studioduc indi full User manual

indi dresser/changer
a how-to guide that won’t leave you in tears
ASSEMBLY INSTRUCTIONS

parenting is hard.
this is easy.
no really, it is.
MADE HERE™
MADE SAFE MADE SMART
MADE WELL™

want to watch this assembly IRL?
(acronym challenged? that means “in real life”.)
open the camera on your phone and place it over the
QR code below to see our NYC studio dream team do all
the heavy lifting (just kidding, there is none!)
or go to ducducnyc.com/pages/assembly-instructions

thank you for selecting a
studio duc product!

Please check contents against the components list in these instructions. Also, please ensure
there was no damage that may have occurred in shipping. If any components are missing or
you find any damage, please contact ducduc before continuing.
We recommend the use of a Colgate 3-Sided contour Pad (CR300-S80) if this dresser is to be
used as a changing table.
Maximum changing pad dimensions: W16” x L33” x H5”.
Pay close attention to the safety warnings in these instructions and on dresser/changer labels.
The maximum weight of any child on top of the dresser/changer is 45 pounds.
Read all the instructions before use.
Do not use if dresser/changer is damaged or broken.
CARE AND CLEANING:
Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning. Clean with mild
soap on a soft rag. Rinse and dry thoroughly. If you ever re-finish this furniture, be sure to use
only a non-toxic finish.
Do not attempt to move this dresser/changer alone–dragging or sliding it across a floor may
cause structural damage. A minimum of two people is required to safely lift and reposition the
dresser/changer.
KEEP INSTRUCTIONS FOR FUTURE USE
Please check contents against the components list in these
instructions. Also, please ensure there was no damage that may have occurred in
shipping. If any components are missing or you find any damage, please contact
ducduc before continuing.
To use the dresser as a changing table, insert and use the changing table tray
provided with the dresser.
We recommend the use of a Colgate 3-Sided contour Pad (CR300-S80) if this
dresser is to be used as a changing table.
Maximum changing pad dimensions: W16” x L33” x H8”.
Pay close attention to the safety warnings in these instructions and on dresser/
changer labels.
The maximum weight of any child on top of the dresser/changer is 45 pounds.
Read all the instructions before use.
Do not use if dresser/changer is damaged or broken.
CARE AND CLEANING:
Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning.
Clean with mild soap on a soft rag. Rinse and dry thoroughly. If you ever
re-finish this furniture, be sure to use only a non-toxic finish.
Do not attempt to move this dresser/changer alone- dragging or sliding it across
a floor may cause structural damage. A minimum of two people is
required to safely lift and reposition the dresser/changer.
KEEP INSTRUCTIONS FOR FUTURE USE
secure this unit to support surface using the
mounting hardware provided. see instructions.

WHAT’S IN THE BOX:
A1
R side panel
DB2 (x3)
drawer box back
DB3 (x3)
L drawer box side
DB4 (x3)
R drawer box side
DB5 (x3)
drawer box bottom
DB6 (x3)
indi pull
DB7 (x6)
screw for indi pull
K (x2)
confirmat screw for
stretcher
F (x4)
foot
J
safety strap kit
(with hardware)
B
back panel
C
bottom
D
tray stretcher
A2
L side panel H (x4)
JCB bolt (25mm)
L
allen key (3mm)
DB1 (x3)
drawer face
E
top G
hammer cap
I
allen key (4mm)

WHAT YOU’LL NEED:
20 minutes
(or less)
2 people
plus a dog for moral support
(unless you’re a cat person)
household hammer or
rubber mallet
a soft surface to assemble on
(like a rug or some of the corrugate
box your piece arrived in)
phillips head screwdriver

lean bottom (C) against a wall as shown.
using the provided allen key (I) and JCB bolts (H), attach feet (F) to bottom (C). once all
feet are securely attached, set the assembled base aside.
2
1
important!
be sure the JBC bolts are
attached to the side of the
bottom panel WITH the
countersink holes. duc insider tip!
be sure the edges of the
feet are square to the
edges of the bottom
panel before fully
tightening the JCB bolts.
still confused? scan this code to watch the assembly video!

lean L side panel (A2) against a wall as shown.
3
4insert connectors on back panel (B) into slots on L side panel (A2). push down at the
connection to lock into place.
important!
be sure the 3
holes on the back
panel are located
at the top interior
still confused? scan this code to watch the assembly video!

insert connectors on back panel (B) into slots on R side panel (A1). push down at the
connection to lock into place.
gently lay the partially assembled case on its back and have a friend gently flare the side
panels (A1 + A2) outward as shown.
6a
5
still confused? scan this code to watch the assembly video!

6b with the side panels flared outward, insert connectors of assembled base (C + F) and top
(E) into slots on R side panel (A1).
still confused? scan this code to watch the assembly video!

6d once all connectors and slots are lined up and side panels are back to square position,
apply hammer cap (G) to the head of a household hammer and tap bottom panel (C) and
top (E) until there is no gap at the connection to back panel (B).
6c insert remaining connectors on assembled base (C + F) and top (E) into slots on L side
panel (A2).
still confused? scan this code to watch the assembly video!

with a friend, rotate the assembled case into upright position. position tray stretcher (D)
between two side panels (A1 + A2) as shown. once the connectors on tray stretcher (D)
are lined up with the holes on top (E), use hammer with hammer cap (G) to tap until
secure.
insert screws (K) into holes on side panels (A1 + A2). use allen key (L) to secure tray
stretcher (D) to side panels (A1 + A2).
7a
7b
duc insider tip!
when attaching the tray
stretcher, start by loosely
screwing in each bolt.
once everything is lined up and
both bolts are in place, fully
tighten all screws until secure.
still confused? scan this code to watch the assembly video!

8b rotate the partially assembled drawer box as shown. slide drawer box bottom (DB5) into
place using grooves on the drawer box side panels (DB3 + DB4) as guides. be sure glide
hardware on bottom panel (DB5) is positioned outside the drawer interior and toward
the drawer face (DB1) as shown.
8a now we build the drawers! starting with drawer face (DB1) facing down, insert
connectors of both drawer box side panels (DB3 + DB4) into slots on drawer face (DB1).
push down at the connections to lock into place.
still confused? scan this code to watch the assembly video!

8d using a phillips screwdriver and screws (DB7), attach the pull hardware (DB6) to the front
of each drawer face.
8c again, rotate partially assembled drawer box as shown. insert connectors of drawer box
back (DB2) into slots on drawer box sides (DB3 + DB4). push down at the connections to
lock into place. use hammer and hammer cap (F) if needed.
still confused? scan this code to watch the assembly video!

starting at the top, pull drawer glides out to extended position as shown.
10a
9build remaining drawers using steps 8a, 8b, 8c, and 8d.
still confused? scan this code to watch the assembly video!

10b place one assembled drawer box onto extended glides as shown. from underside of
drawer, use hands to pull each glide forward until it locks into connection with glide
hardware attached to drawer box bottom (DB5). the drawer will be secure when you
hear a click on each connection. once secured, push drawer box in to close.
still confused? scan this code to watch the assembly video!

11
12
repeat steps 10a + 10b to install the remaining drawers.
safety strap installation
Important! Do not skip this step. Furniture tipping over is a serious threat to children’s
safety.
the last step for your dresser/changer is to install the safety strap included in the box. ref-
erence the separate instructions enclosed in the envelope.

yippee! you did it!
give yourself a pat on the back, take a bow,
or go house a pint of ice cream…we don’t judge.

prefer to talk to a human instead?
we’re here for you!
contact our customer advocate team below:
212.226.1868
live chat at
ducducnyc.com
200 lexington, no. 1201
ny, ny 10016
[e-mail]