studioduc juno tall bookcase User manual

juno tall bookcase
a how-to guide that won’t leave you in tears
ASSEMBLY INSTRUCTIONS

parenting is hard.
this is easy.
no really, it is.
MADE HERE™
MADE SAFE MADE SMART
MADE WELL™

want to watch this assembly IRL?
(acronym challenged? that means “in real life”.)
open the camera on your phone and place it over the
QR code below to see our NYC studio dream team do all
the heavy lifting (just kidding, there is none!)
or go to ducducnyc.com/pages/assembly-instructions

thank you for selecting a
studio duc product!

please check contents against the components list in these
instructions. also, please ensure there was no damage that may
have occurred in shipping.
if any components are missing or you find any damage, please
contact ducduc before continuing.
read all the instructions before use.
pay close attention to the safety warnings in these instructions.
a minimum of two people is required to safely assemble and
move the tall bookcase. do not attempt to move this tall
bookcase alone — dragging or sliding it across a floor may
cause structural damage.
MAINTENANCE:
please remember to securely tighten all bolts and fasteners, and
periodically check to make sure every component is properly
and securely in place and all bolts and fasteners are tight.
CLEANING:
do not scratch or chip the finish. do not use abrasive chemicals
for cleaning. clean with mild soap on a soft rag. rinse and dry
thoroughly. if you ever refinish this furniture, be sure to use only
a non-toxic finish specified for children’s furniture.
KEEP INSTRUCTIONS FOR FUTURE USE

WHAT’S IN THE BOX:
A1
R side panel
A2
L side panel I
hammer cap
H (x16)
shelf pins
C
stretcher
D
top
F (x4)
adjustable shelves
E
bottom
B1
back panel top
B2
back panel bottom
G
safety strap kit
(with hardware)
J (x28)
dowel pins

a soft surface to assemble on
(like a rug or some of the corrugate
box your piece arrived in)
WHAT YOU’LL NEED:
10 minutes
(or less)
2 people
plus a dog for moral support
(unless you’re a cat person)
household hammer or
rubber mallet
phillips head screwdriver
and/or drill with 6mm bit

before you begin!
then, follow the instructions below. once completed
and all dowel pins are secured, move on to step 1!
grab your household hammer and locate the parts
listed below.
• line up the skinny end of the green dowel
pins (J) with holes on the top and sides of
R side panel, L side panel (parts: A1 + A2)
• apply hammer cap (I) to the head of a
household hammer and hit the top of the
dowel until it is fully secure.
• repeat on all case edges until no empty
holes remain.
I
hammer cap
J (x28)
dowel pins
A1
R side panel
A2
L side panel

lean R side panel (A1) against a wall with the holes facing away from wall and connectors
facing upward as shown.
insert connectors of bottom panel (E) into slots on R side panel (A1) and push down at the
connection to lock into place.
2
1
still confused? scan this code to watch the assembly video!

insert remaining connectors of bottom panel (E) into slots on L side panel (A2), and push
down at the connection to lock into place.
insert connectors of both side panels (A1 + A2) into holes on underside of top panel
(D). apply hammer cap (K) to the head of a household hammer and tap top panel (D)
until there is no gap at the connection to side panels (A1 + A2).
4
3
still confused? scan this code to watch the assembly video!

with a friend, rotate the partially assembled case as shown. insert connectors of both side
panels (A1 + A2) into holes on back panel top (B1). tap with hammer and
hammer cap (I) until fully in place.
insert connectors of both side panels (A1 + A2) into holes on back panel bottom (B2).
tap with hammer and hammer cap (I) until fully in place.
6
5
duc insider tip!
not sure which back panel is top or
bottom? look for the feet... those go
down low (AKA: the bottom).
still confused? scan this code to watch the assembly video!

7insert connectors of stretcher (C) into slots on both side panels (A1 + A2). tap stretcher (C)
with hammer and hammer cap (I) until fully in place.
with a friend, rotate the assembled case into upright position, as shown.
8
still confused? scan this code to watch the assembly video!

insert 16 shelf pins (H) into holes on interiors of both side panels (A1 + A2) at desired
locations. place 1 adjustable shelf (F) on top of 4 shelf pins (H) so each shelf sits secure
and level.
9
still confused? scan this code to watch the assembly video!

10
the last step for your tall bookcase is to install the
safety strap included in the box. reference the separate
instructions enclosed in the envelope.
safety strap installation
still confused? scan this code to watch the assembly video!

congrats! you did it!
give yourself a pat on the back, take a bow,
or go house a pint of ice cream…we don’t judge.

prefer to talk to a human instead?
we’re here for you!
contact our customer advocate team below
212.226.1868
live chat at
ducducnyc.com
200 lexington ave,
ny, ny 10016
[e-mail]