studioduc knox stacking User manual

knox stacking
toy storage
a how-to guide that won’t leave you in tears
ASSEMBLY INSTRUCTIONS

parenting is hard.
this is easy.
no really, it is.
MADE HERE™
MADE SAFE MADE SMART
MADE WELL™

want to watch this assembly IRL?
(acronym challenged? that means “in real life”.)
open the camera on your phone and place it over the
QR code below to see our NYC studio dream team do all
the heavy lifting (just kidding, there is none!)
or go to ducducnyc.com/pages/assembly-instructions
if you’re already using your phone, just click the
orange button below!
ASSEMBLY VIDEO CHANNEL

thank you for selecting a
studio duc product!

please check contents against the components list in these
instructions. also, please ensure there was no damage that may
have occurred in shipping.
if any components are missing or you find any damage, please
contact ducduc before continuing.
read all the instructions before use.
pay close attention to the safety warnings in these instructions.
a minimum of two people are required to safely assemble and
move the product. do not attempt to move this product alone —
dragging or sliding it across a floor may cause structural
damage.
MAINTENANCE:
please remember to securely tighten all bolts and fasteners, and
periodically check to make sure every component is properly
and securely in place and all bolts and fasteners are tight.
CLEANING:
do not scratch or chip the finish. do not use abrasive chemicals
for cleaning. clean with mild soap on a soft rag. rinse and dry
thoroughly. if you ever refinish this furniture, be sure to use only
a non-toxic finish specified for children’s furniture.
KEEP INSTRUCTIONS FOR FUTURE USE

WHAT’S IN THE BOX:
A2
L side panel
E (x2)
center partition
F (x2)
door
B
back panel
C
bottom
A1
R side panel
D
top
G (x4)
foot

J
hammer cap
H (x2)
knox pull hardware
O
safety strap kit
(with hardware)
K (x2)
tray bracket
L (x8)
JCB bolt
(20mm)
M (x8)
washer
N
allen key
(4mm)
I (x2)
screw for knox pull
WHAT’S IN THE BOX:

WHAT YOU’LL NEED:
20 minutes
(or less)
2 people
plus a dog for moral support
(unless you’re a cat person)
household hammer or
rubber mallet
a soft surface to assemble on
(like a rug or some of the corrugate
box your piece arrived in)
phillips head screwdriver
and/or drill with 6mm bit

lean bottom (C) against a wall as shown.
beginning in one corner, take one foot (G) as seen below, and insert the bolt located on foot
(G) into the brackets on bottom panel (C). Twist until the foot is fully secure, and repeat for
all feet (G) provided. Place bottom panel with attached feet aside for now.
2
1
still confused? click to watch the assembly video ASSEMBLY VIDEO CHANNEL

lean R side panel (A1) against a wall as shown.
3
4insert connectors on back panel (B) into slots on R side panel (A1). push down at the
connection to lock into place. if needed, use hammer with hammer cap (J) to tap until
secure.
still confused? click to watch the assembly video ASSEMBLY VIDEO CHANNEL
important!
be sure that the holes located on back
panel (B) are facing OUT, as seen in the
images above.
B
back panel

5insert connectors on back panel (B) into slots on remaining L side panel (A2). push down
or tap with hammer + hammer cap (J) at the connection to lock into place.
still confused? click to watch the assembly video ASSEMBLY VIDEO CHANNEL

6gently lay the partially assembled case on its back.
locate bottom panel (C) with attached feet (H)
before moving on to the next step.
wait!
still confused? click to watch the assembly video ASSEMBLY VIDEO CHANNEL

insert connectors on both side panels (A1 + A2) into slots on bottom panel (C). push down or
tap with hammer and hammer cap (J) to lock into place.
7
still confused? click to watch the assembly video ASSEMBLY VIDEO CHANNEL

lower both center partitions (E) into the partially assembled case. insert connectors on center
partitions (E) into the remaining slots on bottom panel (C). push down or tap with hammer and
hammer cap (J) to lock into place.
8
still confused? click to watch the assembly video ASSEMBLY VIDEO CHANNEL

flip partially assembled case into upright position. line up holes of top (D) with the
connectors of side panels (A1 + A2), center partitions (E) and back panel (B). tap with hammer
and hammer cap (J) to lock into place.
9
still confused? click to watch the assembly video ASSEMBLY VIDEO CHANNEL

10
11
using a phillips screwdriver and screw (I), attach the pull hardware (H) to the door
panel (F).
repeat step 12 for remaining door (F).
still confused? click to watch the assembly video ASSEMBLY VIDEO CHANNEL

12 slightly angle one door panel (F) into the case as shown below. Insert the door upward into
the track closest to the back of the case. then, allow the door to drop down into the same
track on the bottom panel (C). to confirm that it is installed correctly, just try sliding the
door side to side.
still confused? click to watch the assembly video ASSEMBLY VIDEO CHANNEL
important!
the hardware pull should be on the right
side for this step.
D
top

13
still confused? click to watch the assembly video ASSEMBLY VIDEO CHANNEL
D
top
important!
the hardware pull should be on the left
side for this step.
slightly angle the remaining door panel (F) into the case as shown below. Insert the door
upward into the track closest to the front of the case. then, allow the door to drop down
into the same track on the bottom panel (C). to confirm that it is installed correctly, just try
sliding the door side to side.

the following instructions describe how to stack
your toy storage units and apply the safety strap
if stacking two or more. if you will not be stacking
your toy storage units, you can stop here.
before you move on!

14 in order to stack these storage units, you’ll need to remove the leg brackets on the under-
side of bottom panel (C). using your philips head screw driver, remove all leg brackets.
still confused? click to watch the assembly video ASSEMBLY VIDEO CHANNEL