studioduc indi full User manual

indi doublewide desk
a how-to guide that won’t leave you in tears
ASSEMBLY INSTRUCTIONS

parenting is hard.
this is easy.
no really, it is.
MADE HERE™
MADE SAFE MADE SMART
MADE WELL™

want to watch this assembly IRL?
(acronym challenged? that means “in real life”.)
open the camera on your phone and place it over the
QR code below to see our NYC studio dream team do all
the heavy lifting (just kidding, there is none!)
or go to ducducnyc.com/pages/assembly-instructions

thank you for selecting a
studio duc product!

please check contents against the components list in these
instructions. also, please ensure there was no damage that may
have occurred in shipping.
if any components are missing or you find any damage, please
contact ducduc before continuing.
read all the instructions before use.
pay close attention to the safety warnings in these instructions.
a minimum of two people is required to safely assemble and
move the desk. do not attempt to move this desk alone —
dragging or sliding it across a floor may cause structural
damage.
CLEANING:
do not scratch or chip the finish. do not use abrasive chemicals
for cleaning. clean with mild soap on a soft rag. rinse and dry
thoroughly. if you ever refinish this furniture, be sure to use only
a non-toxic finish specified for children’s furniture.
KEEP INSTRUCTIONS FOR FUTURE USE

D (x2)
adjustable shelf
RC1
R case exterior side
RC4
R case door
RC2
R case interior side
RC3
R case fixed shelf
LC1
L case exterior side
LC4
L case door
LC2
L case interior side
LC3
L case fixed shelf
WHAT’S IN THE BOX:
A
desktop back
B
desktop
C (x2)
bottom
E (x2)
back panel
I
hammer cap
K (x2)
indi pull
L (x4)
screw for indi pull
F (x8)
foot
M (x8)
shelf pin
J (x6)
screw for bracket
G (x8)
JCB bolt (25mm)
H
allen key (4mm)

WHAT YOU’LL NEED:
20 minutes
(or less)
2 people
plus a dog for moral support
(unless you’re a cat person)
household hammer or
rubber mallet
a soft surface to assemble on
(like a rug or some of the corrugate
box your piece arrived in)
phillips head screwdriver and/or
drill with 6mm bit

lean one bottom (C) against a wall as shown.
using the provided allen key (H) and JCB bolts (G x4), attach feet (F x4) to bottom (C). once
all feet are securely attached, set the assembled base aside.
2
1
important!
be sure the JBC bolts are
attached to the side of the
bottom panel WITH the
countersink holes. duc insider tip!
be sure the edges of the
feet are square to the
edges of the bottom
panel before fully
tightening the JCB bolts.
still confused? scan this code to watch the assembly video!

lean R case exterior side (RC1) against a wall as shown.
insert connectors on one back panel (E) into the 3 bottom slots on R case exterior side (RC1)
as shown. push down at the connection to lock into place.
4
3
important!
the top slot on
the side panel will
be left empty
still confused? scan this code to watch the assembly video!

insert connectors on back panel (E) into slots on R case interior side (RC2). push down at
the connection to lock into place.
5
6a have a friend gently flare R case exterior + interior sides (RC1 + RC2) outward as shown.
still confused? scan this code to watch the assembly video!

6c
6b with the sides flared outward, insert the connectors of one side of bottom (C) and R case
fixed shelf (RC3) into slots on R case interior side (RC2).
insert remaining connectors of bottom (C) and R case fixed shelf (RC3) into slots on R
case exterior side (RC1).
important!
when inserting
the fixed shelf, be
sure the magnetic
catch hardware
is diagonal to the
hinge hardware on
the case interior
still confused? scan this code to watch the assembly video!

6d once all connectors and slots are lined up and case sides are back to square position,
apply hammer cap (I) to the head of a household hammer and tap bottom (C) and fixed
shelf (RC3) until there is no gap at the connection to back panel (E).
repeat steps 1-6 to create the second case from the remaining parts.
7
still confused? scan this code to watch the assembly video!

lean desktop (B) against the wall with the slots facing out.
insert connectors on desktop back (A) into slots on desktop (B). use hammer with hammer
cap (I) to lock into place.
8
9
duc insider tip!
if you’re having trouble
locking in A to B all the
way, tilt the partially
assembled piece as
shown so the connector
on the desktop back is
not touching the ground.
still confused? scan this code to watch the assembly video!

11 place both cases in the location where the desk will be fully assembled with the cases
spaced 60” apart.
still confused? scan this code to watch the assembly video!
12 with a friend, lift assembled desktop (A + B) and first line up connectors on the desktop back
(A) with the slots on both case side exteriors (RC1 + LC1). next, line up connectors on both
case interior sides (RC2 +LC2 ) with the holes on the underside of desktop (B). use hammer
with hammer cap (I) to lock into place.

13 use screws (J) and your phillips head screwdriver to secure desktop (B) to both case exterior
sides (RC1 + LC1) using the attached brackets and pre-drilled holes.
duc insider tip!
if you’re handy and
want to save a few
secs, feel free to use a
household drill.
14a use your phillips screwdriver and screws (L), attach indi pull hardware (K) to the front
of both doors (RC4 + LC4).
still confused? scan this code to watch the assembly video!

14b attach L door (LC4) to L case exterior side (LC1) by lining up the hardware and firmly
pushing on it until it clicks into place.
important!
be sure the hardware is
in extended position as
shown. you will hear an
audible click when the
connection is made.
15 attach R door (RC4) to R case exterior side (RC1) using the same method.
still confused? scan this code to watch the assembly video!

16a
16b
insert 4 shelf pins (M) into holes on both R case sides (RC1 + RC2) at desired height.
place adjustable shelf (D) on top of 4 shelf pins (M) so it sits secure and level.
still confused? scan this code to watch the assembly video!

17 use steps 16a + 16b to install the remaining adjustable shelf (D) on the L case.
still confused? scan this code to watch the assembly video!

bravo! you did it!
give yourself a pat on the back, take a bow,
or go house a pint of ice cream…we don’t judge.

prefer to talk to a human instead?
we’re here for you!
contact our customer advocate team below:
212.226.1868
live chat at
ducducnyc.com
200 lexington, no. 701
ny, ny 10016
[e-mail]