studioduc juno 4 drawer dresser/changer User manual

juno 4 drawer
dresser/changer
a how-to guide that won’t leave you in tears
ASSEMBLY INSTRUCTIONS

parenting is hard.
this is easy.
no really, it is.
MADE HERE™
MADE SAFE MADE SMART
MADE WELL™

want to watch this assembly IRL?
(acronym challenged? that means “in real life”.)
open the camera on your phone and place it over the
QR code below to see our NYC studio dream team do all
the heavy lifting (just kidding, there is none!)
or go to ducducnyc.com/assembly-instructions

thank you for selecting a
studio duc product!

Please check contents against the components list in these instructions. Also, please ensure
there was no damage that may have occurred in shipping. If any components are missing or you
find any damage, please contact ducduc before continuing.
To use the dresser as a changing table, insert and use the changing table tray provided with the
dresser.
We recommend the use of a Colgate 3-Sided contour Pad (CR300-S80) if this dresser is to be
used as a changing table.
Maximum changing pad dimensions: W16” x L33” x H5”.
Pay close attention to the safety warnings in these instructions and on dresser/changer labels.
The maximum weight of any child on top of the dresser/changer is 45 pounds.
Read all the instructions before use.
Do not use if dresser/changer is damaged or broken.
CARE AND CLEANING:
Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning. Clean with mild
soap on a soft rag. Rinse and dry thoroughly. If you ever re-finish this furniture, be sure to use
only a non-toxic finish.
Do not attempt to move this dresser/changer alone–dragging or sliding it across a floor may
cause structural damage. A minimum of two people is required to safely lift and reposition the
dresser/changer.
KEEP INSTRUCTIONS FOR FUTURE USE
Please check contents against the components list in these
instructions. Also, please ensure there was no damage that may have occurred in
shipping. If any components are missing or you find any damage, please contact
ducduc before continuing.
To use the dresser as a changing table, insert and use the changing table tray
provided with the dresser.
We recommend the use of a Colgate 3-Sided contour Pad (CR300-S80) if this
dresser is to be used as a changing table.
Maximum changing pad dimensions: W16” x L33” x H8”.
Pay close attention to the safety warnings in these instructions and on dresser/
changer labels.
The maximum weight of any child on top of the dresser/changer is 45 pounds.
Read all the instructions before use.
Do not use if dresser/changer is damaged or broken.
CARE AND CLEANING:
Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning.
Clean with mild soap on a soft rag. Rinse and dry thoroughly. If you ever
re-finish this furniture, be sure to use only a non-toxic finish.
Do not attempt to move this dresser/changer alone- dragging or sliding it across
a floor may cause structural damage. A minimum of two people is
required to safely lift and reposition the dresser/changer.
KEEP INSTRUCTIONS FOR FUTURE USE
secure this unit to support surface using the
mounting hardware provided. see instructions.

WHAT’S IN THE BOX:
A1
L side panel
DB1 (x4)
drawer face
DB2 (x4)
drawer box back
DB3 (x4)
L drawer box side
DB4 (x4)
R drawer box side
DB5 (x6)
drawer box bottom
F
hammer cap
G
safety strap kit
(with hardware)
B
back panel
C
bottom
D
stretcher
A2
R side panel
E
top

I (x2)
tray bracket
J (x8)
JCB bolt (20mm)
K (x8)
5/16” locking
washer
L
allen key (4mm)
H
changing tray
INCLUDED WITH CHANGER ONLY:

WHAT YOU’LL NEED:
20 minutes
(or less)
2 people
plus a dog for moral support
(unless you’re a cat person)
household hammer or
rubber mallet
a soft surface to assemble on
(like a rug or some of the corrugate
box your piece arrived in)
phillips head screwdriver
and/or drill with 6mm bit

lean R side panel (A2) against a wall as shown.
insert connectors of back panel (B) into slots on R side panel (A2). push down at the
connection to lock into place. make sure the pre-drilled holes on back panel (B) are not
facing the drawer glide hardware.
2
1
still confused? scan this code to watch the assembly video!

insert connectors of back panel (B) into slots on L side panel (A1). push down at the
connection to lock into place.
3
4a have a friend gently flare the side panels outward as shown.
still confused? scan this code to watch the assembly video!

4b with the side panels flared outward, insert connectors of bottom panel (C) into slots on R
side panel (A2).
still confused? scan this code to watch the assembly video!

4d once all connectors and slots are lined up and side panels are back to square position,
apply hammer cap (F) to the head of a household hammer and tap bottom panel (C)
until there is no gap at the connection to back panel (B).
4c insert remaining connectors of bottom panel (C) into slots on L side panel (A1).
still confused? scan this code to watch the assembly video!

insert connectors of stretcher (D) into slots on both side panels (A1 + A2). tap with hammer
and hammer cap (F) to lock into place.
5
still confused? scan this code to watch the assembly video!

with a friend, flip partially assembled case into upright position. line up holes of top (E) with
the connectors of side panels (A1 + A2) and back panel (B). tap with hammer and hammer cap
(F) to lock into place.
6
7a now we build the drawers! starting with drawer face (DB1) facing down, insert
connectors of both drawer box side panels (DB3 + DB4) into slots on drawer face (DB1).
push down at the connections to lock into place.
still confused? scan this code to watch the assembly video!

7b rotate the partially assembled drawer box as shown. slide drawer box bottom (DB5) into
place using grooves on the drawer box side panels (DB3 + DB4) as guides. be sure glide
hardware on bottom panel (DB5) is positioned outside the drawer interior and toward
the drawer face (DB1) as shown.
7c again, rotate partially assembled drawer box as shown. insert connectors of drawer box
back (DB2) into slots on drawer box sides (DB3 + DB4). push down at the connections
to lock into place. use hammer and hammer cap (F) if needed.
duc insider tip!
when the drawer bottom panel is properly
installed, it should be recessed about a 1/4”
from the back of the drawer sides.
(don’t be afraid to use some force!)
still confused? scan this code to watch the assembly video!

8build remaining drawers using steps 7a, 7b, and 7c.
starting at the top, pull drawer glides out to extended position as shown.
9a
still confused? scan this code to watch the assembly video!

9b place one assembled drawer box onto extended glides as shown. from underside of
drawer, use hands to pull each glide forward until it locks into connection with glide
hardware attached to drawer box bottom (DB5). the drawer will be secure when you
hear a click on each connection. once secured, push drawer box in to close.
still confused? scan this code to watch the assembly video!

10 repeat steps 9a + 9b to install the remaining drawers.
still confused? scan this code to watch the assembly video!

proceed to the next step if you purchased a changer.
for a dresser, skip to step 12.
before you move on!

11 place changing tray (H) on top of assembled case so the pre-drilled holes at the backs
of both pieces align. starting at one side, place hardware (I) over the holes on the case
and changing tray (H). secure into place using the allen key (L) to screw in hardware
(J + K) as arranged in the picture.
still confused? scan this code to watch the assembly video!
H
I
I
J
K
H
L
I
duc insider tip!
when attaching the changing tray to the
dresser, start by loosely screwing in each
bolt over the bracket. once everything is
lined up and each of the 4 bolts are in place,
fully tighten all screws until secure.
repeat on the remaining bracket using the
same method.