Sumitomo Lynx-CustomFit LYNX2-SC User manual

Lynx‐CustomFit® Splice‐On Connector Ver.2
‐LYNX2‐SC for 250um or 900um Tight Buffered Fiber ‐
Installation Manual
Foryoursafetyoperation Precautions
ETK1123068B
TheLynx‐CustomFit® Splice‐On Connectoris designedand
manufacturedtoassurepersonalsafety.Improperoperation
canresultinbodilyinjuryandseriousdamagetothisproduct.
Pleasereadandobserveallwarningsinstructionsgiveninthis
operationmanual.
Wearsafetyglassestoprotectyoureyeswhen
hdli ti l fib
!
1. Improperassemblywillresultinalossofperformance.
Pleasereadinstructions giveninthisoperationmanual
and the operation manual of the fusion splicer.
2. Never touch the fiber of the stub. It has been inspected
in the factory.
3. Theproductissensitivetodirtordust.Donottakeout
any
parts from the package
until it is to be used
h
an
dli
ngop
ti
ca
l

fib
er.
Neverlookintotheendofamicroscopeoroptical
cableconnectedtoanopticaloutputdevicethatis
operating.Laserradiationisinvisible,anddirect
exposurecanseverelyinjurethehumaneye.
Alcoholisflammable,causesirritationandisharmful
!
!
any
parts

from

the

package

until

it

is

to

be

used
.
4. Thecharacteristicwillbeinfluencedbythefiber
cleavedsurfacecondition.Pleaseuseacleaverwhich
hasagoodcleavingcharacteristic.
5. Donotremovethedustcapuntiltheconnectorhas
beencompletelyassembled inordernottocausean
highinsertionlossduetothem.
ifswallowedorinhaled.Keepalcoholawayfrom
heat,sparks,skin,andavoidcontactwitheyes.
Inthecaseoftheworkatthehighplace,pleasebe
carefulnottodropanassemblingtool.
!
!
Composition
Di bl
R
Fti
Assembling Tools
Ei h
hld
i
id
Di
sposa
bl
e
Holder(*1)
Outer
Inner
Housing
R
ear
Stopper Boot
F
urca
ti
on
Tube Holder (Fiber Side)
for 900um tight buffer for 250um fiber
LYNX2‐UML‐SFHS‐09 FHS‐025 LYNX2‐S‐LB5
Ei
t
h
er one
h
o
ld
er
i
srequ
i
re
d
.
Outer

Housing
Ferrule
Subassembly
ProtectionSleeve
and Spring
(*1) 1 pc / 100 connectors FusionSplicer
T‐Q101‐CA(71C), etc.
FiberCleaver
FC‐6S‐C, etc.
Jacketremover
JR‐M03, etc.
Recommended Program
Splicer Fiber SplicingProgram HeaterProgram
Below equipment or tool are examples.
SMF G 652 G657
T‐25eS SMF SM1: SMF1C Lynx
or FPS (60mm)
MMF MM1: MMF1C
T‐39FH SMF LYNX‐SM Lynx
or FPS (60mm)
MMF LYNX‐MM
T‐Q101‐CA
(T‐71C)
SMF Standard SMF Lynx
or 60mm 0.9
MMF MMF 50&62.5
PleaseperformArctestpriortothesplicingoperation.
(Seethe operation manual of the splicer.)
*Fiberfortestingisnotincludedinthekit.
HolderType Cleave length: 10mm
Copyright©2011SumitomoElectricIndustries,LTD.
SMF
:
G
.
652
,
G
.
657
MMF:MM50(OM2),MM50(OM3),MM50(OM4),MM62.5(OM1) Pleasecheckfibertypeinsidethefieldfiber.
North Carolina (USA)
SumitomoElectricLightwaveCorp.
78 Alexander Drive, P.O. Box 13445, RTP, NC 27709
TEL+1‐919‐541‐8100
http://www.sumitomoelectric.com/
Yokohama (Japan)
SumitomoElectricIndustries,Ltd.
(LightwaveNetworkProductsDivision)
1, Taya‐cho, Sakae‐ku, Yokohama 244‐8588, Japan
TEL+81‐45‐853‐7223, http://global‐sei.com/fttx/
London (UK)
SumitomoElectricEuropeLtd.
220 Centennial Avenue, Elstree, Herts. WD6 3SL, UK
TEL+44 (0)20‐8953‐8118
http://www.sumielectric.com/

LYNX2‐SCfor250um or 900um Tight Buffer
Assembly Procedure ETK1123068B
(A) Set Fusion Condition (B) Perform Arc Test
Then perform the arc test
according to the
instruction.
*Fiberfortestingisnot
included in the kit
(1) Slide Rear Parts onto the
fiber.
(2) Slide Protection Sleeve onto the
fiber.
(3) Remove the fiber coating.
Approx. 35mm (JR‐M03)
0.9to0.25mm
0.25to0.125mm (4) Clean the fiber with lint‐
free cleaning wipe.
Push “power
key” for more
than 1 sec.
“Main Menu”
Select Fiber Type Select “FiberType”, then “Return”. Select “Arc Test”
included

in

the

kit
.
Pleasecheckfibertype
insidethefieldfiber.
“Main Manu”
Select Sleeve Type
Select Sleeve Type
Then “Return”
Seetheoperationmanualofeachsplicer.ThesearetheexampleofT‐Q101‐CA(T‐71C).
Insertfiberinto
thishole
Moistened
withalcohol
(5) Set the fiber on theholder. Confirmtheposition
Good
Donottouch
barefiber
1. Place
(6) Cleave the fiber (FC‐6S)
Nogap
(7) Setfiberholderonthesplicer
(leftside).
2. Close
No Good
No Good
3. Slide
Cleanrubberclamp
andbladeregularly
(8) Pick up the stub and set the stub on the plastic holder. (9) Setstubholderonthesplicer
(rightside).
(10) Fusion Splice.
Push to
close
Placefiberon
V‐groovegently
Grasphereto
pick up
Donottouch
barefiber Placefiberon
V‐groovegently If the position of the fiber is wrong,
set the fiber or stub again.
(11) Open the stub and fiber holders. (12) Pick up the spliced fiber.
Nii
(13) Slide Protection untilitcoverstheprojectionof
theflange.
Left
side
first
Then right side
Buttonto
startsplicing
Lightlyholdingassemblytopreventbending
Lightlymaintainingtensionto
preventbending
N
otw
i
st
i
ng
(14) Set Sleeve into the heater. (15) Confirm the position before
heating. Sleeveatcenter
f h
Buttonto
tthti
(16) Heat Protection Sleeve.
Right side first Then left side
Notwisting
Left
side
first
Notwisting
o
f

h
eater
Nogap
s
t
ar
t

h
ea
ti
ng
Lynxheaterprogram runsafanto
coolthesleeveafterheating
(17) Pick up Sleeve. (18) Put Inner Housing. (19) Put Outer Housing.
Lightlymaintaining
tensiononfiber
Copyright©2011SumitomoElectricIndustries,LTD.
Becareful for hot sleeve,
spring and flange even after
the cooling by fan.
!
Red
Triangle
APC‐ Reddot
PC/UPC‐ Blackdot CutTether
Key
Key
Complete