following the
delivery of the merchandise, or the damage was not noted on the delivery notice at the time of
receipt, the customer will be responsible for payment of the original invoice in full.
Claims for any short shipment must be made within 5 days of invoice.
1.6 BED CLEANING AND MATTRESS CARE
Do not use harsh cleaners, solvents or detergents. Do not steam clean, hose off or
ultrasonically clean the bed. Do not immerse any part of the bed. The bed electrical parts may
be damaged by exposure to water.
Germicidal disinfectant, used as directed, and/or Chlorine Bleach products are not considered
mild detergents. These products are corrosive in nature and may cause damage to your bed if
used improperly. If these types of products are used, ensure the beds are rinsed with clean
water and thoroughly dried following cleaning. Failure to properly rinse and dry the beds will
leave a corrosive residue on the surface of the bed, possibly causing premature corrosion of
critical components. Failure to follow the above directions when using these types of cleaners
may void this product warranty.
Cleaning Beds
• Hand wash all surfaces of the bed with a soft cloth moistened with a solution of lukewarm
water and a mild detergent.
• Wipe the bed clean and dry thoroughly to avoid build up of cleaning solution.
C
C
A
A
U
U
T
T
I
I
O
O
N
N

Introduction Chapter 1
9
Mattress Care
Failure to properly clean mattress or dispose of them if defective will increase the risk of
exposure to pathogenic substances which may cause injury to the patient or user.
Inspection
• Implement local policies to address regular care, maintenance, and cleaning of
mattresses and covers. The cover cleaning and sterilization procedures can be found
below and on the bed label.
• Inspect mattress cover surface (also zip fasteners and cover inner surface if mattresses
have zip fasteners) regularly for signs of damage. If the mattress cover is stained, soiled,
or torn, examine the mattress, and seek instructions from the infection control nurses, as
the mattress may harbour micro-organisms. If the mattress is wet or badly stained,
withdraw the mattress from service.
• Seek the advice of infection control nurse in case of heavy soiling or infection, as general
cleaning procedures are unlikely to be adequate.
Cleaning and Sterilization
•Stains:
Wash with lukewarm water using a mild detergent. Rinse with water and let dry.
•Tough stains and sterilization:
Use bleach diluted with ten parts of water.
1.7 BED POSITION PICTOGRAMS
The following pictograms illustrate the GO BED basic positions.
Not illustrated here is the Cardiac Chair position which is obtained by combining the Reverse
Trendelenburg and the Auto Contour positions.
W
W
A
A
R
R
N
N
I
I
N
N
G
G
FOWLER ELEVATION VASCULAR
POSITION
KNEE GATCH ELEVATION
BED Hi-LoMOTION
TRENDELENBURG
POSITION
REVERSED TRENDELENBURG
POSITION
AUTO CONTOUR
POSITION
Figure 1.7

Chapter 1 The GO BED Operations Manual
10
1.8 BED ILLUSTRATION(Bed may differ from illustration)
HEAD IV POLE
HOLDERS
RESTRAINT STRAP
LOCATIONS
HEAD END
CASING SIDE MATTRESS
RETAINERS
RESTRAINT STRAP
LOCATIONS
EMERGENCY
CRANK STORED
FOLEY BAG HOOKS
FOOT END
CASING
EMERGENCY
CRANK OPENINGS
FOOT IV POLE
HOLDERS
SIDE MATTRESS
RETAINERS
FOOT MATTRESS
RETAINERS
PATIENT HELPER
MOUNTING SOCKETS
HEAD BOARD
SIDE-RAIL OUTSIDE
CONTROL PANEL
PUSH/PULL HANDLE
FOOT BOARD
BRAKE/STEER
PEDAL
FOOT BOARD
CONTROL PANEL
HEAD SIDE
-
RAIL
FOOT SIDE
-
RAIL
SIDE-RAIL INSIDE
CONTROL PANEL
ON/OFF SWITCH
HEAD SECTION
CENTER SECTION
THIGH SECTION
FOOT SECTION
SIDE-RAIL
LATCH LEVER
FIFTH WHEEL
Figure 1.8

Bed Operation Guide Chapter 2
11
2. BED OPERATION GUIDE
Features qualified as "Optional Equipment" are described throughout this chapter. They are
factory installed.
N
NO OT TE E
Throughout this guide, the words "right" and "left" refer to the right and left sides of a patient
lying face up on the bed.
2.1 SWITCHING ON POWER (ON/OFF SWITCH)
The main power switch, located beneath the foot board in the middle of the foot end case,
enables the bed functions to be activated or deactivated at any time. When the switch is turned
on, its green status indicator LED will light up indicating that the bed electric commands are
available. Note that side-rail controls are automatically shut off when the main power switch is
turned off.
2.2 APPLYING THE BRAKE
The GO BED is equipped with a central locking system activated by a brake/steer pedal
(see section 1.8, "Bed Illustration") located at the midpoint of the bed on both sides.
Always keep the caster brakes applied when a patient is on the bed (except during transport).
Serious injury could result if the bed moves while a patient is getting in or out of bed. After the
brake pedal is applied, push on the bed to ensure the wheels are locked.
Brake Pedal Operation
To engage the wheel brakes, press the red "TOTAL BRAKE" side of the brake/steer pedal
fully down on either side of the bed.
To disengage wheel brakes, press the brake/steer pedal opposite green "AXIAL STEER"
side until pedal reaches the neutral position (horizontal position).
2.3 MOVING THE BED
The GO BED is equipped with a 5th wheel steer mechanism (see section 1.8, "Bed Illustration")
activated by a brake/steer pedal located at midpoint of the bed on both sides.
The 5th wheel helps guiding the bed along a straight line and also for pivoting at corners.
When moving the bed with a patient in it, ensure that the bed is in the lowest position with side-
rails fully raised and securely locked in order to reduce risks of injuries to the patient.
Never move the bed using the raised side-rails nor hit the side-rails against any object found in
the room, for example: other furniture, walls, door frame, etc. Damage to the equipment could
result from such actions. Use the push/pull handles integrated on the head and foot boards to
move the bed, they provide a solid grip when moving the bed.
W
W
A
A
R
R
N
N
I
I
N
N
G
G
C
C
A
A
U
U
T
T
I
I
O
O
N
N
W
W
A
A
R
R
N
N
I
I
N
N
G
G

Chapter 2 The GO BED Operations Manual
12
Steer Pedal Operation
To engage the 5th wheel, press the green "AXIAL STEER" side of the brake/steer pedal fully
down on either side of the bed.
To disengage 5th wheel, press the red "TOTAL BRAKE" side of the brake/steer pedal until
pedal reaches the neutral position (horizontal position).
Moving the Bed in a Straight Line
Do not attempt to move the GO BED directly sideways with the 5th wheel activated. The 5th
wheel cannot pivot. Attempting to do so may cause injury to the patient or user.
1. Unplug power cord from wall outlet and roll it around the head end bumpers.
2. Lower the bed to its minimum height and raise side-rails. Ensure they are properly locked in
the up position.
3. Press the green "AXIAL STEER" side of the brake/steer pedal fully down to disengage
brakes and engage the 5th wheel.
4. Once the bed is moved, press the red "TOTAL BRAKE" side of the brake/pedal fully
down to engage the wheel brakes. Ensure the bed is immobilized by pushing on it.
5. Plug power cord back into wall outlet.
Moving the Bed in All Directions (Full Mobility)
1. Unplug power cord from wall outlet and roll it around the head end bumpers.
2. Lower the bed to its minimum height and raise side-rails. Ensure they are properly
locked in the up position.
3. Press the green "AXIAL STEER" side of the brake/steer pedal to disengage the wheel
brakes and stop when pedal reaches the neutral position (the 5th wheel must not be
engaged).
4. Once the bed is moved, press the red "TOTAL BRAKE" side of the brake/steer pedal
fully down and engage the brakes. Ensure the bed is immobilized by pushing on it.
5. Plug power cord back into wall outlet.
2.4 FOLEY BAG HOOK USAGE
Foley bag hooks (see section 1.8, "Bed Illustration") are found at three locations on both
sides of the bed, under the edges of the mattress support head, seat and foot sections.
The Foley bag hooks move when the Fowler is raised or lowered. Fowler motion must be
locked out when using these hooks to avoid inadvertent movement of the hooks.
W
W
A
A
R
R
N
N
I
I
N
N
G
G
C
C
A
A
U
U
T
T
I
I
O
O
N
N

Bed Operation Guide Chapter 2
13
2.5 FOOT PROP USAGE
A foot prop rod, integrated to the foot section is automatically
engaged when the Knee Gatch is raised. This foot prop
maintains the foot section nearly horizontal as the Knee Gatch
raises thus positioning the sleeping surface into the vascular
position (see section 1.7, "Bed Positions").
Since the foot prop rod automatically engages when the Knee Gatch is raised, it must be
disengaged manually whenever a simple Knee Gatch raise is required. To do so, perform
the following steps: •Reach under the foot section, lift the prop rod and hold it
while raising the Knee Gatch using the control located on
the foot board control panel.
•As the Knee Gatch raises, the rod will come to pass the
catches. Release it then and continue to raise the Knee
Gatch. The foot section will then simply follow the move of
the Knee Gatch without being propped.
2.6 FRACTURE FRAME USAGE
A standard fracture frame can be mounted on the bed using the IV sockets (see section 1.8,
"Bed Illustration") located on all four corners of the bed. The GO BED IV pole sockets
enable the use of IV poles in conjunction with a fracture frame.
2.7 PATIENT RESTRAINT STRAP LOCATIONS
The GO BED is equipped with 12 separate locations for installing patient restraint
straps. Ten of them are located on the mattress support edges directly across from
each other whereas the remaining two are located on the top part of the head
section, parallel to the head board (see section 1.8, "Bed Illustration").
2.8 CPR EMERGENCY RELEASE (OPTIONAL) USAGE
The instant CPR release is for emergency use only. When activating the instant CPR release,
all people and equipment must be removed from the area below and around the head and foot
sections of the bed or serious personal injury or damage to equipment could occur.
If the Fowler and the Knee Gatch are raised and quick access to the
patient is needed, pull outward one of the two emergency release
handles located under the Fowler both top corners and the Fowler and
Knee Gatch will lower to a flat position.
N
NO OT TE E
Once the instant CPR release is activated, the bed electrical functions
are not available for a few seconds, the time needed for the system to
reset itself.
W
W
A
A
R
R
N
N
I
I
N
N
G
G

Chapter 2 The GO BED Operations Manual
14
2.9 NIGHT LIGHT (OPTIONAL) USAGE
The GO BED may be equipped with an optional photoelectric night light to illuminate the
floor area around the bed. The night light turns on as the room lights dim. It is located on the
left side of the frame at the foot end of the bed.
2.10 NURSE CALL (OPTIONAL) USAGE
The bed may be equipped with an optional Nurse Call function allowing the patient to call for
nurse assistance by simply pressing the Nurse Call red button.
The Nurse Call module is integrated to both siderail panel controls, next to the control switches
(see section 2.14, page 17).
Included with this option are two Ø1/4" phono jacks located on both sides of the head end case.
The phono jacks enable the use of a nurse call cord which can be placed within reach of a
patient who is not in bed.
An optional cord with a Ø1/4" phono plug enables the linking of the bed to the hospital nurse call
system.
2.11 120V AUXILIARY POWER OUTLET USAGE (Available Only with 120V Bed)
The North American version (120V electrical system) of the GO BED may
be equipped with an optional CSA approved auxiliary power outlet with a 5A
breaker. Located on the left side at the foot end of the bed this feature
provides nursing staff with a convenient power source for peripheral
equipments.
2.12 POSITIONING SIDE-RAILS
To help reduce the number and severity of falls by patients, always leave the bed in the lowest
position and side-rails fully up when the patient is unattended. After raising a side-rail, pull firmly
on the side-rail to ensure it is securely locked into position.
Side-rails, with or without their padded covers or nets, are not intended to serve as restraint
devices to keep patient from exiting the bed. Side-rails are designed to keep a patient from
inadvertently rolling off the bed. It is the responsibility of the attending medical personnel to
determine the degree of restraint necessary to ensure a patient will remain safely in bed. Failure
to utilize the side-rails properly could result in serious patient injury.
To engage a head end side-rail, grasp the rail, pull it towards you and swing it upward towards
the head end of the bed until it latches in the up position.
To engage a foot end side-rail, the same procedure is required as for the head end side-rail,
however, the side-rail swings to the foot end of the bed.
To disengage a side-rail, lift it up slightly, push in the latch lever located under the sleeping
surface (see section 1.8, "Bed Illustration") and hold it as it rotates down to low position. Push
the side-rail against the sleeping surface to store it.
N
NO OT TE E
When both head and Gatch sections are raised, lower the head side-rail before lowering or
raising the foot side-rail, otherwise the raised head side-rail will impede the positioning of the
foot side-rail.
W
W
A
A
R
R
N
N
I
I
N
N
G
G

Bed Operation Guide Chapter 2
15
2.13 HEAD AND FOOT BOARDS
The GO BED has socket-type bed end mountings. The head board and the foot board slide
down into two mounting sockets located at each end of the bed. Both boards can be fixed
permanently. Two push/pull moulded handles are integrated on each board to provide a solid
grip when moving the bed.
Removing Boards
Seize both ends of the board and lift it up until posts come out of the mounting sockets.
Replacing Boards
Head board: Insert board with posts facing the outer side of the bed.
Foot board: Insert board with posts facing the inner side of the bed.
N
NO OT TE E
If the foot board is to be removed but the bed electric functions have to remain available.
Make sure that the side-rail controls are accessible by activating all three lock-out switches
before removing the foot board (green LED will go on indicating that the functions are
available to side-rail controls).
Fixing Boards Permanently
Boards can be fixed permanently to the mounting sockets by simply inserting 1/4-20 UNC x 2"
full-threaded mechanic screws (A) in factory installed nuts reachable through holes located on
the inner sides of the foot end and head end cases.
A
Figure 2.14

Chapter 2 The GO BED Operations Manual
16
2.14 SIDE-RAIL FUNCTION GUIDE
N
NO OT TE E
Side-rail control panel may differ in shape depending on the type of side-rail equipping the
bed.
OUTER CONTROL PANEL
Right side-rail Left side-rail
A: Push to raise Fowler. C: Push to raise sleeping surface E: Push to raise Knee Gatch
B: Push to lower Fowler. D: Push to lower sleeping surface F: Push to lower Kne Gatch
INNER CONTROL PANEL
Right Side-rail Left Side-rail
A: Push to raise Fowler. C: Push to raise Knee Gatch.
B: Push to lower Fowler. D: Push to lower Knee Gatch.
E: Push for nurse assistance (optional Nurse Call function, see section 2.10, page 14).
B
D
F
A
C
E
E
C
A
F
D
B
Figure 2.13A
E
C
A
A
C
D
B
B
D
E
Figure 2.13B

Bed Operation Guide Chapter 2
17
2.15 FOOT BOARD CONTROL PANEL GUIDE
Lock-out Switches (A1 to A3)
These three switches enable the selective lock out of the bed functions available to patient and
nursing staff through the side-rail control panels (inside and outside).
A1: : Push to give access to Fowler adjustment from both side-rail control panels. Lighted green
LED on pictogram indicates that Fowler adjustment is available through side-rail control
panels.
A2: Push to give access to Knee Gatch adjustment from both side-rail control panels. Lighted
green LED on pictogram indicates that Knee Gatch adjustment is available through side-rail
control panels.
A3: Push to give access to bed Hi-Lo control at both side-rail control panels. Lighted green LED
on pictogram indicates that Hi-Lo adjustment is available to nursing staff through the side-
rail outer control panel.
N
NO OT TE E
When a lock-out switch is used to inhibit a particular bed function of the side-rail control panels,
the function is inhibited on both sides of the side-rail control panel.
Lock-out settings are automatically saved in the event of a power failure and restored following
resumption of power.
Fowler Control Switches (B1 and B2)
These two switches enable the adjustment of the Fowler.
B1: Push to raise Fowler.
B2: Push to lower Fowler.
Knee Gatch Control Switches (C1 and C2)
These two switches enable the adjustment of the Knee Gatch.
C1: Push to raise Knee Gatch.
C2: Push to lower Knee Gatch.
S
LEEPING SURFACE POSITION SWITCH
HEAD THIGH BED
TRENDELENBURG
SWITCH
WHEN ON
CONTOUR
SIDE
-
RAIL BED
FUNCTION
LOCK
-
OUT SWITCH
AUTOMATIC CONTOUR
INDICATOR PICTOGRAM
(
OPTIONAL
)
A1 B1 C1 D1
F
E
A2 A3 B2 C2 D2

Chapter 2 The GO BED Operations Manual
18
Hi-Lo Switches (D1 and D2)
These two switches enable adjustment of the sleeping surface height (Hi-Lo).
D1: Push to raise the sleeping surface
D2: Push to lower the sleeping surface.
Trendelenburg Switch (E)
This switch, when activated, enables both Trendelenburg positions through the Hi-Lo switches.
Alighted green LED on the pictogram indicates that Trendelenburg positioning is available.
E: Push to activate the Trendelenburg positions which then becomes available through the Hi-
Lo switches.
Trendelenburg: Push switch D1 to lower head end/raise foot end of the bed.
Reverse Trendelenburg: Push switch D2 to lower foot end/raise head end of the bed.
N
NO OT TE E
To replace sleeping surface to horizontal position after Trendelenburg positioning, simply press
the Trendelenburg switch to deactivate the function (green LED will go out) and lower or raise
the sleeping surface to its limit. Then position the bed to the desired height.
Auto Contour (optional) Pictogram (F)
This figure, illustrating the Contour position, points to the lock-out switch to activate in the foot
board control panel to position the bed automatically to the Contour position.
Contour positioning automatically raises the Knee Gatch as the Fowler is raised. This position
prevents the patient from slipping towards the foot of the bed.
F: As indicated by the pictogram arrow, push the Knee Gatch lock-out switch (A2)to enable the
Auto Contour positioning.
N
NO OT TE E
To obtain the Auto Contour position when raising the Fowler from a side-rail control panel, not
only the Knee Gatch function, but also the Fowler function, must be made available to side-rail
control panels through activating their respective lock-out switches (A1 and A2)in the foot
board control panel.

Accessories Chapter 3
19
3. ACCESSORIES
N
NO OT TE E
Features qualified as "Accessory" are described in this section of the guide. They are products,
as is the GO BED, and can be ordered at the same time beds are ordered or later on. They
carry a product number (P/N).
3.1 IV POLE
Eight electrically insulated IV pole sockets are available on the GO BED to receive three
models of IV poles offered as accessories. Both ends of the bed possess two IV pole
holders, each capable of receiving a 3/4"Ø pole with 1/2"Ø anchor pin and a 1"Ø heavy duty
pole with 5/8"Ø anchor pin.
Removable Anodized Aluminum IV Pole
3/4"Ø pole with 1/2"Ø anchor pin for hanging IV bags or other accessories. Maximum
weight capacity: 40 lb/18kg.
Fits into one of the four 3/4"Ø -1/2"Ø sockets.
Removable Anodized Aluminum IV Pole
1"Ø heavy duty pole with 5/8"Ø anchor pin for hanging IV bags or other accessories.
Maximum weight capacity: 40 lb/18kg.
This pole fits into one the four 1"Ø -5/8"Ø sockets and is equipped with a spring pin that
prevents rotation of the pole once it is inserted into the socket.
Permanently Attached Anodized Aluminum IV Pole
1"Ø heavy duty pole with 5/8"Ø anchor pin for hanging IV bags or other accessories. Can
be folded onto the bed. Maximum weight capacity: 40 lb/18kg.
Fits into one of the two 1"Ø -5/8"Ø sockets located at the head of the bed and is equipped
with a spring pin that prevents rotation of the pole once it is inserted into the socket.
Installing the Permanently Attached IV Pole
1. Insert pole in one the two 1"Ø -5/8"Ø sockets
located at the head of the bed.
2. Fasten a 5/16-18UNC x 3 ½" bolt (A) into the IV
pole hole located at the lower extremity of the
pole.
N
NO OT TE E
After inserting pole into socket, ensure that spring pin is
engaged in slot by rotating pole until engaged pin
prevents further movement.
A

Chapter 3 The GO BED Operations Manual
20
3.2 PENDANT CONTROL USAGE
Different models of pendant controls offering access to two or three bed functions are available
as accessories with the GO BED. A clip for bed sheet is integrated on all models allowing the
pendant control to be placed within patient reach. Some models come with a hook for
installation on side-rail.
Installing a Pendant Control
1. Loosen the lock ring holding the side-rail bed function cable to the bed frame receptacle
under the seat section and remove the cable plug.
2. Connect the pendant control plug (A) to the bed receptacle and tighten the lock ring (B).
3. Test pendant control functions for proper operation.
N
NO OT TE E
The installation of a pendant control requires that the side-rail control cable be disconnected
from the bed thus rendering inoperative the side-rail control functions.
BA
CLIP FOR
BED SHEET
TWO FUNCTION PENDANT
CONTROL WITH HOOK
HOOK