studioduc juno User manual

juno stacking toy cubby
a how-to guide that won’t leave you in tears
ASSEMBLY INSTRUCTIONS

parenting is hard.
this is easy.
no really, it is.
MADE HERE™
MADE SAFE MADE SMART
MADE WELL™

want to watch this assembly IRL?
(acronym challenged? that means “in real life”.)
open the camera on your phone and place it over the
QR code below to see our NYC studio dream team do all
the heavy lifting (just kidding, there is none!)
or go to ducducnyc.com/assembly-instructions

thank you for selecting a
studio duc product!

please check contents against the components list in these
instructions. also, please ensure there was no damage that may
have occurred in shipping.
if any components are missing or you find any damage, please
contact ducduc before continuing.
read all the instructions before use.
pay close attention to the safety warnings in these instructions.
a minimum of two people is required to safely assemble and
move the stacking toy cubby. do not attempt to move the
stacking toy cubby alone — dragging or sliding it across a floor
may cause structural damage.
MAINTENANCE:
please remember to securely tighten all bolts and fasteners, and
periodically check to make sure every component is properly
and securely in place and all bolts and fasteners are tight.
CLEANING:
do not scratch or chip the finish. do not use abrasive chemicals
for cleaning. clean with mild soap on a soft rag. rinse and dry
thoroughly. if you ever refinish this furniture, be sure to use only
a non-toxic finish specified for children’s furniture.
KEEP INSTRUCTIONS FOR FUTURE USE

WHAT’S IN THE BOX:
B
back panel
C
bottom
E
hammer cap
D
top
A1
L side panel
A2
R side panel
F
safety strap kit
(with hardware)

a soft surface to assemble on
(like a rug or some of the corrugate
box your piece arrived in)
WHAT YOU’LL NEED:
15 minutes
(or less)
2 people
plus a dog for moral support
(unless you’re a cat person)
phillips head screwdriver
and/or drill with 6mm bit
household hammer or
rubber mallet

lean R side panel (A2) against a wall as shown.
insert connectors of back panel (B) into slots on R side panel (A2). push down at the
connection to lock into place.
2
1

insert connectors of back panel (B) into slots on L side panel (A1). push down at the
connection to lock into place.
have a friend gently flare L + R side panels (A1 + A2) outward as shown.
4a
3
still confused? scan this code to watch the assembly video!

with the side panels flared outward, insert connectors of bottom (C) into slots on R side
panel (A2).
insert remaining connectors of bottom (C) into slots on L side panel (A1).
4b
4c
still confused? scan this code to watch the assembly video!

once all connectors and slots are lined up and side panels are back to square position,
apply hammer cap (E) to the head of a household hammer and tap bottom (C) until it is
flush with the backside of back panel (B).
4d
with a friend, flip partially assembled case into upright position. line up holes of top (D) and
insert with the connectors of side panels (A1 + A2) and back panel (B). tap with hammer and
hammer cap (E) to lock into place.
5
still confused? scan this code to watch the assembly video!

the following instructions describe how to stack your
toy cubby units and apply the safety strap if
stacking two or more. if you will not be stacking your toy
cubby units, you can stop here.
before you move forward!
6a place your stacking toy cubby unit in the area it will stay. do not try to move the unit
once it has been stacked.
still confused? scan this code to watch the assembly video!

6b have a friend help you lift the second stacking toy storage on top of the first. make sure
the notches in the legs are aligned with the grooves in the top of the unit below.
duc insider tip!
this modular toy storage has been
designed to stack securely for the
perfect fit. If for any reason, you
do not feel the pieces are locking
into place, please contact ducduc
before proceeding.
still confused? scan this code to watch the assembly video!
6c place your stacking toy storage unit in the area it will stay. do not try to move the unit
once it has been stacked.

7
the last step for your stacking toy cubby is to install the
safety strap included in the box. reference the separate
instructions enclosed in the envelope.
safety strap installation

woohoo! you did it!
give yourself a pat on the back, take a bow,
or go house a pint of ice cream…we don’t judge.

prefer to talk to a human instead?
we’re here for you!
contact our customer advocate team below:
212.226.1868
live chat at
ducducnyc.com
200 lexington, no. 701
ny, ny 10016
[e-mail]