Stryker THC5 User manual

www.stryker.com 0000-001-023 REV C 1
THC5 (11225) Assembly instructions
Items needed
• (1) THC5, stan assembly (p/n 11225)
• (1) Instruction sheet (p/n 0000-001-023)
Tools required
• 7/16” Wrench
• Torque wrench
Procedure
To assemble the THC5 pole
1. Insert the pin locate on the en of the pole, into the gui e pin hole on the base (Figure 1 on page 1 an Figure 2 on
page 1).
Figure 1 Pin Figure 2 Base
2. Tip the stan over an insert the provi e screw an washer into the bottom of the base (Figure 3 on page 1).
Figure 3 Bottom of the base Figure 4 THC5 assembly
3. Using a 7/16" wrench an torque wrench (20.5 ± 3 ft-lb), tighten the screw an washer.
4. Turn the stan over an make sure the pole is secure to the stan (Figure 4 on page 1).

2 0000-001-023 REV C www.stryker.com
THC5 (11225) Assembly instructions
Procedure (Continued)
CAUTION
Always mount the warming unit securely before use to avoi the risk of injury or equipment amage.
To install Mistral-Air onto the THC5 stand
1. Lift the Mistral-Air unit from the top using the han le (Figure 5 on page 2).
Figure 5 Top handle Figure 6 Stand protrusion
2. Orient the Mistral-Air control panel opposite of the protrusion on the stan (Figure 6 on page 2).
3. Sli e the Mistral-Air unit onto the THC5 stan by placing the curve in entation on the back of the unit over the top
of the stan with the power cor on the outsi e of the stan protrusion (Figure 7 on page 2).
Figure 7 Mistral-Air onto the THC5 stand Figure 8 Secure
4. Stop sli ing the Mistral-Air unit when the curvature touches the protrusion on the stan .
5. Turn the knob clockwise to lock the Mistral-Air unit onto the THC5 stan .
6. Make sure that the Mistral-Air unit is secure an oes not tip (Figure 8 on page 2).
Note See the Mistral-Air warming unit operations manual for safety an usage.
To remove Mistral-Air from the THC5 stand
1. Turn the knob counter clockwise to unlock the Mistral-Air unit from the THC5 stan while hol ing onto the Mistral-Air
han le.
2. Lift the Mistral-Air unit upwar to remove from the stan .

www.stryker.com 0000-001-023 REV C 3
THC5 (11225) Assembly instructions
Caster replacement
Kit contents for caster without brakes (0000-001-545) Kit contents for caster with brakes(0000-001-547)
• (1) Caster, without brake (0000-001-544)
• (1) Fastener, washer (0000-001-548)
• (1) Fastener, nut (0000-001-549)
• (1) Instruction sheet (0000-001-023)
• (1) Caster, with brake (0000-001-546)
• (1) Fastener, washer (0000-001-548)
• (1) Fastener, nut (0000-001-549)
• (1) Instruction sheet (0000-001-023)
Tools required
• 7/16” Wrench
• Torque wrench
To replace a caster, follow these procedures
1. Using a 7/16” wrench, unscrew the bolt an lock washer that secure the caster to the base.
4
3
Torque item 3 and 4
to 20.5 ± 3 ft-lb
Figure 9 Caster replacement
2. Remove an iscar the caster, washer, an nut.
3. Reverse to reinstall.
Notes
• Do not put a caster with a brake next to one another.
• Use the torque wrench for reinstall.
4. Verify proper operation of the pro uct before returning it to service.
3800 E. Centre Avenue, Portage, MI 49002 USA
1-800-327-0770 | 2016/03 C.1